MM-8G Mix & Match Cable for 600W Non-CHIRP Transducers Mix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable. The short pigtail attached to the transducer ends in an Airmar 5-pin female connector. The adapter cables have a matching Airmar 5-pin male connector (shown below) at one end and the correct connector for a specific brand of electronics at the other end. Both parts are needed for installation. If the user changes equipment brand at some later time, the transducer can be left in place and the adapter cable replaced. Mix and Match 600W transducers include the B117, B45, B60, P319, P66*, P79, SS505, and SS60. (* not all models) A 12m (40') extension cable (part MM-5P-5P) is available with one male and one female 5-pin connector. Note that 600W Mix and Match cables cannot be used with 1kw transducers. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Navico Mix & Match Cable for Low-Frequency CHIRP Transducers - 9-Pin Specifically for use with Airmar's Mix and Match CHIRP transducers up to 1kW (1,000W). This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Furuno 10-Pin Mix & Match Cable for Low Frequency CHIRP Transducers Features: 10-Pin For Low Frequency CHIRP Transducers This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

11-Pin Low-Frequency Mix & Match Cable for Raymarine Some CHIRP transducers are now made as Mix and Match models. These versions have a common base transducer with an attached 9-meter cable, plus an interchangeable short (1-meter) brand-specific adapter cable. The permanently-attached 9-meter cable ends in an Airmar 12-pin connector. This cable is run up through the boat to the equipment location. The short adapter cable connects to the transducer cable at one end and to the equipment at the other end. Both parts are needed for an installation. If the user changes equipment brand at some later time, the transducer and its attached cable can be left in place and only the adapter cable needs to be replaced. Note that CHIRP Mix and Match cables cannot be used with conventional 50/200kHz transducers. The same cables are used for all CHIRP transducers irrespective of their power rating. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Garmin 8-Pin Mix & Match Cable for Low-Frequency CHIRP 1kW Transducers Airmar's 8-Pin Mix & Match Chirp Cable specifically for Garmin. Features: 8-Pin Low-Frequency CHIRP Cable   This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Garmin 12-Pin Mix & Match Cable for Chirp Transducers Airmar's Garmin Mix & Match Cable Features: 12-Pin Specifically for Chirp Transducers This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Navico 9-Pin Dual Mix & Match Cable for Dual Element Transducers For dual-socket Navico/Lowrance/Simrad xSonic 9-pin equipment Mix and Match Cables for CHIRP Transducers Many CHIRP transducers are now made as Mix and Match models. These versions have a common base transducer with an attached 9-meter cable, plus an interchangeable short (1-meter) brand-specific adapter cable. The permanently-attached 9-meter cable ends in an Airmar 12-pin connector. This cable is run up through the boat to the equipment location. The short adapter cable connects to the transducer cable at one end and to the equipment at the other end. Both parts are needed for an installation. If the user changes equipment brand at some later time, the transducer and its attached cable can be left in place and only the adapter cable needs to be replaced. Note that CHIRP Mix and Match cables cannot be used with conventional 50/200kHz transducers. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Furuno 12-Pin Mix & Match Cable for CHIRP Dual Element Transducers For use with Airmar's Mix and Match CHIRP transducers up to 1kW (1,000 watts). This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Furuno 10-Pin Mix & Match Cable for High or Medium Frequency CHIRP Transducers Features: 10-Pin For High or Medium Frequency CHIRP Transducers This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B265LM Bronze Chirp Thru-Hull Transducer 1kW with Fairing Block - Mix & Match Cable Needed The B265LM Chirp-ready transducer is the perfect mid-range to deep performing transducer in the Airmar line. Covering a huge bandwidth, the frequency performance on many species delivers crisp, clear target separation. This 1 kW powerhouse transducer delivers extreme target detail, bottom discrimination, and bait and game fish separation at all depths. The included High-Performance Fairing will give you broadband performance at speeds over 30 knots (34 MPH). We will leave it up to you to discover the rest of the secrets that can be unlocked with tunable, Chirp Broadband Transducer Technology. LM Model - Low Frequency 42-65 kHz/Medium Frequency 85-135 kHz  Features: Depth & fast-response water-temperature sensor 1kW power for excellent deep to mid-depth performance Low frequency: 42 kHz to 65 kHz 25° to 16° beamwidth (port-starboard) Maximum depth 3000' (914 m) Medium frequency: 85 kHz to 135 kHz 16° to 11° beamwidth Maximum depth 1500' (457M) 73 kHz of total bandwidth from one transducer Covers popular fishing frequencies of 50, 88, and 107 kHz plus everything else in the bandwidths Bronze transducer housing with High-Performance Fairing for improved high speed performance Recommended boat size: 8 m (25') and above Hull Type: Fiberglass or wood Models also available in Transom Mount (TM265LM), Pocket Mount (PM265LM), Cavity Mount (CM265LM), In-Hull (M265LM) Exclusive Xducer ID® technology Specifications: Hull Deadrise: Up to 20° with fairing Acoustic Window: Urethane Weight: 7.3 kg (16 lb) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B75H Bronze Chirp Thru Hull 12° 600W Requires Mix & Match Cable Rely on Airmar’s broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town!  Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 80 kHz of total bandwidth in just one installation, saving customers time and money. Features: 12° 600W Needs Mix & Match Cable This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

TM185C-HW-MM CHIRP Transducer Transom Mount Needs Mix & Match Cable Get more coverage under the boat with Airmar's wide beam Chirp. Offering a high frequency range of 150-250 kHz and a constant 25° Beamwidth, this transducer is truly broadband at its best. In addition to improving the performance of Chirp-ready echosounders, anglers using this wide beam transducer will achieve twice the coverage under the boat compared to our current high frequency Chirp transducers. A unique property of the high frequency transducers is that the Beamwidth is a constant 25° angle across the entire frequency band. Now, in addition to providing vast bottom coverage and precise fish detection in the upper water column that can sometimes go unseen with our narrow beam transducers, Airmar's wide beam format also creates crisper and larger return images on the display. Features: CHIRPS across the following bandwidths: — High-Frequency: 150-250 kHz 25° Constant Beamwidth 1kW (1,000 Watt) RMS Power Depth Range: 600'-800' Depth & fast-response water-temperature sensor Urethane housing and stainless steel kick-up mounting bracket Boat Size: 8 m to 12 m (25' to 40') Boat Type: Outboards; I/O Hull Type: Fiberglass, Wood, Metal Can retrofit to existing TM258, TM260, TM265, and TM275 bracket Needs Mix & Match Cable This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B275C-LHW Bronze Thru-Hull - Low & High Wide Frequency Requires Mix & Match Cable Get more coverage under the boat with Airmar's wide beam CHIRP product line. Offering a high frequency range of 150-250 kHz and a constant 25° beam width, these transducers are truly broadband at its best. In addition to improving the performance of CHIRP-ready echosounders, anglers using the new wide beam transducers will achieve twice the coverage under the boat compared to our current high frequency CHIRP transducers. A unique property of the high frequency transducers is that the beambwidth is a constant 25° angle across the entire frequency band. Now, in addition to providing vast bottom coverage and precise fish detection in the upper water column that can sometimes go unseen with our narrow beam transducers, Airmar's wide beam format also creates crisper and larger return images on the display. We've got you covered! Features: Depth & Temperature 42-65 kHz L Frequency 150-250 kHz H Frequency Bronze 1 kW Wide 25° Beam This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B765C-LM Bronze CHIRP Transducer - Needs Mix & Match Cable - Does NOT Work with Simrad & Lowrance Rely on Airmar’s broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 85 kHz of total bandwidth in just one installation, saving customers time and money. A Thru-Hull Chirp transducer perfectly suited for smaller fishing boats, the B765L/M Chirps across the following bandwidths:*L/M -Low Frequency 40-75 kHz, Medium Frequency 80-130 kHz * Please Note: The low frequency operating band is 300 W. The medium frequency operating band is 600 W. Features Depth & fast-response water-temperature sensor Low—CHIRPS from 40 kHz to 75 kHz, 32° to 21° beamwidth Medium—CHIRPS from 80 kHz to 130 kHz, 24° to 16° beamwidth 85 kHz of total bandwidth from one transducer Covers popular fishing frequencies of 50, 88, and 107 kHz plus everything else in the bandwidth All the advantages of the larger Thru-Hull Chirp transducers, suitable for smaller boats Bronze transducer housing with High-Performance Fairing Boat Size: Up to 9 m (30’) and above Hull Type: Fiberglass or wood Exclusive Xducer ID® technology Hull Deadrise: Up to 24° with a fairing Acoustic Window: Urethane Weight: 2.5 kg (5.5 lb) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B175 Bronze Low Frequency 1kW Chirp Transducer 0° Tilt - Requires Mix & Match Cable Airmar’s low profile Chirp-ready transducer models are the perfect addition to smaller boats such as center consoles. The low frequency band is the deep water performer delivering excellent coverage and tracking in deeper depths. The B175L transducer delivers up to 20 kHz of total bandwidth in just one installation and delivers tremendous deep water performance. The B175L transmits across the following bandwidth: Low Frequency 40 to 60 kHz Tilted element transducers have the ceramic element fixed at either a 20°, 12° or 0° angle within the transducer housing. The transducer is installed almost flush to the hull and the tilted element corrects for the hull deadrise by orienting the beam directly down. This assures maximum echo returns to the transducer and more accurate depth readings. Features: Depth and fast-response water-temperature sensor 1 kW Low Frequency: 40 kHz to 60 kHz with maximum depth performance to 762 m (2500') 32° to 21° beamwidth Great deep water performance High performance, low-profile thru-hull housing provides good resolution at speed when installed properly Bronze housing for use on stepped, planing or displacement hulls in fiberglass or wood Recommended boat size: Up to 11 m (36') Exclusive Xducer ID® technology Specifications: Weight: 2.7 kg (6 lb) Hull Deadrise: 0-7 degrees Acoustic Window: Urethane Hole Size: 98 mm (3-7/8") Seven internal broadband ceramic assemblies This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.