7610 120 Amp SI-Series Automatic Charging Relay Allows temporary isolation of house loads from engine circuit during engine cranking to protect sensitive electronics Automatically combines battery banks during the charging cycle and isolates under discharge 12/24 Volt auto ranging voltage input Waterproof rated IP67 - temporary immersion for 30 minutes Ignition protected - safe for installation aboard gasoline powered boats Remote LED output indicates relay state away from ACR LED light indicates when batteries are combined LED blinks in undervoltage lockout and starting lockout Supports high-output alternators up to 120 Amperes Included with the ADD A BATTERY Dual Circuit System Automatically combines battery banks during the charging cycle and isolates under discharge Ignition protected - safe for installation aboard gasoline-powered boats Activates from any charging source - alternators, battery chargers, or solar panels Hermetically sealed contacts / vaporproof Side and bottom knockouts for power cable connections Clip-on cover protects and insulates terminal connections Tin-plated copper studs for maximum corrosion resistance 7/8" (22.22mm) stud length to accept multiple cable terminals 1/4" x 0.031" male quick connect terminals for ground and remote LED and starting interrupt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Add-A-Battery 7650 The 7650 Add-a-Battery simplifies switching and automates charging for a complete two battery bank management solution. A complete two battery bank management solution Dual Circuit Plus™ Battery Switch isolates engine and house circuits, and combines battery banks for emergency starting The 120 Amp SI ACR automatic charging relay combines for charging WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

7650 Add-A-Battery Kit - Boxed Packaging The 7650 Add-a-Battery simplifies switching and automates charging for a complete two battery bank management solution. Features: A complete two battery bank management solution Dual Circuit Plus Battery Switch isolates engine and house circuits, and combines battery banks for emergency starting The 120 Amp SI ACR automatic charging relay combines for charging WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Programmable Automatic Charging Relay (ACR) 160A, 12V This 160A Egis charging relay is automatic and programable. The relay eliminates dead start batteries by sharing charging on either of two batteries and isolating batteries when no charge sources are present. Applications: Supports multiple engines or independent charge systems by incorporating two independent start or engine isolation inputs to allow isolation of charge sources when both are active to maximize charging performance. Protects Electrical System Cascading Faults with an optional lock-out from closing if one terminal is connected to a battery with a shorted cell. Features: Ultra-Low Power Draw Compared to typical ACRs (7-10 mA) vs 7610 ACR @ 1.3 mA, will not deplete batteries even after extended electrical system downtime. Simple and robust installation - The integrated sealed plug eliminates corrosion and includes a Deutsch/Amphenol DTM connector harness Start Assist input option to ensure maximum cranking amps are available by allowing the manual connection of batteries via a remote switch. Bullet-proof construction - Sealed unit, stainless steel hardware, and high-temperature materials allow mounting anywhere. Integrated thermal overload shutdown protection. Additional low-amp output can be used to report device status remotely or drive a secondary relay for charging a battery bank without a charge source (see example) Specifications: Continuous Current (Amps): 160 Voltage Range: 8-18 VDC Off-State Current Draw mA: 1.3 Interrupt Current (Amps): 240 ACR Closing Voltage (VDC): 12.9-13.6 ACR Opening Voltage (VDC): 12.1-12.8 Focal Features: Top Side Dip Switches Accessible after mounting for programming voltage settings and determining active features. Protected by self-retained cover. Stainless Steel Self-Locking Hardware 100% Non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking. Integral I/O Connector Sealed Molex MX-150 connector eliminates the susceptibility to corrosion and vibrating loose of 1/4" quick connect terminals on competitive products. Connection Options Comes standard with a Deutsch DT/AT style connector harness. Provides three connection options (MX-150, DT/AT, and wire leads). Easy Integration with RT Fuse Blocks (24 HR Circuits) Optional EasyLink bus bars reduce the space and cost of connecting TH Series relays with RT Series Fuse Blocks. LED Diagnostics Provides an indication of pending relay ON/OFF, under voltage, over voltage/temp, start isolation/assist, and output on/off status.

Automatic Charging Relay Plus - 160A - 24V This 160A Egis automatic charging relay eliminates dead-start batteries by sharing charging on either of two batteries and isolating batteries when no charge sources are present. Applications:  Supports multiple engines or independent charge systems by incorporating two independent start or engine isolation inputs to allow isolation of charge sources when both are active to maximize charging performance Protects Electrical System Cascading Faults with an optional lock-out from closing if one terminal is connected to a battery with a shorted cell Features: Ultra-low power draw compared to typical ACRs (7-10 mA) vs. the 7610 ACR @ 1.3 mA will not deplete batteries even after extended electrical system downtime. Simple and robust installation - integrated sealed plug eliminates corrosion; includes Deutsch/Amphenol DTM connector harness Start to assist input option to ensure maximum cranking amps are available by allowing manually connecting batteries via a remote switch Bullet-proof construction - sealed unit, stainless steel hardware, and high-temperature materials allow mounting anywhere; Integrated thermal overload shutdown protection Additional low-amp output can be used to report device status remotely or drive a secondary relay for charge to a battery bank without a charge source (see examples) Specifications: Continuous Current Amps: 160 Voltage Range (VDC): 16 – 36 Off-State Current Draw (mA): 1.3 Interrupt Current (Amps): 240 AC Closing Voltage Range (VDC): 25.8-27.2 AC Opening Voltage Range (VDC): 24.2-25.6 Focal Features: Top Side Dip Switches Accessible after mounting for programming voltage settings and determining active features. Protected by self-retained cover. Stainless Steel Self-Locking Hardware 100% non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking. Integral I/O Connector Sealed Molex MX-150 connector eliminates the susceptibility to corrosion and vibrating loose of 1/4" quick connect terminals on competitive products. Connection Options Comes standard with a Deutsch DT/AT style connector harness. Provides three connection options (MX-150, DT/AT, and wire leads).  Easy Integration with RT Fuse Blocks (24 HR Circuits) Optional EasyLink bus bars reduce the space and cost of connecting TH Series relays with RT Series fuse blocks.  LED Diagnostics Indicates pending relay ON/OFF, under voltage, over voltage/temp, start isolation/assist, and output on/off status.

7611 DC BatteryLink™ Automatic Charging Relay - 120 Amp w/Auxiliary Battery Charging Features: 120 Amp continuous rating 12/24V DC auto ranging voltage input Senses charging on two battery banks Side and bottom knockouts for cable connections Clip-on cover insulates terminal connections 7/8" (22 mm) stud length to accept multiple cable terminals Integrated LED indicates ACR status 1/4" x .032" male quick connect terminals for ground and optional features Specifications: Intermittent Rating: 5 min.: 210 Amps Continuous Rating: 120 Amps Nominal Voltage: 12/24 Volts DC WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

7601 DC Mini ACR Automatic Charging Relay - 65 Amp Features: 65 Amp continuous rating manages the charging current from alternators up to 65 Amps found on most outboards and many inboard engines Compact case design allows surface and panel mounting Senses charging on two battery banks Snap-on cover insulates terminal connections LED indicates ACR status 1/4" x .032" male quick connect terminal for ground 5/8" (16 mm) stud length to accept multiple cable terminals 12V DC voltage input Specifications: Intermittent Rating: 5 min.: 115A Terminal Stud Size: 1/4"-20 Relay Contact Position: Open (30 sec.): 12.75V DC Continuous Rating: 65A Maximum Torque: 75 in-lb (8.5 Nm) Relay Contact Position - Open High: 16.0V DC Amperage Operating Current: 175mA (Combine) Relay Contact Position: Combine (30 sec.): 13.0V DC Under Voltage Lockout: 9.5V DC Amperage Operating Current: 15mA (Open) Relay Contact Position: Combine (2 min.): 13.6V DC Maximum Cable Size: 1/0 AWG Relay Contact Position: Open (10 sec.): 12.35V DC WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

7621 Manual Control: No Coil Voltage: 24V DC Combines battery banks during charging and isolates under discharge 500 Ampere continuous rating suitable for use with large battery banks, starters, alternators, and inverter/chargers Can be remotely combined with optional switch Silver alloy contacts provide high reliability 3/8" copper studs, using Blue Sea Systems superior one piece stud technology, suitable for 300 Ampere continuous rating and large cable connections WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

7620 Manual Control: No Coil Voltage: 12V DC Combines battery banks during charging and isolates under discharge 500 Ampere continuous rating suitable for use with large battery banks, starters, alternators, and inverter/chargers Includes ML-Series Remote Control Contura Switch PN 2146 Silver alloy contacts provide high reliability 3/8" copper studs, using Blue Sea Systems superior one piece stud technology, suitable for 300 Ampere continuous rating and large cable connections WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Remote Control Panel w/(2)2145 & (1)2146 Remote Control Contura Switch Features: Lockout slides reduce the risk of accidental switching For use with two ML-Series Switches and one ML-Series Automatic Charging Relay Includes labels illustrated only Over 500 individual labels available Specifications: Positions:3 Nominal Voltage:12V DC / 24V DC Height:4.75" (120.65mm) Width: 4.88" (123.95mm) Depth:2.00" (50.8mm) Weight:0.83lb (0.38kg) Included: (2) - 2145 - SPDT Remote Control Contura Switch - (ON)-OFF-(ON) (1) - 2146 - SPDT Remote Control Contura Switch - ON-OFF-ON WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

m-Series Dual Circuit Plus PN 6011 (1) 100A C-Series Flat Rocker Circuit Breaker (2) 15A Push Button Thermal Circuit Breakers Designed for twin engine configurations Provides 24 hour circuit protection Provides main DC circuit protection in addition to high ampere load protection Protects electronics from sags and spikes caused by engine cranking Allows emergency cross connect between isolated battery banks Isolates the Engine circuit from the House circuit Simplifies battery switch operation Allows independent battery discharge Addition of an Automatic Charging Relay automates charging both batteries Includes 4218 - Square Format Labels and 4140 - 24 Hour Round Labels WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

160A Automatic Charge Isolator - 12V or 24V The ACR-160 combines battery banks for charging and isolates them when charging has stopped. It provides priority for charging only the starter battery first and protects from excessive discharging of the starter battery. The Automatic Charge Isolator is also referred to as a battery separator, battery isolator or an automatic charging relay. Features: Microprocessor controlled, dual sensing Easy to install - does not require charging the existing circuit of the alternator Potted, waterproof, sealed unit Low standby current Automatic detection of 12 or 24 VDC systems 160 Amp continuous rated, 480 Amp peak (250 msec) Monitoring of relay activation by external LED Over voltage protection Specifications: Input: 12/24 VDC Output: 12/24 VDC Amps: 160 Warranty: 2 Year Limited Applications: Marine Automotive Recreational WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

8080 Single Circuit ON/OFF - Plus Main  Installed Components: 2 6006 m-Series Switches 1 100A c-Series Flat Rocker Circuit Breaker Features: Isolates batteries and provides DC main circuit protection Ignition protected - Safe for installation aboard gasoline powered boats Isolates the Engine circuit from the House circuit Simplifies battery switch operation Protects electronics from sags and spikes caused by engine cranking Discharges batteries independently Addition of an Automatic Charging Relay automates charging of both batteries Enables a failed Start battery to be isolated from the electrical system and both House and Start loads to be operated from the remaining battery bank Provides main circuit protection for DC House power system Enables a failed House or Start battery bank to be isolated from the electrical system and both House and Start loads to be operated from the remaining battery bank Simplifies battery switch operation Isolates Start circuit from House circuit Protects electronics from sags and spikes caused by engine cranking Ignition protected - Safe for installation aboard gasoline-powered boats Addition of an Automatic Charging Relay automates charging both batteries Allows independent battery discharge WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

BatteryLink® Charger - 10Amp - 2-Bank Charge two batteries at or away from the dock with a 10A multistage battery charger and integrated 65A Automatic Charging Relay (ACR) AC charging at the dock: Use AC shore power to charge two isolated battery banks with the 3 Stage 10 Amp battery charger DC charging away from the dock: Share the DC power from the alternator with both the Start and the Auxiliary battery through the integrated 65A ACR Battery Temperature Compensation prolongs battery life Start isolation protects sensitive electronics from voltage sags and spikes Includes LED remote indicator for charge status at the helm Snap-on insulating cover One-piece stainless flange nuts ensure safe and secure connections Specifications Total Output Current: 10A Nominal Voltage: 12V DC Number of Outputs: 1 negative / 2 positive Terminal Stud Torque: 60 in-lb (6.78 Nm) Continuous Rating:65A Intermittent Rating:115A Universal AC Input Voltage: 90-265V AC AC Input Frequency: 50/60Hz Typical Float Voltage:13.5V DC Battery Types: AGM / Flooded / TPPL - Do not mix battery types Cable Size to Meet Ratings:10 AWG Negative Cable / 6 AWG Positive Cable Maximum Battery CCA: 850CCA Maximum Cable Size: 1/0 AWG (50mm) Operating Current: 10mA (No AC Power, ACR Open) / 60mA (No AC Power, ACR Closed) Recommended Battery Bank Sizes: 60Ah Minimum Terminal Stud Size:1/4"-20 (accepts M6 ring terminal) Warranty: 5 Year Combine 30 sec: 13.5V Combine 2 Min: 13.0V Open 10 sec: 12.35V Open 30 sec: 12.75V WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Mini Add-A-Battery Plus Kit - 10A A complete small boat battery management system. Charge two batteries at or away from the dock. For alternators up to 65A Includes a Dual Circuit Plus™ Battery Switch 6011 a 3 Stage, 10 Amp charger with an integrated 65A Automatic Charging Relay, and a LED charger remote mSeries Dual Circuit Plus™ Battery Switch Switches two battery banks simultaneously while maintaining battery bank isolation Can combine two battery banks in the event of a low start battery IP66 - protected against powerful water jets BatteryLink® Charger Integrated ACR provides DC charging from engine alternator AC plug-in while at the dock Battery temperature compensation prolongs battery life Includes a remote LED indicator Start isolation protects sensitive electronics from voltage sags and spikes IP67 - protected against immersion up to 1M for 30 minutes WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.