11" Wide x 12' Long Grey Carpet Roll 11" wide covers a 2x4 or a 2x6 board Marine grade carpet Weather resistant 100% PET polyester High quality Durable backing Minimal water retention 16.oz per square yard weight Pile height 5/32"

11" Wide x 12' Long Black Carpet Roll 11" wide covers a 2x4 or a 2x6 board Marine grade carpet Weather resistant 100% PET polyester High quality Durable backing Minimal water retention 16.oz per square yard weight Pile height 5/32"

11" Wide x 12' Long Blue Carpet Roll 11" wide covers a 2x4 or a 2x6 board Marine grade carpet Weather resistant 100% PET polyester High quality Durable backing Minimal water retention 16.oz per square yard weight Pile height 5/32"

18" Wide x 18' Long Grey Carpet Roll 18" wide covers a 3x8 or a 4x8 board Marine grade carpet Weather resistant 100% PET polyester High quality Durable backing Minimal water retention 16.1oz per square yard weight Pile height 5/32"

18" Wide x 18' Long Black Carpet Roll 18" wide covers a 3x8 or a 4x8 board Marine grade carpet Weather resistant 100% PET polyester High quality Durable backing Minimal water retention 16.1oz per square yard weight Pile height 5/32"

Package Roller Shaft 1/2" x 12-3/4" with Cap Nuts - Zinc Roller shafts blister packed each with two cap nuts. Features: Length: 12-3/4" Max Grip: 12.190"

Flex Keel Pad - Full Cap Style - 12" x 3" - Gold These Thermal Plastic Rubber (TPR) pads cushion the trailer cross members to protect your boat keel. Full cap style mounts on the center of any 3" wide cross member or axle that the keel might hit. Features: Yellow TPR 3" W x 12" L 5/16" thick 3/4" deep sides for mounting Mount using four rivets or screws, two through each side (hardware not included).

Flex Keel Pad - Full Cap Style - 12" x 3" - Blue These Thermal Plastic Rubber (TPR) pads cushion the trailer cross members to protect your boat keel. Full cap style mounts on the center of any 3" wide cross member or axle that the keel might hit. Features: Blue TPR 3" W x 12" L 5/16" thick 3/4" deep sides for mounting Mount using four rivets or screws, two through each side (hardware not included).

Pontoon Curved Corner-Gard - 3"W x 12"L This unique Corner-Gard offers a level of protection to areas on the Pontoon boat other fenders or bumpers can't provide. The Pontoon Corner-Gard comes shaped to mount on either a radius style or 90o pontoon corners. The Corner-Gard mounts over the original factory installed aluminum corner section to provide air-cushioning impact protection when docking. Special silver PVC formulated to match the aluminum color of the boat and secures with the included stainless fasteners.  Specifications: Dimensions: 3"W x 12"L Mounting hardware included

40" Post Guide-On with L.E.D. Posts & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 40" Post Guide-Ons With L.E.D. Posts and two Camo Wet Lands Post Guide-On Pads. The Post Guide-Ons allows you to see the location of your trailer when it's underwater. Equipped with long-lasting, waterproof, and shockproof, one-piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware and wiring included  40" Total Height Adjusts Out to 13" on each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" sq. 16 ga Pre-Galvanized Steel post Extends 18" Into 2" PVC tube for strength Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27740: C.E. Smith 40" Post Guide-On With LED Lighted Posts   Part 27902: C.E. Smith Post Guide-On Pad - 36" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Post Guide-On with L.E.D. Posts & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 60" Post Guide-Ons With L.E.D. Posts and two Camo Wet Lands Post Guide-On Pads. The Post Guide-Ons allows you to see the location of your trailer when it's underwater. Equipped with long-lasting, waterproof, and shockproof, one-piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features:  Mounting hardware and wiring included  Adjusts Out to 19" on each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" square, 16 gauge pre-galvanized steel uprights that are 39" high 2-3/8" diameter white PVC posts Stands 60" above the trailer frame Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27760: C.E. Smith 60" Post Guide-On With L.E.D. Posts Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Post Guide-On with I-Beam Mounting Kit & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 60" Post Guide-Ons With I-Beam Mounting Kits and two Camo Wet Lands Post Guide-On Pads. These Post Guide-Ons allow you to see the location of your trailer when it's underwater. Designed for I-beam trailers and I-beam boat lifts, these guide-ons feature an innovative two-piece mounting clamp that works above or below the I-beam. Brackets will fit onto any height and virtually any width I-beam trailer frame. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware included Adjusts out to 19" on each side 1-1/2" square. 16 gauge pre-galvanized steel uprights 2-3/8" diameter white PVC posts Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post-guide-on covers: Camo Wet Lands Kit Includes: Part 27648: C.E. Smith 60" Post Guide-On With I-Beam Mounting Kit  Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Post Guide-On with Unlighted Posts & FREE Camo Wet Lands Post Guide-On Pads This kit includes two 60" Post Guide-On With Unlighted Posts and two Camo Wet Lands Post Guide-On Pads. These Post Guide-Ons allow you to see the location of your trailer when it's underwater. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware included Adjusts out to 19" on each side Fits frames up to 3" W x 4-1/4" H 1-1/2" square, 16 gauge pre-galvanized steel uprights 39" high 2-3/8" diameter white PVC posts. Stands 60" above the trailer frame with white post caps. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27640: C.E. Smith 60" Post Guide-On With Unlighted Posts  Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  *Sold in pairs

Package Roller Shaft 1/2" x 5-1/4" with Cap Nuts - Zinc Roller shafts blister packed each with two cap nuts. Features: Length: 5-1/4" Max Grip: 4.690"

Package Roller Shaft 1/2" x 6-1/4" with Cap Nuts - Zinc Roller shafts blister packed each with two cap nuts. Features: Length: 6-1/4" Max Grip: 5.690"