SP2S1 - Uncut Rail Pod Max Useable Face: (11.75" x 7") Max Cut Out Area: (11" x 6.125") Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models). Stainless Steel Clamp A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails. Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

SP3S1 - Uncut Rail Pod Max Useable Face: (13.75" x 9") Max Cut Out Area: (12.938" x 8.125") Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models). Stainless Steel Clamp A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails. Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

SP5S1 - Uncut Rail Pod Max Useable Face: (14.75" x 5") Max Cut Out Area: (13.875" x 4.125") Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models). Stainless Steel Clamp A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails. Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

Seaview SPOD Sail Pod Box Max Usable Face: 11.75" x 7" Max Cut Out Area: 11" x 6.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems.  Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

Hollow Back 304 Stainless Steel Rub Rail Insert 3/4" x 6' Sold in 6' increments.  Features: Sold in 6' Stainless Steel Type-304/316L Drilled and countersunk for #8 screws on 6-inch centers 5-year limited warranty

Deluxe Trailer Tie-Down - 2" x 6' - Pair This deluxe 2" x 6' trailer tie-down is our finest over-center locking buckle with wrap around buckle protection that is proven to stay clamped under the worst road conditions. It features American made heavy vinyl coated top hook and zinc plated bottom hook. 1,700 lb. capacity - sold in pairs.

Quick Release Trailer Tie-Down - 2" x 6' - Pair This small 2" x 6' over-center, quick release buckle is strong and durable. Features an over center locking buckle, polypropylene belt and protective pad with hook & loop closure for boat protection.

Paddle Buckle Trailer Tie-Down - 2" x 6' - Pair This 2" x 6' popular tie-down system is made with a 2” paddle buckle, polypropylene belt and protective pad with hook and loop closure for boat protection. It features American made heavy vinyl coated top hook and zinc plated bottom hook. 1,000 lb. capacity - sold in pairs.

Seaview DPOD Deck Power Pod Box Max Usable Face: 11.75" x 7" Max Cut Out Area: 11" x 6.125" The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply loosen the locking screw and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply tighten the locking screw, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Part #: GP2050 Description: Uncut NavPod Protects Your Electronics In Harsh Conditions Uncut Flush Front Usable Face = 12.75"w x 8.75"h Grand Prix series outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability. Polished stainless steel tamperproof fasteners. NavPod allows you to place your electronics within reach. Dimensions (15.125"w x 10.88"h x 6.125"d) Centimeters (38.42w x 27.62h x 15.56d).

PART #: GP1040 Description: Uncut (usable face = 17.5"w x 7.375"h) W x H x D: 20.25" x 9.5" x 6.125" NavPod Protects Your Electronics In Harsh Conditions Un-Cut NavPods are for you to choose your own layout or for mounting electronics that NavPod doesn't provide a Pre-Cut for. The face of the NavPod can easily be cut with a "Rotozip". It's a small handheld router style cutter that shreds the material while cutting. This eliminates any melting of the plastic material. It is also important to note that when selecting a possible Un-cut NavPod, the depth measurement stated in the chart is overall outside measurement. Actual internal clearance can be reduced by curvature from the design or molded indents for the mounting system. This can reduce the overall and needs to be considered when making a determination of actual available depth clearance. Watertight Silicone Seal Keeps rain and salt water spray off electrical connections on the back of electronics Tamperproof Special fasteners and wrench are included that provide security and convenience to leave electronics on-board Concealed Wiring No loose wires are exposed to corrosion and UV damage Clean Installation The clean look of flush mounting. Mount your display where you can best see and reach it. Pre-Cut Models Come with a Flush Mount Kit, which includes the specific gasket and mounting hardware for your electronics if not supplied by manufacturer with unit.

GP1050 Uncut Flush Front Uncut - Flush Front (usable face = 12.75"w x 8.75"h). Grand Prix series outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability. Polished stainless steel tamperproof fasteners. NavPod allows you to place your electronics within reach. Dimensions (15.125"w x 10.88"h x 6.125"d)

G-6 Twin Eye Fender 11" x 30" - Sand with Adapter Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes, and reinforced ropeholds for long-term durability.  Utility boat fenders with Polyform dependability. Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced ropeholds Designed for use by trailered boats and in permanent protected moorings Twin-eye design for vertical or horizontal use Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 11" x 30" (27.9 x 76.2cm) Eye Diameter - .875" (2.2cm) Circumference - 34.6" (87.8cm) Volume - 8.5 gallons (32.2L) Boat Size - 35' - 40' (10.7 - 12.2M) Weight - 6.7lbs In the Box: Fender Inflation Adapter  *Sold as a Kit

Groco S-73-X Tie Rod Outside 316 SS .250 X 6.75  

Add-On Instrument Pod - Uncut Max Usable Face: 4.625" x 4.625" Max Cut Out Area: 4.125" x 4.125" This Seaview Accessory Pod can be mounted to Seaview Sail Pods, Deck Pods or Rail Pods. These Accessory Pods give you the flexibility to mount additional instruments. Made from high quality marine grade UV resistant ABS plastic and is held together with tamper resistant security screws. A water tight gasket prevents water from intruding into the pod. Depending on the size of your Sail Pod, Deck Pod or Rail Pod one to four Accessory Pods can be mounted.