|
Executive Adhesive & Fastener Kit w/AT-8040 Adhesive
This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Contains 1 Tube Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastic Or Rubber. AT-8040 Will Hold Even Our Heaviest Parts on a Vertical or Overhead Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225°. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 1 year.
The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc.
The AT-1001003 Kit Contains:
(1) AT-8040 - No Slide Multi Bonder Acrylic Adhesive
<(1) AT-300 - Dispensing Gun
(10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
(100) AT-5 - Large White Cable Tie Mount
(50) AT-3 - Small White Cable Tie Mount
(4) AT-113 - Large Footman's Strap
(10) PS62-832-16SS - 1.00" Long Panel Stud
(4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
(4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base
(4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base
(4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base
(1) Plano Storage Box 14" x 9" x 2.75"
Step By Step Instructions
|
238.40 |
|
|
Adhesively Bonded Fastener Kit with AT 8040 Adhesive
Kit Contains:
(1) Plano Storage Box - 11" x 7.25" x 2.75"
(50) AT-5 Tie Mount (White)
(1) AT-8040 Adhesive
(5) AT-850 Mixing Tip
(1) AT-300 Dispensing Gun
(2) AT-113B Black Footmans Loop
(4) ST125-1420-16 Stainless Stud
|
158.53 |
|
|
Industrial Kit with AT-8040 Adhesive
This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For Industrial Maintenance Shops. A Wide Selection Of Weld Mount Parts Are Supplied In A Heavy "Durham" Metal Box Which Is A Standard Rack Mounted System. The Kit Contains 1 Tubes Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastics And Rubber. AT-8040 Will Hold Even Our Heaviest Parts On An Overhead Or Vertical Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225 Degrees. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 1 year.
The Weld Mount System Eliminates The Need To Drill And Tap, or Weld When Used On Metal Surfaces. Great for Mounting Wire and Conduit Runs, Electrical Boxes And Other Structural Applications.
The AT-7001 Kit Contains:
(1) AT-8040 - No Slide Multi Bonder Adhesive With 12 Minute Kick
(10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
(1) AT-300 - Adhesive Dispensing Gun
(30) AT-3B - Small Black Cable Tie Mount
(100) AT-5B - Large Black Cable Tie Mount
<(25) AT-5 - Large White Cable Tie Mount
(25) AT-7 - Aluminum Base Swivel Wire Tie Mount
(25) AT-9 - Aluminum Wire Tie Mount
(2) AT-113 - Large Footman's Strap White
(2) AT-113B - Large Footman's Strap Black
(6) ST125-1420-12SS - 0.75" Long Stud With 1/4 x 20 Threads 1.25" Base
(6) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
(6) ST125-1024-12SS - 0.75" Long Stud With #10 x 24 Threads 1.25" Base
(6) ST125-1024-20SS - 1.25" Long Stud With #10 x 24 Threads 1.25" Base
(2) SHC-1000 - Single Hose Clamp 1.00"
(2) DHC-1000 - Double Hose Clamp 1.00"
(1) Storage Box - Durham Manufacturing 18.5' x 12.5" x 3.25"
Step By Step Instructions
|
350.40 |
|
|
{Standard Start-Up Kit - No Adhesive
The 65109 Start Up Kit has a wide variety of Weld Mount parts designed to give the user the chance to try numerous applications at a low cost.
Kit Contains:
1 pc AT-300 Adhesive Dispensing Gun
5 pc. AT-850 Adhesive Mixing Tips
50 pc. AT-5 White Tie Mount
2 pc. AT-113 Blarge Black Footman's Strap
4 pc. ST125-1420-12SS 1.00" Stainless Stud
1 Plano Storage Box 11" x 7.25" x 2.75"
|
103.49 |
|
|
Adhesive Mixing Tip For AT-6030
Our AT-650 mixing tip is designed specifically for use with our AT-6030 adhesive. AT-6030 is a 10 to 1 adhesive which requires a mixing tip with more mixing chambers to insure proper mixing before use. These mixing tips minimize waste compared with traditional 6" mixing tips. pkg contains 10 mixing tips.
|
14.78 |
|
|
Executive Fastener Kit - No Adhesive
This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Does NOT Contain Acrylic Adhesive
The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc.
The AT-1001008 Kit Contains:
(1) AT-300 - Dispensing Gun
(10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
(100) AT-5 - Large White Cable Tie Mount
(50) AT-3 - Small White Cable Tie Mount
(4) AT-113 - Large Footman's Strap
(10) PS62-832-16SS - 1.00" Long Panel Stud
(4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
(4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base
(4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base
(4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base
(1) Plano Storage Box 14" x 9" x 2.75"
Step By Step Instructions
|
202.60 |
|
|
Polybonder Kit with AT-880 Adhesive
Kit Contains:
AT-880 Polybonder Adhesive (1)
Dispensing Gun (1)
Mixing Tips (qty 10)
AT-5W (qty 30)
Plano Case
|
150.35 |
|
|
No Slide Metal/Composite Bonder
Revolutionary Metal Bonder will hold heavy parts at application without sliding either on a vertical or overhead surface. AT-8040 will hold 3,500lbs in 40 minutes. No Welding, Drilling or Tapping.
Weld Mount AT-8040 is a solvent free, VOC Compliant, two part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments. It will also bond engineered thermo- and thermosetting plastics, composites to metals or various substrate combinations. It has excellent adhesion to as received metal surfaces including aluminum, stainless steel, galvanized steel, and plated steels. AT-8040 forms a tough, high strength bonds usually with minimal surface preparation developing handling strength in 12 minutes and a functional cure within 45 minutes. Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. AT-8040 will hold all Weld Mount parts on a vertical or overhead surface without sagging when properly used.
Features:
Revolutionary Adhesive
Parts Stay Where Placed Without Sliding
For Use Overhead and on Vertical Surfaces
No Need for Fixtures
|
33.01 |
|
|
No Slide Metal/Composite Bonder - Case of 10
Revolutionary Metal Bonder will hold heavy parts at application without sliding either on a vertical or overhead surface. AT-8040 will hold 3,500lbs in 40 minutes. No Welding, Drilling or Tapping.
Weld Mount AT-8040 is a solvent free, VOC Compliant, two part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments. It will also bond engineered thermo- and thermosetting plastics, composites to metals or various substrate combinations. It has excellent adhesion to as received metal surfaces including aluminum, stainless steel, galvanized steel, and plated steels. AT-8040 forms a tough, high strength bonds usually with minimal surface preparation developing handling strength in 12 minutes and a functional cure within 45 minutes. Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. AT-8040 will hold all Weld Mount parts on a vertical or overhead surface without sagging when properly used.
Features:
Revolutionary Adhesive
Parts Stay Where Placed Without Sliding
For Use Overhead and on Vertical Surfaces
No Need for Fixtures
Case of 10
|
298.64 |
|
|
AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10
Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.
Features:
Square Mixing Tip
4" Long
Case of 10
|
14.98 |
|
|
Industrial Kit - No Adhesive
This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For Industrial Maintenance Shops. A Wide Selection Of Weld Mount Parts Are Supplied In A Heavy "Durham" Metal Box Which Is A Standard Rack Mounted System.
The Weld Mount System Eliminates The Need To Drill And Tap, or Weld When Used On Metal Surfaces. Great for Mounting Wire and Conduit Runs, Electrical Boxes And Other Structural Applications.
The AT-7008 Kit Contains:
(10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
(1) AT-300 - Adhesive Dispensing Gun
(30) AT-3B - Small Black Cable Tie Mount
(100) AT-5B - Large Black Cable Tie Mount
(25) AT-5 - Large White Cable Tie Mount
(25) AT-7 - Aluminum Base Swivel Wire Tie Mount
(25) AT-9 - Aluminum Wire Tie Mount
(2) AT-113 - Large Footman's Strap White
(2) AT-113B - Large Footman's Strap Black
(6) ST125-1420-12SS - 0.75" Long Stud With 1/4 x 20 Threads 1.25" Base
(6) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
(6) ST125-1024-12SS - 0.75" Long Stud With #10 x 24 Threads 1.25" Base
(6) ST125-1024-20SS - 1.25" Long Stud With #10 x 24 Threads 1.25" Base
(2) SHC-1000 - Single Hose Clamp 1.00"
(2) DHC-1000 - Double Hose Clamp 1.00"
(1) Storage Box - Durham Manufacturing 18.5' x 12.5" x 3.25"
Step By Step Instructions
|
318.40 |
|
|
AT-850 Square Mixing Tip 4" - Case of 50
Weld Mount's AT-850 tip is for use only with the 2010, 4010, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.
Features:
Square Mixing Tip
4" Long
Case of 50
|
69.79 |
|
|
Weld Mount
The Weld Mount System is a unique line of fasteners designed to be adhesively bonded to almost any surface, elimintating the need for drilling, tapping or welding. Weld Mount offers wire tie mounts, hose and cable clamps, studs, standoffs and floating nutplates. All of Weld Mount fasteners are mounted with the unique non-sag acrylic adhesives which hold the parts in place on a vertical or overhead surface providing a permanent high strength bond.
|
|
|
AT-14 1 to 1 Adhesive Gun Plunger f/AT-2010, AT-4020 & AT-6030 Adhesives
AT-14 is specifically for Weld Mount AT-2010, AT-4020 and AT-6030 adhesives.
|
11.96 |
|
|
AT-651 Mixing Tips for Use with AT-6031 Adhesive - Qty. 10
Weld Mount’s AT-651 mixing tip is designed specifically for use with Weld Mount’s AT-6031 adhesive. AT-6031 is a 10 to 1 adhesive that requires a mixing tip with more mixing chambers to ensure proper mixing before use. These mixing tips minimize waste compared with traditional 6" mixing tips.
This package contains 10 mixing tips.
Features:
10 to 1 adhesive
|
13.94 |
|