BURKS 350CS9M-FE, TURBINE PUMP 230/460v 3PH 5HP Turbine Pump and Motor unit. Bronze Fitted Cast Iron Construction.  Close Coupled to a 5 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet. OEM version with FE Franklin Electric Motor.

BURKS 320CS6M, TURBINE PUMP 230/460V 3PH 2HP Bronze Fitted Cast Iron Construction. Close Coupled to a 2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.   Please Contact us for a shipping quote http://www.clrmarine.com/Contact_Us

BURKS 320CS7M, TURBINE PUMP 230/460v 3PH 2HP All BRONZE Construction. Close Coupled to a 2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.   Please Contact us for a shipping quote http://www.clrmarine.com/Contact_Us

BURKS 350G6-1 1/2, Centrifugal Pump 230/460v 3PH 5HP Bronze Fitted Cast Iron Construction.  Close Coupled to a 5 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.  Ports are 2 Inches NPT Inlet, 1-1/2 Inches NPT Outlet. Impeller Diameter is 5.88 Inches.   UNSPSC Code: 40150000  

BURKS T350G6-1 1/2, CENTRIFUGAL PUMP 3PH 5HP TEFC Close Coupled, 60 Hz, Three Phase, 3500 RPM, 5 Horsepower, TEFC Motor Enclosure, Frame Size 184JM   UNSPSC Code: 40150000

BURKS 315CS6M TURBINE PUMP 230/460 Volts 1.5HP All BRONZE Construction.  Close Coupled to a 11/2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.     Self-Priming Pump Compact and Space-saving size No coupling so this eliminates misalignment problems Dependable carbon/ceramic mechanical shaft seal for same temperatures to 225 °F (107° C). Bronze impeller with Monel blades – therefore the only moving part Bronze raceway with cast-in vortex pockets – will not vapor lock #303 Stainless Steel pump shaft Easy to service as a result Especially relevant, Every pump factory tested   Motor Information 4CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 1750 RPM and Three Phase motors are 208-230/460 Volts, 60/50 Hz, 1750/1450 RPM.   CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 3450 RPM Three Phase 1, 11/2 & 2HP. – 208-230/460 Volt, 60/50 Hz., 3450/2900 RPM Three Phase 3 & 5 HP – 208-230/460 Volt, 60 Hz, 3450 RPM Standard pump motors have open drip proof construction and are rated with jet pump service factors for continuous duty operation at all ratings shown. Single phase motors are capacitor start/induction run with built-in overload protection. Three phase motors require a magnetic type starter which provides full 3-leg overload protection. Failure to use the correct starter and overloads will void the warranty.   High Temperature For Temperatures to 500 °F (260 °C). Series CS Pumps are available while in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications.    For High Temp Models please use the Contact Us page, also use the Contact Us page for a Shipping Quote.      

Laing SM-909-NT-14, Mag-Drive Centrifugal Pump Laing Mag-Drive Centrifugal Pump Plastic, 7GPM at 4' Head, 14' Head Max, 230V 60HZ 1/50HP 65Watts, 3/4”MNPT Ports

Scot Pump 35065 MPU AB 1-1/4 X 1 1/2 HP TEFC Pump • All Bronze marine centrifugal pump Freshwater or seawater applications • Precision machined to close tolerances for consistent performance. • Hardware - Type 303 stainless steel • Semi-open impeller handles solids • Impeller mounted on motor shaft • Heavy-duty, designed for continuous 24 hour – 7 day operation. • Stainless steel shaft.   Shaft Seal • Rated at 75 PSI – 5 BAR • Seawater Buna rubber parts, ceramic stationary and carbon rotating element, stainless steel spring and metal components   Motor - 2 Pole • Totally enclosed fan cooled IP-44 motors meet marine, European, and Coast Guard ignition protected requirements. • Sealed ball bearings • Single-phase capacitor start 60 Hz – 115/230 Volt • Dual frequency 50 Hz or 60 Hz motors are available • Three phase motors are not available 

Applications for the MDX-3-1/2 Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.    March Pump's industrial MDX-3-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 8 gallons per minute at 1 foot, and its maximum head is 19 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, carbon filled Kynar (PVDF), Ryton Buna N, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheitor 87 Celsius. The March MDX-3-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 8.5 GPM 30 LPM Max Head 19 FT 4 M Power .04 HP .029 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front Housing and Impeller), Carbon filled Kynar (Rear Housing, Shaft), Ryton (Thrust Washer), Buna N (O-Ring), Stainless Steel (Screw) Ceramic Magnet    

March 1A-MD-1/2 Mag Drive Pump March Pump's industrial 1A-MD-1/2 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1A-MD-1/2 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 1/2 inch smooth, and the outlet is 1/2 inch smooth. The standard motor is a 1 Phase 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-1/2 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals. To determine if the March 1A-MD-1/2 is suitable for your application, please contact March Pump.   Perfect for Applications Including Applications for the 1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   Great for Chemicals Including The 1A-MD-1/2 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.   Inlet: 1/2"OD Outlet: 1/2"OD Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft) Uses:Submersible or Open Air When submerged, the following is also in contact with the solutionEpoxy, Noryl, SJT Cord   P/N 0115-0007-0700 (230V)

March 1A-MD-1/2 Mag Drive Pump March Pump's industrial 1A-MD-1/2 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1A-MD-1/2 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 1/2 inch smooth, and the outlet is 1/2 inch smooth. The standard motor is a 1 Phase 115V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-1/2 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals. To determine if the March 1A-MD-1/2 is suitable for your application, please contact March Pump.   Perfect for Applications Including Applications for the 1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   Great for Chemicals Including The 1A-MD-1/2 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.   Inlet: 1/2"OD Outlet: 1/2"OD Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft) Uses:Submersible or Open Air When submerged, the following is also in contact with the solutionEpoxy, Noryl, SJT Cord   P/N:0115-0007-0200 (115V)

BURKS 350CS8M, TURBINE PUMP 230/460v 5HP 3PH Bronze Fitted Cast Iron Construction.  Close Coupled to a 5 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.  Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000

March 0155-0174-1000 Motor 3Ph 1Hp 230/460V Tefc

BURKS 09812F, MOTOR 3PH 3HP ODP CS

March 0155-0022-1000 Motor Only Totally Enclosed Fan Cooled Electric Motor 3Ph 208/230/460V 50/60HZ 3/4HP 56Fr for all March 7 Series Pumps