March 893-10-1/4" 24V Pump W/ 1286-0002-0100

March 893-10 Brushless 24V DC Pump Applications for the March 893-10 Magnetic Drive Pump include computer cooling, photographic processing equipment, refrigeration systems, and water displays.   March Pump's industrial 893-10 is an American submersible seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and heat transfer. It is capable of generating a maximum flow of 2.7 gallons per minute at 1 foot, and its maximum head is 10.6 Feet (or around 4.5PSI).  The pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Noryl, Nylon, Carbon/Teflon, Buna N, Stainless Steel, and Ceramic Magnet.  When submerged Epoxy, Delrin, and the motor leads are also in contact with the solution. The inlet connection is 0.375 inch female pipe thread, and the outlet is 0.375 inch smooth. The standard motor is a 0.006 Horsepower DC Brushless Motor, available in 24 Volts.  The 24 Volt Motor has an operating range from 12 to 28 Volts.  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius when not submerged, or 130 Fahrenheit or 54 Celsius when submerged. The March 893-10 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Max Flow 2.7 GPM 11 LPM Max Head 10.6 FT 3.3 M Power .006 HP .004 KW Electrical 24V Range 12-28V Submersible Yes   Type Centrifugal Mag Drive Inlet 3/8"FPT Outlet 3/8"OD Wet End Noryl (Front and Rear Housings), Nylon (Impeller), Carbon/Teflon (Thrust Washer), Buna N (O-Ring), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Delrin, Motor Leads    

March 893-04 Brush 12V DC Pump Applications for the March 893-04 Magnetic Drive Pump include marine refrigeration and water displays. March Pump's industrial 893-04 is an American submersible seal-less centrifugal magnetic drive pump ideal for applications such as marine equipment. It is capable of generating a maximum flow of 2.7 gallons per minute at 1 foot, and its maximum head is 10.6 Feet (or around 4.5PSI). The 893-04 must be used submerged. The standard wet end (the materials that come into contact with the solution) is composed of Noryl, Nylon, Carbon/Teflon, Buna N, Stainless Steel, and Ceramic Magnet.  When submerged Epoxy, Delrin, and the motor leads are also in contact with the solution. The inlet connection is 0.375 inch female pipe thread, and the outlet is 0.375 inch smooth. The standard motor is a 0.006 Horsepower DC Brushtype Motor, available in 12 Volts.  The 12 Volt Motor has an operating range from 0 to 14 Volts.  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 160 Fahrenheit or 71 Celsius. The March 893-04 centrifugal magnetic drive pump is capable of handling mild corrosive chemicals, acids, and solvents.     Max Flow 2.7 GPM 11 LPM Max Head 10.6 FT 3.3 M Power .006 HP .004 KW Electrical 12V Range 0-14 Submersible Yes   Type Centrifugal Mag Drive Inlet 3/8"FPT Outlet 3/8"OD Wet End Noryl (Front and Rear Housings), Nylon (Impeller), Carbon/Teflon (Thrust Washer), Buna N (O-Ring), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Pump must be used submerged When submerged, the following is also in contact with the solution Epoxy, Delrin, Motor Leads  

Applications for the March 893-07 Magnetic Drive Pump include computer cooling, photographic processing equipment, refrigeration systems, and water displays.    March Pump's industrial 893-07  is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and heat transfer. It is capable of generating a maximum flow of 2.7 gallons per minute at 1 foot, and its maximum head is 10.6 Feet (or around 4.5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Noryl, Nylon, Carbon/Teflon, Buna N, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch female pipe thread, and the outlet is 0.375 inch smooth. The standard motor is a 0.006 Horsepower DC Brushless Motor, available in 12 Volts.  The 12 Volt Motor has an operating range from 7 to 14 Volts.  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March 893-07 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Max Flow 2.7 GPM 11 LPM Max Head 10.6 FT 3.3 M Power .006 HP .004 KW Electrical 12V Range 7-14   Type Centrifugal Mag Drive Inlet 3/8"FPT Outlet 3/8"OD Wet End Noryl (Front and Rear Housings), Nylon (Impeller), Carbon/Teflon (Thrust Washer), Buna N (O-Ring), 316 Stainless Steel (Shaft), Ceramic Magnet

March 0135-0042-1000 Screw Stainless Steel Screw Round Head Slotted #8-32 x 1/4"LG for March Pumps 2C-MD, AB-F, AB-FK, MDX, LC & AC-2C-MD, 823, 802, 210, 212

March 0155-0014-1000 Screw Screw Cap Hex Head 1/4-20 x 2" for all March 7 Series Pumps made of 300 Series SS

March 893-11-1/2 +Pump/12V Mtr 1/2"Ports This item is 'build to order'. Please contact us for lead time.

Applications for the TE-7K-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, deionized water systems, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.    March Pump's industrial TE-7K-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 53 gallons per minute at 10 feet, and its maximum head is 60 Feet (or around 26PSI). The standard wet end (the materials that come into contact with the solution) is composed of carbon filled Kynar (PVDF), Viton, Carbon, and Ceramic. The inlet connection is 1.5 inch female pipe thread, and the outlet is 1 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.75 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 75PSI, and the maximum liquid temperature is 200 Fahrenheit or 93 Celsius. The March TE-7K-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 53 GPM 180 LPM Max Head 60 FT 12.3 M Power .75 HP .559 KW Electrical 1PH 115/230V or 3PH 230/460V 50/60HZ     Type Centrifugal Mag Drive Inlet 1-1/2"FPT Outlet 1"MPT Wet End Carbon Filled Kynar (Front Housing, Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers), Carbon (Bushing) Motor Options Available in .75HP, 1HP, 1.5HP, 1HP Explosion Proof, or 1.5HP Explosion Proof

Oberdorfer 405M-4-24N18Bct Pump 1Hp 1800Rpm 24V FEATURES Pump Body: Bronze Ports: 1" NPT and 1 1/2" Hose Flow: 24 GPM at 20 feet of head Impeller: Neoprene Standard, Buna Optional Shaft Seal: Mechanical Shaft: Stainless Steel Motor / Drive: Close coupled Rubber Impeller Pumps are mounted directly onto the motor without the use of a shaft coupling. This pump is designed to be coupled to a Nema C 56C faced motor. It uses an aluminum adapter plate to accommodate the pump. The gas engine mount has its own adapter. We can supply additional motors and assemble for you.     APPLICATIONS / CHARACTERISTICS RUBBER IMPELLER PUMP BRONZE CLOSE COUPLED Close coupled Rubber Impeller Pumps are made of high quality bronze for maximum corrosion resistance. The rubber impeller is mounted on a separate stainless steel shaft which is counterbored on the outer end in order to slide over the carbon steel motor shaft. Ball or sleeve bearings in the motor or engine support the shaft. Model 405M has a mechanical seal. Impellers are made of Neoprene rubber, Buna N impellers are available on request. Suction lifts of 15 ft. are possible when pump is fully primed. Portable. Compact. Easy Impeller Replacement. Vacuum Switch Shut-off Optional.     Oberdorfer Flexible Impeller Utility Pump, 1"NPT Ports, Neoprene Impeller, 1HP 24V 1800RPM TEFC Motor  

Oberdorfer 405M-4-12N18Bct Pump 1Hp 1800Rpm 12V FEATURES Pump Body: Bronze Ports: 1" NPT and 1 1/2" Hose Flow: 24 GPM at 20 feet of head Impeller: Neoprene Standard, Buna Optional Shaft Seal: Mechanical Shaft: Stainless Steel Motor / Drive: Close coupled Rubber Impeller Pumps are mounted directly onto the motor without the use of a shaft coupling. This pump is designed to be coupled to a Nema C 56C faced motor. It uses an aluminum adapter plate to accommodate the pump. The gas engine mount has its own adapter. We can supply additional motors and assemble for you.     APPLICATIONS / CHARACTERISTICS RUBBER IMPELLER PUMP BRONZE CLOSE COUPLED Close coupled Rubber Impeller Pumps are made of high quality bronze for maximum corrosion resistance. The rubber impeller is mounted on a separate stainless steel shaft which is counterbored on the outer end in order to slide over the carbon steel motor shaft. Ball or sleeve bearings in the motor or engine support the shaft. Model 405M has a mechanical seal. Impellers are made of Neoprene rubber, Buna N impellers are available on request. Suction lifts of 15 ft. are possible when pump is fully primed. Portable. Compact. Easy Impeller Replacement. Vacuum Switch Shut-off Optional.   Oberdorfer Flexible Impeller Utility Pump, 1"NPT Ports, Neoprene Impeller, 1HP 12V 1800RPM TEFC Motor  

Gianneschi ACB332-24V 1 1/4" Self Prime 24V Main pump features:  Outstanding self-priming Side channel and liquid ring construction Simple and compact   Applications:  Ballast Bilge Diesel oil F.W./S.W. Washing Fire-fighting S.W feeding WPS - Hydrofore   Port Size: From 1'' 1/4 to 1'' 1/2 BSP Pump casing: Bronze Impeller / Gear: Bronze Shaft: Stainless steel

March 0140-0002-0100 Impeller For 140  

March 0750-0227-0100 Self Priming Reservoir This self priming reservoir is used on the following March Series 4 and Series 5 pumps: AC-4C-MD, BC-4C-MD, BC-4K-MD, AC-5C-MD, TE-5C-MD, and TE-5K-MD

March 0130-0019-0100 Pump Housing Housing (Rear) & Plug Assy LC for LC-3CP-MD made of Polypro/Glass

March 0150-0031-0100 Pump Housing