Bronze 20 degrees tilt-element thru-hull w/temp for 16 degrees to 24 degrees hull deadrise (Beam angle:45 degrees @50kHz,12 degrees @200kHz)

Bronze 12 degrees tilt-element thru-hull w/temp for 8 degrees to 15 degrees hull deadrise (Beam angle:45 degrees @50kHz,12 degrees @200kHz)

B-60-20 Tilted Element Transducer Low profile tilted element for 16° to 20° deadrise hulls. Features: 600 Watts Dual 50/200kHz

B164-20 20° 1kW Tilted Element Transducer with 6-Pin Connector Features: Depth/Temp 50/200 kHz 1 kW RMS High-performance Bronze Step up to a 1kW without a Fairing! Airmar has taken our innovative Tilted Element™ technology to a higher power. The 1kW, flush-mount, tilted element transducers are perfect for fast, trailered tournament sport fishing vessels who cannot have a high-performance fairing. The flush mounted, bronze housing protrudes less than 6.35 mm (0.25) outside your hull and can sit on trailer rollers and bunks with no damage at all. The ceramic arrays are tilted inside the housing giving you the perfect vertical beam with maximum energy on what is directly below your boat. Take your fishfinder to the next power with Airmars 1kW tilted element transducers. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

B-60-12 Tilted Element Transducer Low profile tilted element for 8° to 15° deadrise hulls. Features: 600 Watts Dual 50/200kHz

Bronze 20 degrees tilt-element w/temp for 16 degrees to 24 degrees hull deadrise (Beam angle:22 degrees @50kHz, 6 degrees @200kHz)

SI-TEX 300/50/200T Bronze Thru-Hull Transducer Dual Frequency 50/200 kHz Max Power: 600W Beam Angle: 43 deg. @ 50 kHz, 9 deg. @ 200 kHz Housing: Bronze Mount: Through Hull Plug: Two 8 pin Cable: 30' Temp: Yes Speed: No For SI-TEX model: CVS208/209

250C/50/200ST-CX Transom Mount Transducer SI-TEX 250C/50/200ST-CX Transom Mount Transducer for the CVS-126 and CVS-128.

B175L Bronze Low Profile Thru Hull 20° Tilted Element Transducer 1kW Features Material: Bronze For use with CP450C or CP470 Chirp Sonar Module Power (RMS): 1Kw Max Depth(ft): 2,500 Frequency (khZ): 40-60 Beam Width(L/H): 32°-21° Records: Depth / Temperature Approved Hull Material: Fiberglass / Wood Cable Length (Ft/M): 33ft / 10M Supported Deadrise / Transom Angles: 16-24° Deadrise Note: Using a Single B175 or B75 requires the A80328 Single Operation Cable

B60 Tilted Element™ 20° 20° titled version is designed for 16° - 24° deadrise angles For use with Raymarine DSM250/DSM300/DSM300G/DSM30/CP300 The bronze B60-20° provide a vertical beam without a fairing. Inside the housing, the ceramic element is tilted to provide built-in deadrise compensation. The resulting vertical beam provides excellent echo returns for more accurate depth readings. The nearly flush housing minimizes drag with only 5 mm (3/16") extending outside of the hull. Features: Depth/Temp 50/200 kHz 600w RMS Mid-performance Bronze

CVS-126 with B60 20° Transducer CVS-126 Dual Frequency Color LCD Echo Sounder The SI-TEX CVS-126 Dual-Frequency (50/200kHz) Echo Sounder features a digital signal processor (DSP) for a clearer image that enhances fish targets in shallow and deep depths, plus auto function for the most reliable setting and best performance. Features: Digital 5.7" Dual-Frequency Color LCD Fishfinder DSP technology for a clearer detailed image that enhances fish targets Digital signal processing State-of the-art digital signal processor offers advanced filtering capabilities Digital Filtering feature eliminates clutter by filtering out the noise to provide a clear detailed image that enhances fish targets in shallow and deep depths Making it easy to differentiate between baitfish, larger fish, schools of fish and the sea floor Sona-Tone Exclusive Sona-Tone identifies what's under your boat with different sounds for fish and schools of fish. So you will not miss any good opportunites even if you are away from the CVS-126 Automatic Functions For best performance the Auto Function mode chooses the most reliable setting for such functions as Gain, Range and Shift Optimum settings are continuously selected automatically (GAIN, RANGE, SHIFT) Fishing Hot Spots Leads you back to your favorite fishing hot spots or other previously saved positioning in memory with input from optional GPS sensor Store the Image YouStores up to 10 screen images in built-in memory for recalling later by "one-touch" Great for recalling a potential hot spot for review later Easy Operation Easy access to all system functions with simply arranged keypad, dedicated-functions keys, rotary-knob control of Gain/Selection and comprehensive on-screen menus Sunlight Viewable Brilliant 5.7" color LCD display with 8, 16, or 64 color levels and an anti-reflective coating for excellent readability in direct sunlight B60 20° Transducer B-60-20-CX Low profile 20° tilted element transducer for 16° to 20° deadrise hulls. Features: 600 Watts Dual 50/200kHz

B175MW Med Ultra Wide 1kW, 20° Chirp Thru-Hull Transducer f/12-Pin Garmin175MW Med Ultra Wide 20 Degree, 1KW Chirp Thru-hull Transducer with 12 Pin Connector for Garmin  Airmar's innovative transducer designs have revolutionized the fishing world, and they continue to do so with the Chirp-ready B175 Medium Ultra-Wide (MW) Tilted Element™ Thru-hull transducer. The B175MW takes transducer design and performance to a whole new level by using medium frequency (60-100 kHz) with an incredible ultra-wide beamwidth ranging from 57-73° port-starboard to 16° average fore-aft. Maximum coverage under the boat is achieved with this medium-frequency transducer, serving anglers who target pelagic species in the upper water column. Airmar’s Medium Ultra-Wide models are perfect for seeking deeper species with a frequency band from 60-100 kHz. When paired with our other popular models such as the B275LHW, provides the angler with a broad set of frequencies (Low, Medium-Wide, High-Wide) to interrogate targets from deep to shallow. The B175MW Tilted Element Thru-hull is a 1 kW transducer housed in one of AIRMAR’s most popular Tilted Element housings which includes a ceramic element fixed at a 20° angle. Because the transducer is installed almost flush with the hull, the tilted element corrects for the hull deadrise and orients the ceramic element vertically to ensure maximum echo returns to the transducer. Features: Fixed 20° tilted version for 16° to 24° hull deadrise 12 Pin Connector for Garmin FishFinders Depth and fast-response water-temperature sensor 1 kW with depth tracking down to 400 m (1,300#39;) Medium frequency: 60-100 kHz 57° to 73° beamwidth (port/starboard) 16° average fore/aft 40 kHz of total bandwidth from one transducer Medium frequency for superior mid-depth performance and excellent fish-target separation Bronze housing for use on stepped, planing, or displacement hull Low-profile, thru-hull housing yields good resolution at speed when installed properly Exclusive Xducer ID® technology Specifications: Brand: Airmar Technology Acoustic Window: Urethane Cable-Length: 9 m (30'), 10 m (33') Common Use: Fishing Connector: Garmin 12-Pin Country of Origin: USA Display Connector: 12G Functions: Depth, Temperature Hole Size: 95 mm (3-3/4") Hull Material: Fiberglass or wood Material: Bronze Max Deadrise Angle: 24° Max Depth: 400 m (1300') Max Vessel LOA: Up to 11 m (36') Medium Frequency: 60-100 kHz Medium Frequency Beamwidth: 57° to 73° (Port/Starboard) X 16° average (Fore/Aft) Medium-Wide Beamwidth: 57° to 73° beam p/s 16° average f/a Mounting Style: Tilted Element Thru-Hull Power Rating: 1 kW Single or Dual Frequency: Single Tilt Angle: 20° Tilted Element: Yes Water Temperature: -10° to 40°C (14° to 104°F) Weight: 2.7 kg (6 lbs.) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B164 Tilted Element™ 20° Features: Depth/Temp 50/200 kHz 1 kW RMS High-performance Bronze Step up to a 1kWWithout a Fairing! Airmar has taken our innovative Tilted Element™ technology to a higher power. The new 1kW, flush-mount, tilted element transducers are perfect for fast, trailered tournament sport fishing vessels who cannot have a high-performance fairing. The flush mounted, bronze housing protrudes less than 6.35 mm (0.25) outside your hull and can sit on trailer rollers and bunks with no damage at all. The ceramic arrays are tilted inside the housing giving you the perfect vertical beam with maximum energy on what is directly below your boat. Take your fishfinder to the next power with Airmars 1kW tilted element transducers. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B164-12 12° 1kW Tilted Element Transducer with 6-Pin Connector Features: Depth/Temp 50/200 kHz 1 kW RMS High-performance Bronze Step up to a 1kW Without a Fairing! Airmar has taken our innovative Tilted Element™ technology to a higher power. The 1kW, flush-mount, tilted element transducers are perfect for fast, trailered tournament sport fishing vessels who cannot have a high-performance fairing. The flush mounted, bronze housing protrudes less than 6.35 mm (0.25) outside your hull and can sit on trailer rollers and bunks with no damage at all. The ceramic arrays are tilted inside the housing giving you the perfect vertical beam with maximum energy on what is directly below your boat. Take your fishfinder to the next power with Airmars 1kW tilted element transducers. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

B164 Tilted Element™ 20 degree titled version is designed for 16 degree - 24 degree deadrise angles. for use with Raymarine DSM250, DSM300 sounder modules Features: Depth/Temp 50/200 kHz 1 kW RMS High-performance Bronze Step up to a 1kW Without a Fairing! Airmar has taken our innovative Tilted Element™ technology to a higher power. The new 1kW, flush-mount, tilted element transducers are perfect for fast, trailered tournament sport fishing vessels who cannot have a high-performance fairing. The flush mounted, bronze housing protrudes less than 6.35 mm (0.25) outside your hull and can sit on trailer rollers and bunks with no damage at all. The ceramic arrays are tilted inside the housing giving you the perfect vertical beam with maximum energy on what is directly below your boat. Take your fishfinder to the next power with Airmars 1kW tilted element transducers.