|
14" x 12" Standard Performance Trim Tab Kit w/o Switch Kit- 12V
Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15054-001 actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (#116) upper mounting bracket with gland seal
2 each of #50014-001 (#119) lower mounting bracket
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 19' to 34'
Length of Tab: 14"
Width of Tab: 12"
Minimum Transom Height: 11"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
753.78 |
|
|
14" x 12" High Performance Trim Tab Kit w/o Switch Kit-12V - Single Actuator
Lenco HP Single & Dual Actuator Electric Trim Tab Kits feature electro-polished 7 Gauge 304SS Blades & Sacrificial Anodes. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections.
Each kit is factory assembled with extreme duty actuators with 3/8" SS bolts, a full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes.
Kit Contents:
2 each of stainless steel trim tab planes
2 each of #15056-001 XD extreme duty actuators with 6' lead & Deutsch plugs
Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes.
The following to be supplied by customer:
Boat mounting hardware supplied by customer
Actuator extension harnesses (2 for single actuator application or 4 for dual) will be
required. To order the lengths of your choice see the Lenco Accessories Section.
Specifications:
Suggested Boat Length: 16' to 32'
Length of Tab: 14"
Width of Tab: 12"
Minimum Transom Height: 10.5"
Blades: 7 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Switch Required: 10222-211D, 15069-001
or 15070-001
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1511.23 |
|
|
9" x 12" Standard Performance Trim Tab Kit w/o Switch Kit- 12V
Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15054-001 actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (#116) upper mounting bracket with gland seal
2 each of #50014-001 (#119) lower mounting bracket
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 16' to 26'
Length of Tab: 9"
Width of Tab: 12"
Minimum Transom Height: 13.5"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
690.76 |
|
|
16" x 12" Standard Performance Trim Tab Kit w/o Switch Kit- 12V
Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15054-001 actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (#116) upper mounting bracket with gland seal
2 each of #50014-001 (#119) lower mounting bracket
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 19' to 34'
Length of Tab: 16"
Width of Tab: 12"
Minimum Transom Height: 11"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
814.27 |
|
|
12" x 9" Standard Performance Trim Tab Kit w/o Switch Kit- 12V
Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15054-001 actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (#116) upper mounting bracket with gland seal
2 each of #50014-001 (#119) lower mounting bracket
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 16' to 26'
Length of Tab: 12"
Width of Tab: 9"
Minimum Transom Height: 11"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
682.24 |
|
|
21" x 14" High Performance Trim Tab Kit w/o Switch Kit-12V - Dual Actuator
Lenco HP Single & Dual Actuator Electric Trim Tab Kits feature electro-polished 7 Gauge 304SS Blades & Sacrificial Anodes. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections.
Each kit is factory assembled with extreme duty actuators with 3/8" SS bolts, a full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes.
Kit Contents:
2 each of stainless steel trim tab planes
4 each of #15056-001 XD extreme duty actuators with 6' lead & Deutsch plugs
Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes.
The following to be supplied by customer:
Boat mounting hardware supplied by customer
Actuator extension harnesses (2 for single actuator application or 4 for dual) will be
required. To order the lengths of your choice see the Lenco Accessories Section.
Specifications:
Suggested Boat Length: 24' to 42'
Length of Tab: 21"
Width of Tab: 14"
Minimum Transom Height: 10.5"
Blades: 7 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Switch Required: 15071-001
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2216.93 |
|
|
25" x 14" High Performance Trim Tab Kit w/o Switch Kit-12V - Dual Actuator
Lenco HP Single & Dual Actuator Electric Trim Tab Kits feature electro-polished 7 Gauge 304SS Blades & Sacrificial Anodes. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections.
Each kit is factory assembled with extreme duty actuators with 3/8" SS bolts, a full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes.
Kit Contents:
2 each of stainless steel trim tab planes
4 each of #15056-001 XD extreme duty actuators with 6' lead & Deutsch plugs
Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes.
The following to be supplied by customer:
Boat mounting hardware supplied by customer
Actuator extension harnesses (2 for single actuator application or 4 for dual) will be
required. To order the lengths of your choice see the Lenco Accessories Section.
Specifications:
Suggested Boat Length: 28' to 46'
Length of Tab: 25"
Width of Tab: 14"
Minimum Transom Height: 10.5"
Blades: 7 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Switch Required: 15071-001
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2541.64 |
|
|
14" x 12" Heavy Duty Performance Trim Tab Kit w/o Switch Kit -12V
Lenco Electric Heavy Duty Polished Blade Trim Tab Kits are supplied with electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges, 85 degree inside taper and 1/4" diameter hinge pin. Kits equipped with Extreme Duty actuators with 5/16" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. .
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15055-001 XD extreme duty actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
1 each of the Lenco owner’s / installation manual
Boat-mounting hardware supplied by customer
Specifications:
Suggested Boat Length: 19' to 36'
Length of Tab: 14"
Width of Tab: 12"
Minimum Transom Height: 10.5"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Switch Required: 15069-001 or 15070-001
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1160.16 |
|
|
18" x 14" Standard Performance Trim Tab Kit w/o Switch Kit- 12V
Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15054-001 actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (#116) upper mounting bracket with gland seal
2 each of #50014-001 (#119) lower mounting bracket
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 22' to 40'
Length of Tab: 18"
Width of Tab: 14"
Minimum Transom Height: 11"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
931.00 |
|
|
24" x 14" Extreme Duty Performance Trim Tab Kit w/o Switch Kit- 12V- Dual Actuator Kit
Lenco Electric Extreme Duty Polished Blade Trim Tab Kits feature fast response actuators for precise control. They are fully submersible and feature Plug & Play Deutsch connections. Blades are Electro-Polished 10 Gauge - 304 SS with 1" turned up edges, an 85 degree inside taper and 3/8"diameter hinge pin. Extreme Duty actuators with 3/8" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes.
Kit Contents:
2 each of stainless steel trim tab planes
4 each of #15056-001XD extreme duty actuators with 6" lead & Deutsch plugs
Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes.
The following to be supplied by customer:
Boat mounting hardware
Actuator extension harnesses (2 for single actuator application or 4 for dual)
will be required. Order the lengths of your choice. See the Lenco
Accessories section.
Specifications:
Suggested Boat Length: 25' to 50'
Length of Tab: 24"
Width of Tab: 14"
Minimum Transom Height: 10.5"
Blades: 10 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Switch Required: 15071-001
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2455.00 |
|
|
9" x 9" Standard Performance Trim Tab Kit w/o Switch Kit- 12V
Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15054-001 actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (#116) upper mounting bracket with gland seal
2 each of #50014-001 (#119) lower mounting bracket
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 13' to 20'
Length of Tab: 9"
Width of Tab: 9"
Minimum Transom Height: 13.5"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
649.85 |
|
|
12" x 12" Standard Performance Trim Tab Kit w/o Switch Kit- 12V
Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15054-001 actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (#116) upper mounting bracket with gland seal
2 each of #50014-001 (#119) lower mounting bracket
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 18' to 32'
Length of Tab: 12"
Width of Tab: 12"
Minimum Transom Height: 11"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
718.86 |
|
|
18" x 12" High Performance Trim Tab Kit w/o Switch Kit-12V - Single Actuator
Lenco HP Single & Dual Actuator Electric Trim Tab Kits feature electro-polished 7 Gauge 304SS Blades & Sacrificial Anodes. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections.
Each kit is factory assembled with extreme duty actuators with 3/8" SS bolts, a full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes.
Kit Contents:
2 each of stainless steel trim tab planes
2 each of #15056-001 XD extreme duty actuators with 6' lead & Deutsch plugs
Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes.
The following to be supplied by customer:
Boat mounting hardware supplied by customer
Actuator extension harnesses (2 for single actuator application or 4 for dual) will be
required. To order the lengths of your choice see the Lenco Accessories Section.
Specifications:
Suggested Boat Length: 20' to 40'
Length of Tab: 18"
Width of Tab: 12"
Minimum Transom Height: 10.5"
Blades: 7 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Switch Required: 10222-211D, 15069-001
or 15070-001
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1575.28 |
|
|
4" x 12" Limited Space Trim Tab Kit w/o Switch Kit -12V - Standard Finish - Short Actuator
Lenco Electric Limited Space Trim Tab Kits are ideal for boats with a swim platform and/or ladder. They can be fitted to transoms that have a limited mounting area. Blades are 12 gauge - 304 SS with front of blade folded to provide a smooth trailing edge and 1/8" diameter hinge pin. Fast response electric actuators for precise control. All units have Plug and Play connections and are fully submersible.
Kit Contents:
2 each of 12-gauge 304 stainless steel trim tab blades
2 each of #15057-001 XD actuator with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (116) upper mounting bracket with gland seal
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 14' to 25'
Length of Tab: 4"
Width of Tab: 12"
Minimum Transom Height: 13"
Blades: 12 Gauge Stainless Steel
Finish: Standard
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
580.00 |
|
|
16" x 12" Heavy Duty Performance Trim Tab Kit w/o Switch Kit -12V
Lenco Electric Heavy Duty Polished Blade Trim Tab Kits are supplied with electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges, 85 degree inside taper and 1/4" diameter hinge pin. Kits equipped with Extreme Duty actuators with 5/16" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. .
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15055-001 XD extreme duty actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
1 each of the Lenco owner’s / installation manual
Boat-mounting hardware supplied by customer
Specifications:
Suggested Boat Length: 20' to 38'
Length of Tab: 16"
Width of Tab: 12"
Minimum Transom Height: 10.5"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Switch Required: 15069-001 or 15070-001
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1198.50 |
|