Seaview SPOD Sail Pod Box Max Usable Face: 14.75" x 5" Max Cut Out Area: 13.875" x 4.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems. Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation.  Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview SPOD Sail Pod Box Max Usable Face: 16.938" x 12.25" Max Cut Out Area: 16" x 11.25" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems. Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview SPOD Sail Pod Box Max Usable Face: 13.75" x 9" Max Cut Out Area: 12.938" x 8.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems. Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

Seaview SPOD Sail Pod Box Max Usable Face: 4.625" x 4.625" Max Cut Out Area: 4.125" x 4.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems.  Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

Seaview SPOD Sail Pod Box Max Usable Face: 11.75" x 7" Max Cut Out Area: 11" x 6.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems.  Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

GP1302 InstrumentPod Pre-Cut for 3 Instruments (Simrad IS42/B&G Triton/AP44 Square Hole) for 9.5" Wide Guard NavPod InstrumentPod GP1302 for 9.5" Wide Guards are used for mounting three instruments in a single NavPod at the helm or companionway. An InstrumentPod can be mounted on a StraightGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. It can also be used with the SK312 Companionway Mount for positioning sailing instruments above the companionway. Features: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

GP2300 InstrumentPod Uncut f/3 Instruments f/12" Guard NavPod InstrumentPod GP2300 for 12" Guard is used for mounting three instruments in a single NavPod at the helm or companionway. An InstrumentPod can be mounted on a StraightGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. It can also be used with the SK312 Companionway Mount for positioning sailing instruments above the companionway. All InstrumentPods Include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

GP1300 InstrumentPod Uncut fits 3 Instruments for 9.5" Guard NavPod's InstrumentPod GP1300 for 9.5" Guard is used for mounting three instruments in a single NavPod at the helm or companionway. An InstrumentPod can be mounted on a StraightGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. It can also be used with the SK312 Companionway Mount for positioning sailing instruments above the companionway. All InstrumentPods Include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

Seaview DPOD Deck Power Pod Box Max Usable Face: 11.75" x 7" Max Cut Out Area: 11" x 6.125" The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply loosen the locking screw and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply tighten the locking screw, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview DPOD Deck Power Pod Box Max Usable Face: 13.75" x 9" Max Cut Out Area: 12.938" x 8.125" The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply pull the secure bolt out and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply push the secure bolt back in, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview DPOD Deck Power Pod Box Max Usable Face: 14.75" x 5" Max Cut Out Area: 13.875" x 4.125"  The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply pull the secure bolt out and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply push the secure bolt back in, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

PowerPod Pre-Cut for Two Instruments Two 3.6" Holes PowerPods are better than bracket mounting. Sturdy and secure, yet clean and attractive, PowerPods position your fishfinder/chartplotter at a 20-degree viewing angle. PowerPods provide the clean look of flush mounting with the advantages of a swivel base. PowerPods are now available in two color options. All models are available in high gloss white, and many models (PP4400-C, PP4500-C, PP4600-C, PP4800-C, PP4900-C, PP5050-C, PP5100-C, PP5200-C, PP5920-C Series) are also available in black carbon print. Constructed out of durable ABS like all Gen3 NavPods, these new black carbon models have the same high gloss finish with UV stability. NavPods are made to protect your marine electronics from the harshest of wet boating conditions. All NavPods are manufactured with a double gasket system that provides an excellent watertight seal. PowerPods keep the spray off the electrical connections on the back of your fishfinder/chartplotter, assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the PowerPod. The base has a large opening (1.1″ for PP4100, PP4400, PP4500, PP4600 Series; 1.8″ for PP4800, PP4900, PP5030, PP5050, PP5060, PP5100, PP5200, PP5920 models) to provide plenty of room for running wires and connectors through the base to conceal them from the elements. This provides protection for wires and connectors from water intrusion, UV exposure or damage from getting snagged and ripped out of their sockets. All NavPods come with a security wrench and Nickel Chrome-Plated Stainless Steel tamper-resistant screws for a little bling and a lot of security. PowerPod pre-cut models are available for most 7″, 9″, 12″ and 16″ displays from all major marine electronic manufacturers. NavPod backs up their commitment to quality by offering a 10-year warranty on all Gen3 NavPods. PowerPods: Protection, Convenience, Security.

GP1401 InstrumentPod Pre-Cut for 4 Instruments for 9.5" Wide Guard NavPod InstrumentPod GP2400 Series for 12" Guard are used for mounting two - four in a single NavPod at the helm or companionway. An InstrumentPod can be mounted on a StraightGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. It can also be used with the SK312 Companionway Mount for positioning sailing instruments above the companionway. All InstrumentPods include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

GP2401 InstrumentPod Pre-Cut for 4 Instruments for 12" Wide Guard NavPod InstrumentPod GP2400 Series for 12" Guard are used for mounting two - four in a single NavPod at the helm or companionway. An InstrumentPod can be mounted on a StraightGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. It can also be used with the SK312 Companionway Mount for positioning sailing instruments above the companionway. All InstrumentPods include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

GP1402 InstrumentPod Pre-Cut for 4 Instruments (Simrad IS42/B&G Triton/AP44 Square Hole) for 9.5" Wide Guard NavPod InstrumentPod GP1402 for 9.5" Wide Guards are used for mounting four instruments in a single NavPod at the helm or companionway. An InstrumentPod can be mounted on a StraightGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. It can also be used with the SK312 Companionway Mount for positioning sailing instruments above the companionway. Features: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets