SP5S1 - Uncut Rail Pod Max Useable Face: (14.75" x 5") Max Cut Out Area: (13.875" x 4.125") Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models). Stainless Steel Clamp A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails. Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

SP3S1 - Uncut Rail Pod Max Useable Face: (13.75" x 9") Max Cut Out Area: (12.938" x 8.125") Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models). Stainless Steel Clamp A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails. Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

SP2S1 - Uncut Rail Pod Max Useable Face: (11.75" x 7") Max Cut Out Area: (11" x 6.125") Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models). Stainless Steel Clamp A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails. Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

Seaview SPOD Sail Pod Box Max Usable Face: 14.75" x 5" Max Cut Out Area: 13.875" x 4.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems. Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation.  Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview DPOD Deck Power Pod Box Max Usable Face: 14.75" x 5" Max Cut Out Area: 13.875" x 4.125"  The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply pull the secure bolt out and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply push the secure bolt back in, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Add-On Instrument Pod - Uncut Max Usable Face: 4.625" x 4.625" Max Cut Out Area: 4.125" x 4.125" This Seaview Accessory Pod can be mounted to Seaview Sail Pods, Deck Pods or Rail Pods. These Accessory Pods give you the flexibility to mount additional instruments. Made from high quality marine grade UV resistant ABS plastic and is held together with tamper resistant security screws. A water tight gasket prevents water from intruding into the pod. Depending on the size of your Sail Pod, Deck Pod or Rail Pod one to four Accessory Pods can be mounted.

Seaview SPOD Sail Pod Box Max Usable Face: 4.625" x 4.625" Max Cut Out Area: 4.125" x 4.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems.  Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

BURKS 9680-4.13, BRONZE IMPELLER 4.13" UNSPSC Code: 40150000

Seaview SPOD Sail Pod Box Max Usable Face: 11.75" x 7" Max Cut Out Area: 11" x 6.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems.  Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

Seaview DPOD Deck Power Pod Box Max Usable Face: 13.75" x 9" Max Cut Out Area: 12.938" x 8.125" The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply pull the secure bolt out and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply push the secure bolt back in, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview DPOD Deck Power Pod Box Max Usable Face: 11.75" x 7" Max Cut Out Area: 11" x 6.125" The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply loosen the locking screw and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply tighten the locking screw, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Scanpod Helm Pod Uncut for 9" Displays With great design features, the Scanstrut Helm Pod is a perfect choice for all cockpit configurations. With options to fit radar displays, chartplotters and standard navigation instruments, the choice is yours! For Displays & Standard Instruments: Fits up to 9" displays Can accommodate 3 or 4 standard instruments (e.g. ST60) Usable face 13.2H x 8.14W Features: UNIVERSAL HELM FIXING Fits pedestal rails from 25mm to 33.7mm (0.98″ – 1.33″) diameter. Using a unique clamping system, the Deep Pod's can fit rail widths from 178mm (7”) upwards.* SECURE & WATERTIGHT INSTALL Saddle system supports the stainless tubing enabling a secure and rigid fit onto any pedestal and also ensures a watertight seal at cable entry. NO DRILL FIXING KIT Customised U-bolts fit around rail and through the saddles into the back of the pod eliminating the need for time consuming and awkward drilling of the stainless rail. HASSLE FREE INSTALL & SERVICE Fixings fit from back to front cutting their threads into injection moulded ABS inserts designed into the Pod front. This design allows for a quick and safe install and repeat servicing. INCREASED PROTECTION Pod seal is manufactured from a high tear strength silicone, it has a very high resistance to heat and UV so you can have confidence that it won’t deteriorate over time. SUPPLIED UNCUT As standard you will receive your Scanpod uncut. For larger orders, a factory cutting service is available.

Scanpod 7" Helm Pod Rail Mount Features: Applications: Designed for (1) 7" Instrument Current sailboat designs often have very open cockpits with few options for installing retro-fit instruments The Rail Pod gives you an option for fitting smaller displays and instruments directly onto a rail, in a position which suits you Rail Mounted Universal Fixing Fits pedestal rails from 25mm to 33.7mm (0.98" - 1.33") Fit your display onto standard and curved rails Great Viewing Options Viewing angle can be set upon installation Cables are routed internally through the clamp and onto the rail Increased Protection Pod seal is manufactured from a high tear strength silicone, it has a very high resistance to heat and UV so you can have confidence that it won't deteriorate over time Supplied Uncut - As standard you will receive your Scanpod uncut

ScanPod Uncut Fits .98" to 1.33" Rail with Switches, Small Screens & Remote Controls The cleanest way to mount your small electronics on a rail. The Rail Pod allows you to install your small screens, switches, controllers, chain counters, and more onto any standard or curved rail. Waterproof internal cable routing allows you to seamlessly run your cables through the bottom of the pod, the machined aluminum clamp, and into the rail. Waterproof internal cable routing allows you to seamlessly run your cables through the bottom of the pod, this gives you the cleanest and most user-friendly way to mount your small electronics right where you need it the most. Some additional work may be required to the cables and connectors of the device to ensure a suitable fit. Pod seal is manufactured from a high tear strength silicone; it has a very high resistance to heat and UV so you can have confidence that it won’t deteriorate over time. Features: As standard, you will receive your SPR-1u-RM uncut    Fits rails from 25mm to 33.7mm (0.98” to 1.33”). Fit your electronics onto standard and curved rails The viewing angle can be set upon installation. Cables are routed internally through the clamp and onto the rail

Scanpod Helm Pod Uncut for 10" to 12" Displays With great design features, the Scanstrut Helm Pod is a perfect choice for all cockpit configurations. With options to fit radar displays, chartplotters and standard navigation instruments, the choice is yours! For Displays & Standard Instruments: Fits 10" to 12" displays Can accommodate 3 or 4 standard instruments (e.g. ST60) Usable face 14.7H x 9.7W   Features: UNIVERSAL HELM FIXING Fits pedestal rails from 25mm to 33.7mm (0.98″ – 1.33″) diameter. Using a unique clamping system, the Deep Pod's can fit rail widths from 178mm (7”) upwards.* SECURE & WATERTIGHT INSTALL Saddle system supports the stainless tubing enabling a secure and rigid fit onto any pedestal and also ensures a watertight seal at cable entry. NO DRILL FIXING KIT Customised U-bolts fit around rail and through the saddles into the back of the pod eliminating the need for time consuming and awkward drilling of the stainless rail. HASSLE FREE INSTALL & SERVICE Fixings fit from back to front cutting their threads into injection moulded ABS inserts designed into the Pod front. This design allows for a quick and safe install and repeat servicing. INCREASED PROTECTION Pod seal is manufactured from a high tear strength silicone, it has a very high resistance to heat and UV so you can have confidence that it won’t deteriorate over time. SUPPLIED UNCUT As standard you will receive your Scanpod uncut. For larger orders, a factory cutting service is available.