BURKS 5808, PACKING RING

BURKS 21000, BEARING

BURKS 21463, BEARING

BERKELEY S13435, SET OF PACKING RINGS

BERKELEY S13469, SET OF PACKING RINGS

BERKELEY S15094, SET OF PACKING RINGS

Oberdorfer 5479 Packing Ring  

Oberdorfer 5481 Packing Ring  

Oberdorfer 7558 Ss Packing Ring  

Jabsco 24031-0001 Pack Ring  

BURKS 20522-9-MV REPAIR KIT FOR CS9MV Pumps The Burks 20522-9-MV is a repair kit for all CS9MV series pumps with Viton seal, comes with the impeller, raceway, Viton shaft seal, Viton o-ring gasket, suction sleeve, raceway screws, impeller locknut, shaft key and instructions.   There is a 6 to 8 week Lead Time from time of order.

BURKS 09632-D, WEAR RING

BURKS 10CS5M, Turbine Pump 32.5 gpm 115/230v Burks close coupled 32.5 gpm turbine pump having 1-1/4" NPT inlet size and 1" NPT outlet size features 350 ft Maximum Head and maximum suction lift and 1 hp power rating.   Burks exclusive unique regenerative type turbine pumps are designed to handle clear water and many other non-abrasive, lower viscosity liquids on high pressure, low capacity applications with the greatest possible efficiency. Compact space saving size No coupling - eliminates misalignment problems Dependable carbon ceramic mechanical shaft seal for temperatures to 225 deg F (107 deg C) Bronze impeller with monel blades - the only moving part Bronze raceway with cast-in vortex pockets - will not vapor lock 303 stainless steel pump shaft Easy to service Every pump factory tested

BURKS 20CS6M Close Coupled Turbine Pump BURKS exclusive unique regenerative type turbine pumps. Designed to handle clear water in addition to and many other non-abrasive, lower viscosity liquids on high pressure. As well as low capacity applications with the greatest possible efficiency.   BURKS is the only turbine pump with Life-Lok® External Impeller Adjustment. This feature allows re adjustment of impeller without disturbing piping, disassembling pump or replacing parts. This, as a result, gives up to 40% longer service life than turbine pumps of other designs.   Self-Priming Pump Compact and Space-saving size No coupling so this eliminates misalignment problems Dependable carbon/ceramic mechanical shaft seal for same temperatures to 225 °F (107° C). Bronze impeller with Monel blades, therefore the only moving part Bronze raceway with cast-in vortex pockets – will not vapor lock #303 Stainless Steel pump shaft Every pump is factory tested     Motor Information 4CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 1750 RPM and therefore Three Phase motors are 208-230/460 Volts, 60/50 Hz, 1750/1450 RPM.     CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 3450 RPM Three Phase 1, 11/2 & 2HP. – 208-230/460 Volt, 60/50 Hz., 3450/2900 RPM Three Phase 3 & 5 HP – 208-230/460 Volt, 60 Hz, 3450 RPM Standard pump motors have open drip proof construction and are rated with jet pump service factors for continuous duty operation at all ratings shown. Single phase motors are capacitor start/induction run with built-in overload protection. Three phase motors require a magnetic type starter which provides full 3-leg overload protection. Failure to use the correct starter and overloads will void the warranty.   High Temperature   For Temperatures to 500 °F (260 °C). Series CS Pumps are available while in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications. This feature greatly extends seal life in high temperature applications. 

BURKS 21546, O'RING VITON