Add-On Instrument Pod - Uncut
Max Usable Face: 4.625" x 4.625"
Max Cut Out Area: 4.125" x 4.125"
This Seaview Accessory Pod can be mounted to Seaview Sail Pods, Deck Pods or Rail Pods. These Accessory Pods give you the flexibility to mount additional instruments.
Made from high quality marine grade UV resistant ABS plastic and is held together with tamper resistant security screws. A water tight gasket prevents water from intruding into the pod.
Depending on the size of your Sail Pod, Deck Pod or Rail Pod one to four Accessory Pods can be mounted.
|
120.00 | |
Scanpod Instrument Pod - Uncut - Arm Mounted - Fits 1" - 1.3" Rails
Current sailboat designs often have very open cockpits with few options for installing retro-fit instruments.
Options available to install a 7" display or standard instrument.
Arm Mounted:
Extend the Rail Pod away from narrow or crowded rails for better viewing
Designed to ensure the Pod is always positioned for best viewing, whatever the angle of the rail
|
386.89 | |
Add-On Uncut Single Instrument Pod for Triton2
Max Usable Face: (5" x 5")
Max Cutout Area: (4.38" x 4.38")
This Seaview Accessory Pod can be mounted to Seaview Sail Pods, Deck Pods or Rail Pods. These Accessory Pods give you the flexibility to mount additional instruments.
Made from high quality marine grade UV resistant ABS plastic and is held together with tamper resistant security screws. A water tight gasket prevents water from intruding into the pod.
Depending on the size of your Sail Pod, Deck Pod or Rail Pod one to four Accessory Pods can be mounted.
|
144.00 | |
Scanpod Single Instrument Pod - Uncut - Arm Mounted - Fits 1" - 1.3" Rails
Current sailboat designs often have very open cockpits with few options for installing retro-fit instruments.
Options available to install a 7" display or standard instrument.
Arm Mounted:
Extend the Rail Pod away from narrow or crowded rails for better viewing
Designed to ensure the Pod is always positioned for best viewing, whatever the angle of the rail
|
206.47 | |
Uncut Single Instrument Pod for Triton2 - Stainless Steel Clamp
Max Useable Face: (5″ × 5″)
Max Cut Out Area: (4.38″ × 4.38″)
Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models).
Stainless Steel Clamps
A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails.
Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in.
Optional Accessory Pod
One of the unique abilities with the Rail Pod is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.
|
206.40 | |
SP2S1 - Uncut Rail Pod
Max Useable Face: (11.75" x 7")
Max Cut Out Area: (11" x 6.125")
Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models).
Stainless Steel Clamp
A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails.
Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in.
Optional Accessory Pod
One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.
|
331.20 | |
SP3S1 - Uncut Rail Pod
Max Useable Face: (13.75" x 9")
Max Cut Out Area: (12.938" x 8.125")
Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models).
Stainless Steel Clamp
A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails.
Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in.
Optional Accessory Pod
One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.
|
374.40 | |
SP5S1 - Uncut Rail Pod
Max Useable Face: (14.75" x 5")
Max Cut Out Area: (13.875" x 4.125")
Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models).
Stainless Steel Clamp
A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails.
Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in.
Optional Accessory Pod
One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.
|
307.20 | |
Seaview SPOD Sail Pod Box
Max Usable Face: 4.625" x 4.625"
Max Cut Out Area: 4.125" x 4.125"
The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems.
Achieve the Perfect View
The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation.
Stainless Steel Clamps
Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails.
Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in.
Optional Accessory Pod
One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.
|
187.20 | |
Seaview SPOD Sail Pod Box
Max Usable Face: 11.75" x 7"
Max Cut Out Area: 11" x 6.125"
The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems.
Achieve the Perfect View
The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation.
Stainless Steel Clamps
Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails.
Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in.
Optional Accessory Pod
One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.
|
340.80 | |
Scanpod Helm Pod Uncut for 10" to 12" Displays
With great design features, the Scanstrut Helm Pod is a perfect choice for all cockpit configurations.
With options to fit radar displays, chartplotters and standard navigation instruments, the choice is yours!
For Displays & Standard Instruments:
Fits 10" to 12" displays
Can accommodate 3 or 4 standard instruments (e.g. ST60)
Usable face 14.7H x 9.7W
Features:
UNIVERSAL HELM FIXING
Fits pedestal rails from 25mm to 33.7mm (0.98″ – 1.33″) diameter. Using a unique clamping system, the Deep Pod's can fit rail widths from 178mm (7”) upwards.*
SECURE & WATERTIGHT INSTALL
Saddle system supports the stainless tubing enabling a secure and rigid fit onto any pedestal and also ensures a watertight seal at cable entry.
NO DRILL FIXING KIT
Customised U-bolts fit around rail and through the saddles into the back of the pod eliminating the need for time consuming and awkward drilling of the stainless rail.
HASSLE FREE INSTALL & SERVICE
Fixings fit from back to front cutting their threads into injection moulded ABS inserts designed into the Pod front. This design allows for a quick and safe install and repeat servicing.
INCREASED PROTECTION
Pod seal is manufactured from a high tear strength silicone, it has a very high resistance to heat and UV so you can have confidence that it won’t deteriorate over time.
SUPPLIED UNCUT
As standard you will receive your Scanpod uncut. For larger orders, a factory cutting service is available.
|
451.57 | |
Scanpod Helm Pod Uncut for 9" Displays
With great design features, the Scanstrut Helm Pod is a perfect choice for all cockpit configurations.
With options to fit radar displays, chartplotters and standard navigation instruments, the choice is yours!
For Displays & Standard Instruments:
Fits up to 9" displays
Can accommodate 3 or 4 standard instruments (e.g. ST60)
Usable face 13.2H x 8.14W
Features:
UNIVERSAL HELM FIXING
Fits pedestal rails from 25mm to 33.7mm (0.98″ – 1.33″) diameter. Using a unique clamping system, the Deep Pod's can fit rail widths from 178mm (7”) upwards.*
SECURE & WATERTIGHT INSTALL
Saddle system supports the stainless tubing enabling a secure and rigid fit onto any pedestal and also ensures a watertight seal at cable entry.
NO DRILL FIXING KIT
Customised U-bolts fit around rail and through the saddles into the back of the pod eliminating the need for time consuming and awkward drilling of the stainless rail.
HASSLE FREE INSTALL & SERVICE
Fixings fit from back to front cutting their threads into injection moulded ABS inserts designed into the Pod front. This design allows for a quick and safe install and repeat servicing.
INCREASED PROTECTION
Pod seal is manufactured from a high tear strength silicone, it has a very high resistance to heat and UV so you can have confidence that it won’t deteriorate over time.
SUPPLIED UNCUT
As standard you will receive your Scanpod uncut. For larger orders, a factory cutting service is available.
|
390.83 | |
Scanpod Deck Pod Uncut for 10" to 12" Displays
Solve the challenge of finding a level mounting surface to install your displays onto your powerboat, RIB or sailboat wheelhouse.
For Displays and Standard Instruments:
Fits 10" to 12" Displays
Usable face 14.7H x 9.7W
Accomodates 3/4 Standard instruments (e.g. ST60)
Features:
SWIVEL & TILT BASE
One handed quick release action. Simply release the lever, swivel and tilt to suit your requirements before locking back into position.
BEST VIEWING ANGLE
An adjustable ball joint allows range of movement and multiple mounting angles.
ADDED STRENGTH
Inner bracing plate secures the Deck Pod base to the pod and gives increased rigidity to the assembly eliminating potential damaged from shock and vibration.
OVERHEAD MOUNTING
Deck Pod models can be overhead mounted. Refer to part number guide for compatibility.
HASSLE FREE INSTALL & SERVICE
Fixings fit from back to front cutting their threads into injection moulded ABS inserts designed into the Pod front. This design allows for a quick and safe install and repeat servicing.
INCREASED PROTECTION
Pod seal is manufactured from a high tear strength silicone, it has a very high resistance to heat and UV so you can have confidence that it won’t deteriorate over time.
SUPPLIED UNCUT
As standard you will receive your Scanpod uncut (for tips on cutting, please view the FAQ tab). For larger orders, a factory cutting service is available.
|
478.57 | |
Scanpod Deck Pod Uncut for 9" Displays
Solve the challenge of finding a level mounting surface to install your displays onto your powerboat, RIB or sailboat wheelhouse.
For Displays and Standard Instruments:
Fits displays up to 9”
Usable face 13.2H x 8.14W
Accomodates 3/4 Standard instruments (e.g. ST60)
Features:
SWIVEL & TILT BASE
One handed quick release action. Simply release the lever, swivel and tilt to suit your requirements before locking back into position.
BEST VIEWING ANGLE
An adjustable ball joint allows range of movement and multiple mounting angles.
ADDED STRENGTH
Inner bracing plate secures the Deck Pod base to the pod and gives increased rigidity to the assembly eliminating potential damaged from shock and vibration.
OVERHEAD MOUNTING
Deck Pod models can be overhead mounted. Refer to part number guide for compatibility.
HASSLE FREE INSTALL & SERVICE
Fixings fit from back to front cutting their threads into injection moulded ABS inserts designed into the Pod front. This design allows for a quick and safe install and repeat servicing.
INCREASED PROTECTION
Pod seal is manufactured from a high tear strength silicone, it has a very high resistance to heat and UV so you can have confidence that it won’t deteriorate over time.
SUPPLIED UNCUT
As standard you will receive your Scanpod uncut (for tips on cutting, please view the FAQ tab). For larger orders, a factory cutting service is available.
|
451.57 | |
Scanstrut ScanPod Uncut Fits .98" to 1.33" Arm Mount Use w/Switches, Small Screens & Remote Controls ScanPod Uncut Fits .98" to 1.33" Arm Mount Use with Switches, Small Screens & Remote Controls
The cleanest way to mount your Instrument on a rail. The Arm Pod allows you to install your instrument onto any standard or curved rail. Waterproof internal cable routing allows you to seamlessly run your cables through the bottom of the pod, the machined aluminum clamp, and into the rail.
Features:
Fits rails from 25mm to 33.7mm (0.98” to 1.33”)
Arm mount enables a secure fit onto any pedestal
Waterproof internal cable routing allows you to seamlessly run your cables through the bottom of the pod, this gives you the cleanest and most user-friendly way to mount your small electronics
Some additional work may be required to the cables and connectors of the device to ensure a suitable fit
Pod seal is manufactured from a high tear strength silicone; it has a very high resistance to heat and UV so you can have confidence that it won’t deteriorate over time
As standard, you will receive your SPR-1u-RM uncut
The viewing angle can be set upon installation. Cables are routed internally through the clamp and onto the rail
|
206.47 | |