|
GS-2-50 Grounding Strap - 2" x 50'
This grounding strap is an ideal conductor for RF grounding of SSB radios and other noise-sensitive transceivers, for bonding thru-hulls, etc.
Features:
Flexible (easily conforms to vessel contours)
.01 in. (25mm) thick
Specifications:
Width (in./cm): 2/5.1
Length (ft./m): 50/17
Weight (lbs/kg): 5/2.3
|
212.75 |
|
|
GS-2-100 Grounding Strap - 2" x 100'
This grounding strap is an ideal conductor for RF grounding of SSB radios and other noise-sensitive transceivers, for bonding thru-hulls, etc.
Features:
Flexible (easily conforms to vessel contours)
.01 in. (25mm) thick
Specifications:
Width (in./cm): 2/5.1
Length (ft./m): 100/33
Weight (lbs/kg): 8/3.6
|
422.41 |
|
|
GS-2-25 Grounding Strap - 2" x 25'
This grounding strap is an ideal conductor for RF grounding of SSB radios and other noise-sensitive transceivers, for bonding thru-hulls, etc.
Features:
Flexible (easily conforms to vessel contours)
.01 in. (25mm) thick
Specifications:
Width (in./cm): 2/5.1
Length (ft./m): 25/8
Weight (lbs/kg): 3/1.4
|
106.85 |
|
|
March 0150-0125-0200-2.50 Imp Mag Assy Encap W/2.50
|
115.44 |
|
|
Scot Pump 35068-J-2.50 MOTOR/PUMP 2.5" IMPELLER
Pump
• All Bronze marine centrifugal pump Freshwater or seawater applications
• Precision machined to close tolerances for consistent performance.
• Hardware - Type 303 stainless steel
• Semi-open impeller handles solids
• Heavy-duty. Use for continuous 24 hour – 7 day operation.
• Stainless steel shaft.
Shaft Seal
• Rated at 75 PSI – 5 BAR
• Seawater Buna rubber parts, ceramic stationary and carbon rotating element, stainless steel spring and metal components
Motor – 2 Pole
• Totally enclosed fan cooled IP-44 motors meet marine, European, and Coast Guard ignition protected requirements.
• Sealed ball bearings
• Single-phase capacitor start 50 Hz - 110/220 Volt 60 Hz – 115/230 Volt
• Motors are dual frequency 50 Hz or 60 Hz
• Three phase motors are not available
|
1031.22 |
|
|
Scot Pump 35067-2.50 Motor/Pump Unit
• Compact
• Enclosed Switch Compartment
Pump
• All Bronze marine centrifugal pump Freshwater or seawater applications
• Precision machined to close tolerances for consistent performance.
• Hardware - Type 303 stainless steel
• Semi-open impeller handles solids
• 2.50" Impeller mounted on motor shaft
• Heavy-duty, designed for continuous 24 hour – 7 day operation.
Shaft Seal
• Rated at 75 PSI – 5 BAR
• Seawater Buna rubber parts, ceramic stationary and carbon rotating element, stainless steel spring and metal components
Motor – 2 Pole
• Meets Coast Guard ignition protected requirements. The thermal protector and starting switch are in the enclosed outlet cover.
• Sealed ball bearings
• Single-phase capacitor start 50 Hz - 110/220 Volt 60 Hz – 115/230 Volt
• Dual frequency 50 Hz or 60 Hz single phase motors are available
• Stainless steel shaft
• Three phase motors are not available
|
1000.62 |
|
|
2000lb 2-Speed Winch - Strap Not Included
Features
Make light work of heavy load with Fulton brand two-speed winches. One fast speed for quick pull-in, a seconds low speed for increased mechanical advantage.
Our shift lock design allows changing gears without moving the crank handle from shaft to shaft. Just lift the shift lock and slide the shaft into the desired gear position. Shift lock holds the shaft in gear.
Neutral, free-wheel position allows quick line pay out without spinning the handle.
5 year limited warranty
Specs:
Capacity (lbs.): 2,000
Handle Length: 10"
Gear Ratio: 4.1:1 & 9.8:1
Strap: 20' x 2"
Hub Size: 1"
Hand Brake: optional
Strap Included: Yes
WARNING: This product can expose you to chemicals including BISPHENOL A (BPA) which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
137.20 |
|
|
2600lb 2-Speed Winch - Strap Not Included
Winch, 2600 lbs., 2-Speed
Features
Make light work of heavy load with Fulton brand two-speed winches. One fast speed for quick pull-in, a seconds low speed for increased mechanical advantage.
Our shift lock design allows changing gears without moving the crank handle from shaft to shaft. Just lift the shift lock and slide the shaft into the desired gear position. Shift lock holds the shaft in gear.
Neutral, free-wheel position allows quick line pay out without spinning the handle.
5 year limited warranty
Specs:
Capacity (lbs.): 2,600
Handle Length: 10"
Gear Ratio: 5.1:1 & 12.2:1
Strap: 20' x 2" (Not Included)
Hub Size: 1"
Hand Brake: optional
Strap Included: No
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
159.14 |
|
|
Hypro 3800-0046 1/4"-1/2" 50 Mesh Screen
|
3.19 |
|
|
Hypro 3800-0066 1 1/2" 50 Mesh Screen
|
17.13 |
|
|
HTM-2 Fender 8.5" x 20.5" - Black with Adapter
In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications. Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.
The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced tube ends
Designed for medium-duty use in both permanent protected and unprotected moorings
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm)
Tube Diameter - 0.625" (1.6cm)
Circumference - 26.7" (67.9cm)
Volume - 4.7 gallons (17.8L)
Boat Size - 25' - 30' (7.6 - 9.1M)
Weight - 4.7lb
In the Box:
Fender
Inflation Adapter
*Sold as a Kit
|
62.23 |
|
|
HTM-2 Fender 8.5" x 20.5" - Blue with Adapter
In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications. Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.
The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced tube ends
Designed for medium-duty use in both permanent protected and unprotected moorings
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm)
Tube Diameter - 0.625" (1.6cm)
Circumference - 26.7" (67.9cm)
Volume - 4.7 gallons (17.8L)
Boat Size - 25' - 30' (7.6 - 9.1M)
Weight - 4.7lb
In the Box:
Fender
Inflation Adapter
*Sold as a Kit
|
62.23 |
|
|
HTM-2 Fender 8.5" x 20.5" - White with Adapter
In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications. Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.
The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced tube ends
Designed for medium-duty use in both permanent protected and unprotected moorings
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm)
Tube Diameter - 0.625" (1.6cm)
Circumference - 26.7" (67.9cm)
Volume - 4.7 gallons (17.8L)
Boat Size - 25' - 30' (7.6 - 9.1M)
Weight - 4.7lb
In the Box:
Fender
Inflation Adapter
*Sold as a Kit
|
62.23 |
|
|
HTM-2 Fender 8.5" x 20.5" - Black
In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications. Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.
The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced tube ends
Designed for medium-duty use in both permanent protected and unprotected moorings
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm)
Tube Diameter - 0.625" (1.6cm)
Circumference - 26.7" (67.9cm)
Volume - 4.7 gallons (17.8L)
Boat Size - 25' - 30' (7.6 - 9.1M)
Weight - 4.7lb
*Sold as an Individual
|
61.68 |
|
|
HTM-2 Fender 8.5" x 20.5" - Blue
In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications. Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.
The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced tube ends
Designed for medium-duty use in both permanent protected and unprotected moorings
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm)
Tube Diameter - 0.625" (1.6cm)
Circumference - 26.7" (67.9cm)
Volume - 4.7 gallons (17.8L)
Boat Size - 25' - 30' (7.6 - 9.1M)
Weight - 4.7lb
*Sold as an Individual
|
61.68 |
|