Male Run T-Fitting - 3/8" x 3/8" Tube x 1/4" NPT Typical Application: Used to connect any 1/4 NPT Female port to our hoses Specifications: 1/4 NPT to 3/8 COMP FITTING Helm side = 1/4 NPT Hose side= 9/16 - 24 UNEF 2A

Shortside Door Hinge Size:1-3/8" x 2-1/4" Fastener: #10(5) Material: Black Nylon

Shortside Door Hinge Size:1-3/8" x 2-1/4" Fastener: #10(5) Material: White Nylon

Mercury Female Hose Tank Fitting - 3/8" Barb Connect your tank and fuel lines with confidence; the durable Acetal construction holds up to lead, unleaded, and alcohol-based fuels. Specifically designed for Mercury/Mariner Brand engines and tanks. Features: Easy installation with barbed fittings for 3/8 inch I.D. (interior diameter) hose (purchase hose clamps separately) Mercury/Mariner Tank Fitting Extremely Versatile: Designed for leaded, unleaded, and alcohol-blended fuel (inch) 3/8" Barb Hose Female *Specifically mates to Attwood part number: 8873-6

Mercury/Yamaha Female Hose Engine Fitting - 3/8" Barb Connect your tank and fuel lines with confidence; the solid machined-brass construction holds up to leaded, unleaded, and alcohol-based fuels for. Features: Solid machined brass for dependable performance, peace of mind Hose female  Tank or Engine End Replaces Yamaha 6Y1-24305-03 *Specifically mates to Attwood part number: 8897-6

PSS Shaft Seal Maintenance & Parts Replacement Kit FOR 1 3/8" SHAFT 2 1/4" TUBE As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow should be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

PSS Shaft Seal 1-3/8" Shaft 2-1/4" Tube Shaft Diameter: 1-3/8" Stern Tube Diameter (D): 2-1/4" to 2-3/8" Total Length (A): 7.38" Total Length (compressed) (Compressed A): 6.38" Rotor Diameter (B): 2.875" Carbon Cuff Diameter (C): 2.5" Stern Cuff Length (E): 1.5" The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm). The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation. **As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced." Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

Adhesive Lined Heat Shrink Tubing (ALT) - 3/8" x 48" - 1-Pack - Black Package of 1 Black 48"(122cm) long sections with a 3/8"(9.5mm) diameter that shrinks to 1/8"(3.2mm) Wire Range: 12-8 AWG Features: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief Highest shrink ratio - shrinks to 1/3 original size Shrinks at 257°F / 125°C Operating temperature range of -40°C to 110°C UL 224 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Adhesive Lined Heat Shrink Tubing (ALT) - 3/8" x 48" - 1-Pack - Red Package of 1 Red 48"(122cm) long sections with a 3/8"(9.5mm) diameter that shrinks to 1/8"(3.2mm) Wire Range: 12-8 AWG Features: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief Highest shrink ratio - shrinks to 1/3 original size Shrinks at 257°F / 125°C Operating temperature range of -40°C to 110°C UL 224 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Description: Plate: 3/4" x 2-1/4" Material: 304 Stainless Steel Stock: 3/8" Eye Ring Diameter: 1" Thread Length: 2-1/2"

Aluminum Fuel Hose Fitting - 3/8" NPT x 3/8" Barb - (Anti-Siphon Valve) This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line. This is a male thread, anti-siphon valve with 3/8-In. NPT x 3/8-In. barb.  Features: Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels Anti-Siphon Valve Material Construction: Aluminum Male thread, hose barb (inch) Male 3/8" NPT x 3/8" Barb  *Use thread sealant on all threads

Universal Aluminum Fuel Hose Fitting - 3/8" NPT x 3/8" Barb This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line. Features: Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels Specifications: Material Construction: Aluminum Male thread, hose barb (inch) Male 3/8" NPT x 3/8" Barb  *Use thread sealant on all threads

Chrysler Female Hose Fitting - 3/8" Barb This Attwood Chrysler Engine Fuel Hose Fitting provides for the precise and effective installation of a fuel line to a Chrysler-brand engine. This Fuel Hose Fitting is a female fitting that connects to the engine end of the fuel line. The fitting has a 3/8-inch barb. Features: Provides precise installation of a fuel line to a Chrysler-brand engine Connects on the engine end of the fuel line Material Construction: Chrome-plated Brass *Specifically mates to Attwood part number: 14509-6

Universal Sprayless Connector - Tank Male (1/4" NPT with Thread Sealant) This Attwood Universal Sprayless Connector reliably eliminates fuel spraying when you are connecting and disconnecting fuel hoses during fueling or maintenance. This connector replaces a traditional fitting and its high-strength body is engineered to withstand the rigors of a marine environment.  Features:  Tank Male fitting all standard 1/4" NPT fittings Has a 1/4-inch NPT with pre-applied thread sealant Pre-applied fuel-grade thread sealant prevents fuel leaks Includes check valves that automatically close upon disconnecting High fuel flow fitting (less than .25kPa restriction at 50 liters/hour) Reliably eliminates fuel spraying when connecting and disconnecting a fuel hose Replaces traditional tank fitting *Compatible with Ethanol blended fuels and with all OEM-brand engines

Johnson/Evinrude/OMC (Outboard Marine Corporation) Male Tank Fitting - 1/4" NPT This Attwood male tank fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels. The threaded fitting has a 1/4" male NPT thread and uses thread sealant on all threads. Clamps are not included. Features: Johnson, Evinrude, and OMC fitting Quick-connect ¼-inch male thread makes installation easy Solid machined brass for dependable performance, peace of mind *Specifically mates to Attwood part numbers: 8889LP6 & 88FHE516-6