SailPod Uncut Usable Face 15.18″w x 9.85″h (38.6cm w x 25cm h) for Garmin GPSMAP® 1223/1243xsv - 9.5″ Wide Guard SailPods are for mounting a single Radar or Chartplotter at the helm. Navigation at your fingertips… “Where you need it when you need it.” SailPods are the smart solution for mounting your Radar or Chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. NavPods have a high gloss finish, giving you a clean mounting solution while concealing unsightly wires. Nickel Chrome-Plated tamper-resistant screws provide a little bling and a lot of security. Designed with a double gasket waterproof seal, NavPods protect your electronics from the harshest of wet offshore boating conditions. A SailPod is best mounted on a Single Bend AngleGuard, or on the angled section of a Double Bend Angle Guard with an InstrumentPod mounted above it on the straight section. Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All SailPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection for your Marine Electronics. SailPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a “compression set” like many rubber compounds. This is important when you need to open the SailPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.

PED5200 PedestalPod Uncut (Usable Face = 15.18"W x 9.85"H) (38.6cm W x 24.9cm H) - Carbon Black PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your fishfinder/chartplotter from the harshest of wet boating conditions. PedestalPods provide the convenience of easily reaching and controlling the fishfinder/chartplotter while providing added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20" off the deck and located near the bow and at the 45° angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal keeping spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics.  Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the NavPod. The heavy duty, powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look and provides protection for wires and electrical connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. There are pre-cut models available for 7", 9" and 12" LCD displays from all major marine electronic manufacturers.

PP5200 PowerPod Uncut (Usable Face = 15.18"W x 9.85"H) (39.6cm W x 24.9cm H) - Carbon Black PowerPods are designed for the serious boater who is blasting offshore. He demands the most from his boat and his electronics. He needs a tough and rugged mount to protect vital electronics from the harshest of offshore boating conditions. Sturdy and secure, yet clean and attractive, PowerPods are better than bracket mounting. Over 70 Pre-Cut PowerPods are available for all popular manufacturers products. 1.8" opening in the swivel tube provides plenty of room for running wires and connectors through. PowerPods are positioned at a 20 degree tilt back viewing angle. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. Structural Rigidity The Gen3 enhancements now include a thicker gauge Acrylic Capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the Acrylic is combined with the durability of the ABS. The Acrylic cap protects the ABS from UV and it's potentially damaging effects on plastic. These NavPods are really strong! Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poran Microcell Polyurathane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.  Nickel Chrome Plated Stainless Steel NavPod uses all 316 stainless steel hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. For Gen3 NavPods we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! Commitment to Quality We are committed to producing high quality Waterproof Housings for Marine Electronics. We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods. We want you to be a NavPod customer for life and are willing to earn your trust and loyalty.

PowerPod Un-Cut (Usable Face = 18.36″W x 10.61″H) (46.6cm W x 26.9cm H)  PowerPods are better than bracket mounting. Sturdy and secure, yet clean and attractive, PowerPods position your fishfinder/chartplotter at a 20-degree viewing angle. PowerPods provide the clean look of flush mounting with the advantages of a swivel base. PowerPods are now available in two color options. All models are available in high gloss white, and many models (PP4400-C, PP4500-C, PP4600-C, PP4800-C, PP4900-C, PP5050-C, PP5100-C, PP5200-C, PP5920-C Series) are also available in black carbon print. Constructed out of durable ABS like all Gen3 NavPods, these new black carbon models have the same high gloss finish with UV stability. NavPods are made to protect your marine electronics from the harshest of wet boating conditions. All NavPods are manufactured with a double gasket system that provides an excellent watertight seal. PowerPods keep the spray off the electrical connections on the back of your fishfinder/chartplotter, assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the PowerPod. The base has a large opening (1.1″ for PP4100, PP4400, PP4500, PP4600 Series; 1.8″ for PP4800, PP4900, PP5030, PP5050, PP5060, PP5100, PP5200, PP5920 models) to provide plenty of room for running wires and connectors through the base to conceal them from the elements. This provides protection for wires and connectors from water intrusion, UV exposure, or damage from getting snagged and ripped out of their sockets. All NavPods come with a security wrench and Nickel Chrome-Plated Stainless Steel tamper-resistant screws for a little bling and a lot of security. PowerPod pre-cut models are available for most 7″, 9″, 12″ and 16″ displays from all major marine electronic manufacturers. NavPod backs up its commitment to quality by offering a 10-year warranty on all Gen3 NavPods. PowerPods: Protection, Convenience, Security.

SailPod Pre-Cut for Garmin GPSMAP® 1223, 1223xsv, 1243 & 1243xsv for 12″ Wide Guard SailPods are for mounting a single Radar or Chartplotter at the helm. Navigation at your fingertips… “Where you need it when you need it.” SailPods are the smart solution for mounting your Radar or Chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. NavPods have a high gloss finish, giving you a clean mounting solution while concealing unsightly wires. Nickel Chrome-Plated tamper-resistant screws provide a little bling and a lot of security. Designed with a double gasket waterproof seal, NavPods protect your electronics from the harshest of wet offshore boating conditions. A SailPod is best mounted on a Single Bend AngleGuard, or on the angled section of a Double Bend Angle Guard with an InstrumentPod mounted above it on the straight section. Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All SailPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection for your Marine Electronics. SailPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a “compression set” like many rubber compounds. This is important when you need to open the SailPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.

SystemPod Pre-Cut for Garmin GPSMAP® 1223, 1223xsv, 1243 & 1243xsv on Right & 2 Instruments (3.6″ holes) on Left for 9.5″ Wide Guard GP1170-25 for Sail: SystemPod Pre-Cut for Garmin GPSMAP 1223/1223xsv/1243/1243xsv on the right AND two instruments (3.6″ holes) on the left for 9.5″ wide guard  SystemPods are for mounting a Radar or Chartplotter and Instruments together at the helm. Navigation at your fingertips… “Where you need it when you need it.” SystemPods are the smart solution for mounting your Radar or Chartplotter and Instruments together at the helm where you can easily operate and clearly see the fine details of the screen. This SystemPod for Power can be dash mounted using the SK135 Stanchion Kit, or overhead mounted using the SK129 Stanchion Kit. Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All SystemPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection for your Marine Electronics. SystemPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a “compression set” like many rubber compounds. This is important when you need to open the SystemPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. For Gen3 NavPods we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little style! Commitment to quality We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.

PP5200-20 PowerPod Pre-Cut for Garmin GPSMAP® 1223, 1223xsv, 1243 & 1243xsv PowerPods are better than bracket mounting. Sturdy and secure, yet clean and attractive, PowerPods position your fishfinder/chartplotter at a 20-degree viewing angle. PowerPods provide the clean look of flush mounting with the advantages of a swivel base. PowerPods are now available in two color options. All models are available in high gloss white, and many models (PP4400-C, PP4500-C, PP4600-C, PP4800-C, PP4900-C, PP5050-C, PP5100-C, PP5200-C, PP5920-C Series) are also available in black carbon print. Constructed out of durable ABS like all Gen3 NavPods, these new black carbon models have the same high gloss finish with UV stability. NavPods are made to protect your marine electronics from the harshest of wet boating conditions. All NavPods are manufactured with a double gasket system that provides an excellent watertight seal. PowerPods keep the spray off the electrical connections on the back of your fishfinder/chartplotter, assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the PowerPod. The base has a large opening (1.1″ for PP4100, PP4400, PP4500, PP4600 Series; 1.8″ for PP4800, PP4900, PP5030, PP5050, PP5060, PP5100, PP5200, PP5920 models) to provide plenty of room for running wires and connectors through the base to conceal them from the elements. This provides protection for wires and connectors from water intrusion, UV exposure or damage from getting snagged and ripped out of their sockets. All NavPods come with a security wrench and Nickel Chrome-Plated Stainless Steel tamper-resistant screws for a little bling and a lot of security. PowerPod pre-cut models are available for most 7″, 9″, 12″ and 16″ displays from all major marine electronic manufacturers. NavPod backs up its commitment to quality by offering a 10-year warranty on all Gen3 NavPods. PowerPods: Protection, Convenience, Security.

GP1201 SailPod Pre-Cut for Garmin 1020 / 1020xs / 1040xs for 9.5" Wide Guard GP1200 Series for 9.5" Guard, SailPods for Sail are for mounting a single radar or chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. A single SailPod is best mounted on a Single Bend AngleGuards or use a Double Bend AngleGuards to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications. Sizing: Overall Size: 11.3"H x 16.5"W x 5.55"D Usable Face: 9.85"H x 15.18"W x 4.25"D Max Cutout:9"H x 14.25"W All SailPods include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners and wrench Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

GP2055 SailPod f/Garmin GPSMAP 5012 & 5212 for 12" Guards NavPod Protects Your Electronics In Harsh Conditions Grand Prix series outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability. Polished stainless steel tamperproof fasteners. NavPod allows you to place your electronics within reach. Dimensions (15.125"w x 10.88"h x 6.125"d).

SailPod for Garmin 4010/4210 on 9.5" wide guard Grand Prix series outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability. Polished stainless steel tamperproof fasteners. NavPod allows you to place your electronics within reach. Dimensions (15.125"w x 10.88"h x 6.125"d)

Pre-Cut for Garmin 4010/4210 on 12" wide guard NavPod Protects Your Electronics In Harsh Conditions Grand Prix series outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability. Polished stainless steel tamperproof fasteners. NavPod allows you to place your electronics within reach. Dimensions (15.125"w x 10.88"h x 6.125"d).

Pre-Cut for Garmin 6008/6208 on 9.5" wide guard NavPod Protects Your Electronics In Harsh Conditions Grand Prix series outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability. Polished stainless steel tamperproof fasteners. NavPod allows you to place your electronics within reach. Dimensions (15.125"w x 10.88"h x 6.125"d).

GP1200 SailPod Uncut for 9.5" Wide Guard GP1200 Series for 9.5" Guard, SailPods for Sail are for mounting a single radar or chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. A single SailPod is best mounted on a Single Bend AngleGuards or use a Double Bend AngleGuards to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications. Sizing: Overall Size: 11.3"H x 16.5"W x 5.55"D Usable Face: 9.85"H x 15.18"W x 4.25"D Max Cutout:9"H x 14.25"W All SailPods include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners and wrench Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

GP1202 SailPod Pre-Cut for Simrad NSS12 evo2 or B&G Zeus² 12 for 9.5" Wide Guard GP1200 Series for 9.5" Guard, SailPods for Sail are for mounting a single radar or chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. A single SailPod is best mounted on a Single Bend AngleGuards or use a Double Bend AngleGuards to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications. Sizing: Overall Size: 11.3"H x 16.5"W x 5.55"D Usable Face: 9.85"H x 15.18"W x 4.25"D Max Cutout:9"H x 14.25"W All SailPods include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners and wrench Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

GP1204 SailPod Pre-Cut for Raymarine a125 / a127 / a128 for 9.5" Wide Guard GP1200 Series for 9.5" Guard, SailPods for Sail are for mounting a single radar or chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. A single SailPod is best mounted on a Single Bend AngleGuards or use a Double Bend AngleGuards to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications. Sizing: Overall Size: 11.3"H x 16.5"W x 5.55"D Usable Face: 9.85"H x 15.18"W x 4.25"D Max Cutout:9"H x 14.25"W All SailPods include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners and wrench Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets