Marine fuel lines and primer bulb meet or exceed EPA/CARB Fuel Permeation Regulations. Compounded tough, pliable UV-resistant hose promotes maximum fuel flow. Includes fittings built to OEM Specifications for replacement parts. Uses o-ring construction on all fittings for tight, leak-free connections. 3/8" hose. Clamshell packaged.

Marine fuel lines and primer bulb meet or exceed EPA/CARB Fuel Permeation Regulations. Compounded tough, pliable UV-resistant hose promotes maximum fuel flow. Includes fittings built to OEM Specifications for replacement parts. Uses o-ring construction on all fittings for tight, leak-free connections. 3/8" hose. Clamshell packaged.

Marine fuel lines and primer bulb meet or exceed EPA/CARB Fuel Permeation Regulations. Compounded tough, pliable UV-resistant hose promotes maximum fuel flow. Includes fittings built to OEM Specifications for replacement parts. Uses o-ring construction on all fittings for tight, leak-free connections. 3/8" hose. Clamshell packaged.

Yamaha fuel line assembly. Low permeation gasoline and solvent-resistant construction with stainless steel clamps and fittings. O-ring construction on all fittings for tight, leak-free connections. Primer bulb features dual internal check valves to ensure rapid prime and prevent back flow. 3/8" hose, 18-1/2" length on tank end, 55-1/2" length on motor end. Clamshell packaged.

SuproFlex Rub Rail Kit - White with Flex Chrome Insert - 2"H x 31/32"W x 80'L The SuproFlex Rub Rail Kit is lightweight and ultra-flexible to save you time and money while providing a seamless precision fit. The innovative SuproFlex series is co-extruded vinyl that provides two levels of hardness – ensuring enhanced protection from impact. SuproFlex Rub Rail requires minimal heating – reducing installation time and manpower. Additionally, SuproFlex Rub Rail requires no pre-forming and easily molds to most hull shapes.  Features: Ideal for boats up to 65' Co-extruded to provide two levels of hardness Rigid backing and soft durometer front Shock-absorbing channels for higher impact resistance Lighter weight than traditional vinyl rub rail Requires no pre-forming and minimal heating Pairs with V12-0307CP (included in kit) Made in the USA 5-year limited warranty

SuproFlex Rub Rail Kit - Black with Flex Chrome Insert - 2"H x 1.2"W x 80'L The SuproFlex Rub Rail Kit is lightweight and ultra-flexible to save you time and money while providing a seamless precision fit. The innovative SuproFlex series is co-extruded vinyl that provides two levels of hardness – ensuring enhanced protection from impact. SuproFlex Rub Rail requires minimal heating – reducing installation time and manpower. Additionally, SuproFlex Rub Rail requires no pre-forming and easily molds to most hull shapes.  Features: Ideal for boats up to 65' Co-extruded to provide two levels of hardness Rigid backing and soft durometer front Shock-absorbing channels for higher impact resistance Lighter weight than traditional vinyl rub rail Requires no pre-forming and minimal heating Pairs with V12-0307CP (included in kit) Made in the USA 5-year limited warranty

SuproFlex Rub Rail Kit Gray with Gray Insert - 2"H x 1.2"W x 80'L The SuproFlex Rub Rail Kit is lightweight and ultra-flexible to save you time and money while providing a seamless precision fit. The innovative SuproFlex series is co-extruded vinyl that provides two levels of hardness – ensuring enhanced protection from impact. SuproFlex Rub Rail requires minimal heating – reducing installation time and manpower. Additionally, SuproFlex Rub Rail requires no pre-forming and easily molds to most hull shapes. Features: Ideal for boats up to 65' Co-extruded to provide two levels of hardness Rigid backing and soft durometer front Shock-absorbing channels for higher impact resistance Lighter weight than traditional vinyl rub rail Requires no pre-forming and minimal heating Predrilled for fasteners Pairs with V12-0307GRD gray insert (included in the kit) Made in the USA 5-year limited warranty

Pontoon Curved Corner-Gard - 3"W x 12"L This unique Corner-Gard offers a level of protection to areas on the Pontoon boat other fenders or bumpers can't provide. The Pontoon Corner-Gard comes shaped to mount on either a radius style or 90o pontoon corners. The Corner-Gard mounts over the original factory installed aluminum corner section to provide air-cushioning impact protection when docking. Special silver PVC formulated to match the aluminum color of the boat and secures with the included stainless fasteners.  Specifications: Dimensions: 3"W x 12"L Mounting hardware included

Magnesium Hull Plate Anode 8-3/8" x 4-1/32" x 1-1/16" Specifications: Magnesium Hull Plate 1.80lbs

3/8" x 50' Boxed Low Permeation Type A1-15 Fuel Line Hose - Black Trident Barrier Lined A1-15 Fuel Hose for both gasoline (including ethanol blends up to 85%) and diesel (including bio diesel blends up to B100). This hose is built with the best fuel, fire, and age-resistant formulation, and a unique "Barrier Liner" on the inside surface of the tube, so fuel is not in direct contact with rubber. Features:  Provides extraordinary resistance to fuel permeation, aging, and also to fire, heat, cold, and the ozone  Also provides excellent bend-ability NMMA Type Accepted & CE certified Application: Marine Fuel Hose (distribution, return, vent and transfer) For all marine fuels including gasoline, alcohol blends (CE-10), diesel and bio-diesel Construction: Tube: Nylon Internal Barrier, NBR  Cover: NBR/PVC Blend  Reinforcement: Polyester 2 spiral  Temperature Range: -20°F to 212°F (-28ºC to 100ºC)  Length: 50 ft. (15 m) Boxed Specifications: Inner Diameter: (inch) 3/8" / (mm) 9.50 Outer Diameter: (inch) 0.681 / (mm) 17.3 Burst Pressure: (psi) 400 / (mpa) 2.76 Working Pressure: (psi) 100 / (mpa) 0.69 Bend Radius: (inch) 2" / (mm) 50.8 Weight: (lb/100 ft.) 15.6 / (kg/m) 0.233 Permeation Rate: <10 (Standard is 10g/m2/24 hrs (CE10) *The #365 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, USCG Type A1-15; CARB Executive Order RM-17-008 and EPA Certified low permeation Type A1-10

3/8" x 50' Boxed Barrier Lined B1-15 EPA Compliant Outboard Fuel Line Hose - Gray This hose is built with the best fuel and age-resistant formulations and a unique "Barrier Liner" on the inside surface of the tube, so the fuel is not in direct contact with rubber. This greatly reduces fuel permeation and prevents ethanol degradation of the rubber tube, which can cause small pieces of rubber to reach and damage the engine. That is particularly important considering the prospect of higher ethanol blends (E-15) available at gas stations next year.  Features:  Provides extraordinary resistance to fuel permeation, aging, heat, cold, and ozone   Also, provides excellent rope-like bend-ability and fitting retention For both gasoline (including ethanol blends up to E85) and diesel (including bio diesel blends up to 100%) EPA Certified and CARB Executive Order for low permeation Type B1-15 NMMA Type Accepted & CE certified Application: Marine Fuel Hose for distribution, return, vent and transfer For all marine fuels including gasoline, alcohol blends (CE-10), diesel and bio-diesel Construction: Tube: Fluoroplastic Internal Barrier Cover: Gray CPE Rubber Reinforcement: 2-Spiral Polyester Plies  Temperature Range: -20°F to 212°F (-28ºC to 100ºC) Length: 50’ (15m) Boxed Specifications: Inner Diameter: (inch) 3/8" / (mm) 9.50 Outer Diameter: (inch) 0.588 / (mm) 14.9 Burst Pressure: (psi) 175 / (mpa) 1.21 Working Pressure: (psi) 35 / (mpa) 0.24 Bend Radius: (inch) 4" / (mm) 101.6 Weight: (lb/100 ft.) 10.5 / (kg/m) 0.156 Permeation Rate (Standard is (15g/m^2/24hrs (CE10)): 5.0 *The #305 series exceeds ABYC H-24, SAE J1527, ISO 8469 B1, USCG Type B1-15

3/8" x 15' Nylon Double Braid Dock Line - Grey  Double Braid Nylon has superb handling and is the perfect combination of high-grade marine nylon, special torque-balanced construction, and a unique stabilization process, which produces this long-wearing line that resists kinking. Applications: Dock line - ≤55' (16.8 M) vessel Mooring line - ≤ 30' (9.1 M) vessel  Technical Specifications: Color: Grey Material: Double braid nylon  Rope Diameter: 3/8"  Rope Length: 15' Tensile Strength: 13,100 lb *Sold as an Individual

3/8" x 25' Nylon Double Braid Dock Line - Grey  Double Braid Nylon has superb handling and is the perfect combination of high-grade marine nylon, special torque-balanced construction, and a unique stabilization process, which produces this long-wearing line that resists kinking. Applications: Dock line - ≤55' (16.8 M) vessel Mooring line - ≤ 30' (9.1 M) vessel  Technical Specifications: Color: Grey Material: Double braid nylon  Rope Diameter: 3/8"  Rope Length: 25' Tensile Strength: 13,100 lb *Sold as an Individual

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 Part # 0115-0064-0300 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ      230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet     Part # 0115-0064-0300  

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.   March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.      Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ          230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet