|
March 0130-0140-1200 Motor (Bc) 115V 50/60Hz
|
473.00 |
|
|
March 0130-0049-1200 Motor (Bc) 230V 50/60Hz
|
475.00 |
|
|
March 815 PL C Beer Pump
March Pump’s industrial 815-PL-C is an American seal-less centrifugal magnetic drive pump ideal for applications such as home brewing and hot water systems. It is capable of generating a maximum flow of 8 gallons per minute at 3 feet, and its maximum head is 18.6 Feet (8PSI).
At 60Hz
SystemUS Metric
Max Flow8 GPM 30.3 LPM
Max Head18.6 FT 5.7 M
Power0.04 HP 0.029 KW
At 50Hz
USMetric
7.9 GPM30 LPM
13.5 FT4.1 M
0.04 HP0.029 KW
Electrical: 115V 50/60Hz or 230V 50/60Hz
Inlet: 3/8"FPT & 3/4"MPT
Outlet: 1/2"MPT
Wet End: Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Max Internal Pressure: 50 PSI / 3.4 bar
Max Liquid Temperature: 250 °F / 121 °C
Applications for the 815-PL-C Magnetic Drive Pump include home brewing, hot water systems, solar heating, and fryers.
The 815-PL-C has pumped Cutting Oils, Ethylene Glycol, Hot Water, Hot Wort and Salt Water.
|
332.48 |
|
|
March 0135-0036-1000 Motor 115 volt
Motor AC 115V 50/60HZ 3500 RPM SB No Base 38"Cord used on models MDX-3 and MDXT-3
|
176.80 |
|
|
March 0135-0114-1000 Motor
Motor (AC) 115V 50/60HZ 3500RPM SB (w/Base) 38" Cord for MDX-MT3
(AC) = Open Fan Cooled Motor
|
214.24 |
|
|
March 0125-0052-1000 Motor
Motor (AC) 115V 50/60HZ 3500RPM SB (w/Base) 38" Cord for AC-2C-MD, AC-2CP-MD
|
195.52 |
|
|
March 809 PL HS 115V 50/60 115V 50/60 Pump/Base 6'
|
359.45 |
|
|
March 809 SS HS C 115V 50/60 115V 50/60 Beer Pmp/Base 6'
|
444.99 |
|
|
FINISH THOMPSON M5 MOTOR 230V 1PH 50/60HZ
|
570.00 |
|
|
Applications for the BC-2CP-MD Mag Drive include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.
March Pump's industrial BC-2CP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 5 gallons per minute at 2 feet, and its maximum head is 13 Feet (or around 5.5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, and Ceramic. The inlet connection is 0.375 female pipe thread and 0.75 male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.025 Horsepower blast cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheitor 87 Celsius. The March BC-2CP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Unit System 60Hz 50Hz Max Flow
5 GPM
18.5 LPM
Max Head
13 FT
2.7 M
Power
.025 HP
.018 KW
Electrical
115V 50/60HZ or 230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
3/8"FPT & 3/4"MPT
Outlet
1/4"MPT
Wet End
Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washer)
|
414.38 |
|
|
Applications for the BC-3CP-MD Magnetic Drive Pump include ice makers, laboratory and medical equipment, vapor degreasers, and marine air conditioning systems.
March Pump's industrial BC-3CP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 10 gallons per minute at 1 feet, and its maximum head is 20.5 Feet (or around 9PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, and Ceramic. The inlet connection is 0.75 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.066 Horsepower blast cooled motor, which can be run on 50 and 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March BC-3CP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Unit System 60Hz 50Hz Max Flow
10 GPM
33 LPM
Max Head
20.5 FT
4.5 M
Power
.066 HP
.049 KW
Electrical
115V 50/60HZ or 230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
3/4"FPT
Outlet
1/2"MPT
Wet End
Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washer)
|
569.06 |
|
|
March BC-4C-MD Magnetically Coupled Pump 230V
Applications for the BC-4C-MD Magnetic Drive Pump include electronic medical equipment, etching machines, photo processing equipment, hospital thermal blankets, and food heating cabinets.
March Pump's industrial BC-4C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 14 gallons per minute at 1 feet, and its maximum head is 21.5 Feet (or around 9PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.1 Horsepower blast cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March BC-4C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Unit System 60Hz 50Hz Max Flow
14 GPM
50 LPM
Max Head
21.5 FT
4.7 M
Power
.1 HP
.074 KW
Electrical
115V 50/60HZ or 230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
1"FPT
Outlet
1/2"MPT
Wet End
Polypropylene (Front and Rear Housing, Impeller), Ceramic (Shaft, Thrust Washers), Viton (O-Ring)
|
630.00 |
|
|
Applications for the BC-3CP-MD Magnetic Drive Pump include ice makers, laboratory and medical equipment, vapor degreasers, and marine air conditioning systems.
March Pump's industrial BC-3CP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 10 gallons per minute at 1 feet, and its maximum head is 20.5 Feet (or around 9PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, and Ceramic. The inlet connection is 0.75 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.066 Horsepower blast cooled motor, which can be run on 50 and 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March BC-3CP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Unit System 60Hz 50Hz Max Flow
10 GPM
33 LPM
Max Head
20.5 FT
4.5 M
Power
.066 HP
.049 KW
Electrical
115V 50/60HZ or 230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
3/4"FPT
Outlet
1/2"MPT
Wet End
Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washer)
|
577.50 |
|
|
March 0130-0177-0100 Marine Pump LC-3M-MD
March Pump’s industrial LC-3M-MD is an American submersible seal-less centrifugal magnetic drive marine pump. It is capable of generating a maximum flow of 8.5 gallons per minute at 4 feet, and its maximum head is 19 Feet (8PSI). The LC-3M-MD pump may be used submerged or not submerged. The pump is Ignition Protected per SAE J1171 and ISO 8846, and has extended run dry protection thru the use of a carbon bushing. It is capable of 24,000 BTU a hour.
System: 115v 50/60Hz
Max Flow: 8.5 GPM
Max Head: 19 FT
Power: 0.05 HP
Electrical/Air: 115V 50/60Hz
115V Motor
6 Foot Cord, Submersible
60Hz: 1Ph 0.05HP/0.037kW, 2 AMPS, 3450 RPM
50Hz: 1Ph 0.05HP/0.037kW, 2.3 AMPS, 2850 RPM
Inlet: 3/4"FPT
Outlet: 1/2"MPT
Submersible: Yes
Wet End: Polypropylene (Front and Rear Housing, Impeller), Cupric Nickel (Cooling Tube), Buna N (O-Ring, Cooling Tube Seal), Carbon (Impeller Bushing) Ceramic (Shaft, Thrust Washer), Ceramic Magnet
Uses: Submersible or Open Air
When submerged, the following is also in contact with the solution: Epoxy, Stainless Steel, Polysulfone, Cord
Max Internal Pressure: 25 PSI / 1.7 bar
Max Liquid Temperature: 130 °F / 54 °C
Ignition Protected per SAE J1171 and ISO 8846: Rated IP 67
UL Listed Motor:
Note: Product image may be different than actual product received.
|
394.94 |
|
|
March 1C-MD Mag-Drive Pump 115V
Applications for the 1C-MD Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.
March Pump's industrial 1C-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI). The 1C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless steel, and Ceramic Magnet. When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 0.25 inch male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1C-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.
Unit System 60Hz 50Hz Max Flow
3 GPM
9 LPM
Max Head
4.6 FT
1 M
Power
.005 HP
.003 KW
Electrical
115V 50/60HZ or 230V 50/60HZ
Submersible
Yes
Type
Centrifugal Mag Drive
Inlet
1/4"MPT
Outlet
1/4"MPT
Wet End
Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet
Uses
Submersible or Open Air
When submerged, the following is also in contact with the solution
Epoxy, Noryl, SJT Cord
|
317.85 |
|