AA Sensor Cable for AA150 & AA560 6.5M (21.3') The Maxwell AA Sensor Cable is compatible with AA150 & AA560 Rode Counters. Features: The male plugs on both ends of this cable are directly compatible with the female plugs on the console and sensor cables Dimensions:  Length: 21.3' (6.5M)

AA Sensor Cable for AA150 & AA560 15M (49.2') The Maxwell AA Sensor Cable is compatible with AA150 & AA560 Rode Counters. Features: The male plugs on both ends of this cable are directly compatible with the female plugs on the console and sensor cables Dimensions:  Length: 49' (15M)

Extension Cable for RCL-95 Searchlight - 5M ACR's Extension Cable extends the wiring for the Dash Mount Point Pad™ by 16.4' (5 M). Compatible With: ACR Dash Mount Point Pad™ Controller ACR RCL-95 Searchlights *Sold as an Individual  WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Infield Installation Connector - VDO Marine Bus/Wind Sensor Cable for AcquaLink® Gauges Infield Installation Connector VDO Marine Bus/Wind Sensor Cable. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Data Cable for TracVision 4, 6, M5, M7 & HD7 - 100' KVH 100' Data Cable Compatible Devices: TracVision 4 TracVision 6 M5 M7 HD7

Power Cable for TracVision 4, 6, M5, M7 & HD7 - 50'  KVH power cable specifically for TracVision 4, 6, M5, M7 & HD7. Specifications: Length: 50'

Sensor & Magnet Kit for AA150, 560, 710 & 730 - Gray Maxwell's Sensor and Magnet Kit is designed specifically for AA150, 560, 710 and 730. Features: Includes Sensor and Magnet Color: Gray

Power Cable f/Dragonfly 5M - 1.5M 1.5M power cable for Dragonfly 5M For use with Dragonfly 5M only.

Fuel Flow Sensor 10-100 LPM/2.6-26.4 GPM When fluid passes through the sensor, the rotors turn. Magnets which are located in the rotors will pass across sensors in the sensor circuit board. Pulses from these sensors are transmitted to the FFM100 which performs flow rate calculations based on the received pulses. Specifications: Construction: Housing Material Aluminum Port Size: 1" NPT Female Maximum Viscosity: 1000 cPs Strainer Size: 60 Mesh (If not already installed after fuel filter) WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Mast Cable f/ Analog Wind Sensor - 30M (98.4") Mast Cable (Analog Wind Sensor) - 30M (98.4') Features: Cable length - 30M (98.4') *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Battery Temperature Sensor (BTS) f/Freedom SW Series The Battery Temperature Sensor (BTS) mounts on a terminal post of a battery in a bank or on the side of a battery and measures its temperature. It sends precise information to the charger or charge controller, which automatically adjusts voltage to help ensure full battery charge depending on the ambient temperature of your battery installation. Features: Gives charger proper temperature compensated charging 25 ft. (7.6m) communications cable Compatible Devices: Freedom SW 2000, 3000, 2000 24V, 3000 24V WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

30M Radar Sensor Cable Assembly Furuno's 30 Meter Radar Sensor Cable Assembly is specifically for Furuno's NavNet 3D. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

20M Radar Sensor Cable Assembly for DRS 2, 4 & 6 Furuno's cable assembly consists of two cables joined together as a Siamese cable. The data cable portion is supplied with RJ45 (Ethernet) connections on each end. The power cable portion is supplied with a 3-pin connector for the display end while the DRS end of the cable has no connector. *Please note that this cable is for the NavNet 3D DRS sensors from 2kW to 12kW. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Power & Data Cable f/ OceanLink Master TFT - Engine # 1 Replacement Power and Data Input Signal Harness used for Engine 1 connector on OceanLink 7” Display Features: Power & Data Cable for Master TFT Displays  Cable length - .5M (1.6') *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

32-Pin Power Cable Single Engine Set-Up - .5M 32-pin power cable for single engine. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.