|
3 Blade aluminum propeller for 40, 50HP Johnson 4-stroke and 35-65 horsepower Suzuki. All with 13 tooth spline and thru hub exhaust. 3-1/4" gear case.
|
102.99 |
|
|
11" Wide x 12' Long Black Carpet Roll
11" wide covers a 2x4 or a 2x6 board
Marine grade carpet
Weather resistant
100% PET polyester
High quality
Durable backing
Minimal water retention
16.oz per square yard weight
Pile height 5/32"
|
26.20 |
|
|
11" Wide x 12' Long Blue Carpet Roll
11" wide covers a 2x4 or a 2x6 board
Marine grade carpet
Weather resistant
100% PET polyester
High quality
Durable backing
Minimal water retention
16.oz per square yard weight
Pile height 5/32"
|
20.83 |
|
|
11" Wide x 12' Long Grey Carpet Roll
11" wide covers a 2x4 or a 2x6 board
Marine grade carpet
Weather resistant
100% PET polyester
High quality
Durable backing
Minimal water retention
16.oz per square yard weight
Pile height 5/32"
|
20.83 |
|
|
Groco As-88-B 6 X 12 #316 Ss Enclosure
|
1363.44 |
|
|
Dock 2 Go Modular 6' x 12' Floating Dock Hardware Kit
The Dock 2 Go Modular Dock Kit includes all Heavy Duty Hot Dipped Galvanized mounting hardware required to assemble a 6' x 12' modular floating dock section. Each kit may be utilized to construct a stand-alone dock or may be attached to another Dock 2 Go section using a Dock 2 Go modular connector kit to increase dock length or width as required.
|
313.63 |
|
|
Marine Grip Tape - 6 x 12" - Black - 6 Pieces
Harken Marine Grip is a thin, reliable, nonabrasive grip tape that is more effective than adhesive alternatives, waxes and other products that reduces slipping. It also stands up to extreme marine conditions on boats, docks and stairs.
The superior grip is simple to install, clean and apply, and is cost-effective. And because it’s nonabrasive, it won’t damage clothing, wetsuits or skin. Harken Marine Grip is nonabsorbent, UV stable and good for all temperatures.
When compared, Harken Marine Grip outgrips other adhesive alternatives and waxes.
|
47.65 |
|
|
Marine Grip Tape - 6 x 12" - Grey - 6 Pieces
Harken Marine Grip is a thin, reliable, nonabrasive grip tape that is more effective than adhesive alternatives, waxes and other products that reduces slipping. It also stands up to extreme marine conditions on boats, docks and stairs.
The superior grip is simple to install, clean and apply, and is cost-effective. And because it’s nonabrasive, it won’t damage clothing, wetsuits or skin. Harken Marine Grip is nonabsorbent, UV stable and good for all temperatures.
When compared, Harken Marine Grip outgrips other adhesive alternatives and waxes.
|
47.65 |
|
|
Marine Grip Tape - 6 x 12" - Translucent White - 6 Pieces
Harken Marine Grip is a thin, reliable, nonabrasive grip tape that is more effective than adhesive alternatives, waxes and other products that reduces slipping. It also stands up to extreme marine conditions on boats, docks and stairs.
The superior grip is simple to install, clean and apply, and is cost-effective. And because it’s nonabrasive, it won’t damage clothing, wetsuits or skin. Harken Marine Grip is nonabsorbent, UV stable and good for all temperatures.
When compared, Harken Marine Grip outgrips other adhesive alternatives and waxes.
|
47.65 |
|
|
3 Blade aluminum propeller for 25-70 horsepower engines with 13 tooth spline and thru hub exhaust. 3-1/4" gear case.
|
114.99 |
|
|
3 Blade aluminum propeller for Yamaha 25-60 horsepower engines with 3-1/2" Gear Case and Honda 35-60 horse power engines with 3-1/4" Gear Case. Both 13 tooth spline and thru hub exhaust.
|
114.99 |
|
|
11'6" Drifter Fishing Inflatable Stand-Up Paddleboard Kit
11'6" x 34" x 6" Drifter SUP is a high-performance, oversized, large-capacity paddleboard designed for fishing. The SUP features a 6” core and 34" wide beam, making it suitable for a rider up to 350lbs. Equipped with Yak Attack base mount that supports fishing rod holders, cup holders & more (not included). Integrated front & rear bungee storage systems, bow mount, 5 stainless steel D-rings & 2 woven handles. D-ring placements allow for the attachment of kayak seats (not included). Two paddle straps are included that clip onto D-rings for a convenient holder for paddling while not in use. Printed fishing ruler on the adjustable touring-style paddle for convenient measuring.
Features:
Oversized large capacity paddleboard designed for fishing (350 lbs capacity)
34" extra wide beam for enhanced stability
Integrated front and rear bungee storage systems, bow mount, accessory base mount, 5 stainless steel D-rings, non-slip traction pad, 2 woven handles, and HR valve
D-ring placements allow for attachment of kayak seat (#29601 not included)
Technical Specifications:
Recommended pressure - 15 PSI
Backpack dimensions - 37" x 15" x 9"
Weight - 23.5 lbs
Weight Capacity - 350 lbs
In the Box:
SUP
Backpack
Adjustable paddle with a printed fishing ruler
Ankle leash
(2) paddle straps
Removable skeg
Pump with gauge
Repair kit
|
486.70 |
|
|
XKA Stainless Steel Trim Tab - 9 x 12
The Lectrotab stainless steel trim tab design provides unmatched strength and reliability. All stainless steel tabs are fabricated with a continuous rolled and pinned hinge. This design eliminates the need for welding.
Combined with a precision-engineered actuator, this kit is built to combine quiet operation with a non-hydraulic, maintenance free design. The unit is corrosion free, ensures very accurate tab positioning, provides maximum lift force, and is totally self-contained for easy installation. The actuator assembly is packaged in a non-metallic permanently sealed housing. No components need to be installed inside the boat.
Most importantly, unlike hydraulic trim tabs, there is no oil to leak out. The actuator incorporates either a standard or low profile transom mounting bracket.
*Control switch not included
Features:
Continuous rolled and pinned hinge provides added strength and eliminates the need for welding
Upper ram seal location cannot be damaged due to fouled ram or barnacle growth
Utilizes internal pressure equalization system
Internal brake system prevents unwanted tab movement when under way or backing down
Quiet operation
Actuators are fully load tested to push 1000 lbs of force
Non-metallic external structure which cannot corrode and will not deteriorate in the sun or under water
Technical Specifications:
Trim Tab Size (L x W) - 9" x 12" (23 x 30 cm)
Boat Length - 16' to 25' (5 to 7.5 M)
Trim Tab Material - 12 gauge, 304 Stainless Steel
Actuator DC Voltage - 12 V
Actuator Stroke Length - 2.25" (57 mm)
Actuator Cable Length - 23' (7 M)
Actuator Vertical Height - 11.875" (302 mm)
In the Box:
Two (2) Stainless Steel tabs
Two (2) actuators w/23' (7 M) cables
Instruction Manual
*Sold as an Individual
|
642.72 |
|
|
XKA Stainless Steel Trim Tab - 12 x 12
The Lectrotab stainless steel trim tab design provides unmatched strength and reliability. All stainless steel tabs are fabricated with a continuous rolled and pinned hinge. This design eliminates the need for welding.
Combined with a precision-engineered actuator, this kit is built to combine quiet operation with a non-hydraulic, maintenance free design. The unit is corrosion free, ensures very accurate tab positioning, provides maximum lift force, and is totally self-contained for easy installation. The actuator assembly is packaged in a non-metallic permanently sealed housing. No components need to be installed inside the boat.
Most importantly, unlike hydraulic trim tabs, there is no oil to leak out. The actuator incorporates either a standard or low profile transom mounting bracket.
*Control switch not included
Features:
Continuous rolled and pinned hinge provides added strength and eliminates the need for welding
Upper ram seal location cannot be damaged due to fouled ram or barnacle growth
Utilizes internal pressure equalization system
Internal brake system prevents unwanted tab movement when under way or backing down
Quiet operation
Actuators are fully load tested to push 1000 lbs of force
Non-metallic external structure which cannot corrode and will not deteriorate in the sun or under water
Technical Specifications:
Trim Tab Size (L x W) - 12" x 12" (30 x 30 cm)
Boat Length - 18' to 32' (5.5 to 9.5 M)
Trim Tab Material - 12 gauge, 304 Stainless Steel
Actuator DC Voltage - 12 V
Actuator Stroke Length - 2.25" (57 mm)
Actuator Cable Length - 23' (7 M)
Actuator Vertical Height - 11.875" (302 mm)
In the Box:
Two (2) Stainless Steel tabs
Two (2) actuators w/23' (7 M) cables
Instruction Manual
*Sold as an Individual
|
675.68 |
|
|
XKA Stainless Steel Trim Tab Kit with Rocker Switch - 9 x 12
The Lectrotab stainless steel trim tab design provides unmatched strength and reliability. All stainless steel tabs are fabricated with a continuous rolled and pinned hinge. This design eliminates the need for welding.
Combined with a precision-engineered actuator, this kit is built to combine quiet operation with a non-hydraulic, maintenance free design. The unit is corrosion free, ensures very accurate tab positioning, provides maximum lift force, and is totally self-contained for easy installation. The actuator assembly is packaged in a non-metallic permanently sealed housing. No components need to be installed inside the boat.
Most importantly, unlike hydraulic trim tabs, there is no oil to leak out. The actuator incorporates either a standard or low profile transom mounting bracket.
Lectrotab's new flat rocker switch has improved sealing to prevent water entry and recessed rocker to prevent breaking. Specially designed to provide and "instant stop" circuit when the switches are released, thus preventing actuator over-run.
Features:
Continuous rolled and pinned hinge provides added strength and eliminates the need for welding
Upper ram seal location cannot be damaged due to fouled ram or barnacle growth
Utilizes internal pressure equalization system
Internal brake system prevents unwanted tab movement when under way or backing down
Quiet operation
Actuators are fully load tested to push 1000 lbs of force
Non-metallic external structure which cannot corrode and will not deteriorate in the sun or under water
Technical Specifications:
Trim Tab Size (L x W) - 9" x 12" (23 x 30 cm)
Boat Length - 16' to 25' (5 to 7.5 M)
Trim Tab Material - 12 gauge, 304 Stainless Steel
Actuator DC Voltage - 12 V
Actuator Stroke Length - 2.25" (57 mm)
Actuator Cable Length - 23' (7 M)
Actuator Vertical Height - 11.875" (302 mm)
Rocker Switch Dimensions (W x H) - 3.125" x 3.25" (79.4 x 82.5 mm)
Rocker Switch Mounting Hole Cutout (H x W) - 2.25" x 2" (57.5 x 50 mm)
Rocker Switch Operating Voltage - 12 or 24 V
In the Box:
One (1) Flat Rocker Switch
Two (2) Stainless Steel tabs
Two (2) actuators w/23' (7 M) cables
Instruction Manual
*Sold as a Kit
|
745.73 |
|