4 Blade aluminum propeller for Mercury 8-9.9 horsepower engines and Nissan/Tohatsu 8-9.8 horsepower engines, both with 12 tooth spline and thru hub exhaust. 2-1/2" gear case.

4 Blade high thrust aluminum propeller for Yamaha 8 horsepower engines. Ideal for kicker/auxillary engines with heavy loads. 7 tooth spline and thru hub exhaust.

4 Blade aluminum propeller for Mercury 8-9.9 horsepower engines and Nissan/Tohatsu 8-9.8 horsepower engines, both with 12 tooth spline and thru hub exhaust. 2-1/2" gear case.

3 Blade aluminum propeller for 6-9.9 horsepower engines with 7 tooth spline and thru hub exhaust.

3 Blade aluminum propeller for 6-9.9 horsepower engines with 7 tooth spline and thru hub exhaust.

3 Blade aluminum propeller for 6-9.9 horsepower engines with 7 tooth spline and thru hub exhaust.

KingPin™ 7" x 7" Stainless Steel Square Base (Threaded) KingPin™ 7" L x 7" W Satin Stainless Steel Threaded Square Base with Nylon Bushing for 1-3/4" D Post (1630001) by Springfield Marine. Springfield Marine knows that comfort is important in marine seating. Whether behind the wheel for long passages in rough water; dropping a line in a quiet creek; or anywhere in between, Springfield Marine offers a wide range of configurations and options. Features: 7" x 7" stainless steel base, with nylon bushing and satin finish 4" cup depth below the deck Mount requires a 2-1/2" hole in the deck Built to provide secure, hassle-free boat seat mounting Specifications: Post Diameter: 1-3/4" Length: 7" Width: 7" Finish: Satin Material: Stainless Steel

King Pin 7" x 7" Base Plate Only This 7" x 7" base plate works with standard pin King Pin post applications. Specifications: Size (inch): 7" x 7"

5.25" AFT Leaning Mount for Searchlights & Thermal Cameras with 7" x 7" Base Plate Seaview 5" and 12" tall aft leaning mounts for thermal cameras and searchlights. Powder-coated brilliant white gives it a nice clean look and yet is very durable. Specifically designed for installations where space is very limited. The base for this mount is 7″ x 7″. Cable Management A hollow oval mast section provides plenty of room for cable management. Space-Saving Design The small 7"x 7" base footprint makes this a great solution to an installation where space is an issue. 

12" AFT Leaning Mount for Searchlights & Thermal Cameras with 7" x 7" Base Plate Seaview 5" and 12" tall aft leaning mounts for thermal cameras and searchlights. Powder-coated brilliant white gives it a nice clean look and yet is very durable. Specifically designed for installations where space is very limited. The base for this mount is 7″ x 7″. Cable Management A hollow oval mast section provides plenty of room for cable management. Space-Saving Design The small 7"x 7" base footprint makes this a great solution to an installation where space is an issue. 

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 Part # 0115-0064-0300 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ      230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet     Part # 0115-0064-0300  

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.   March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.      Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ          230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet

Dock Edge Dolphin Dockside Bumper 7" x 16" The ultimate in heavy impact protection Rugged, air filled Heavy-wall molded PVC & integral inflation valve Angled ends to deflect craft Use Straight bumpers in pairs to form inside corners Excellent gunnel protection Industrial Strength with the Standard Quality and Performance of Dolphin Fenders Product Specifications: Part No.: 1060-W-F Description: Dock-Side Dock Bumper, 7" x 16", White WARNING: This product can expose you to chemicals including Titanium dioxide,Vinyl Chloride which are known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Premium Impeller Kit - 39.7 x 12 x 19.2mm - 6 Blade - Pin Insert Replaces JMP 7000-01, Jabsco 22405-001, Johnson Pump 09-808B-1, Volvo Penta 875583. Specifications: Weight: 0.028 kg Dimensions: 39.7 mm x 12 mm x 19.2 mm Type: Copolymer Neoprene Original MC Blend Certification: ISO 9001 Quality Guaranteed

Premium Impeller Kit - 39.7 x 9.5 x 19.2mm - 6 Blade - Pin Insert Replaces JMP 7001-01, Jabsco 4528-0001, Johnson Pump 09-806B-1, Sherwood 9979K, Volvo Penta 803729, Yanmar 104211-42070. Specifications: Weight: 0.042 kg Dimensions: 39.7 mm x 9.5 mm x 19.2 mm Type: Copolymer Neoprene Original MC Blend Certification: ISO 9001 Quality Guaranteed