March 809 815 Series Mag-Drive Centrifugal Pumps The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze with Base 24VDC High Speed 7.5GPM 1/2"MPT Ports  

Applications for the 809-BR-HS 12V Magnetic Drive Pump include hot water systems and solar heating.   March Pump's industrial 809-BR-HS 12V & 24V is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 6 gallons per minute at 2.5 feet, and its maximum head is 15.5 Feet (or around 6.5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 inch male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 0.04 Horsepower DC Brush Type Motor, available in 12 or 24 Volts.  The 12 Volt motor has an operating range from 0 to 14 Volts, and the 24 Volt motor has an operating range from 0 to 26 Volts.  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.     Max Flow 6 GPM 22.7 LPM Max Head 15.5 FT 4.7 M Power .04 HP .029 KW Electrical 12V Range 0-14 or 24V Range 0-26     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Bronze (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

March 809 815 Series Mag-Drive Centrifugal Pumps Bronze Center Inlet 115V 4.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March Mag-Drive Centrifugal Pumps Bronze Center Inlet 12VDC 5.5GPM     The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March MDX-3 5/8 Pump 115V Motor 5/8" Ports

March Mag-Drive Centrifugal Pump With 1/8Hp Air Motor • Simple, versatile and reliable, March AC-3CP-MD and BC-3CP-MD Series pumps feature an “orbital” magnetic drive and leak-proof design. They are rated up to 10 GPM (33 LPM) flow and for heads up to 20.5 ft (4.5 m) (39 ft. [13 m] when driven by an air motor). • Typical applications include film processors, ice makers, laboratory and medical equipment, vapor degreasers and marine air conditioning systems. • All screws are type 18-8 stainless. The O-ring gasket is Buna-N rubber on AC models and Viton on BC models. The stationary spindle is ceramic. All plastic parts are Glass Filled Polypropylene Plastic. The thrust washer is ceramic. The Impeller Magnet is encased in Polypropylene on the BC models. • Series AC-3CP-MD pumps are driven by 1/15 HP (.018 kw), 3200 (60 Hz, air cooled). Series BC-3CP-MD are 3450 rpm (50/60 Hz, blast-cooled), all motors are ball bearing motors. Air motors rated at 1/8 HP (.093 kw) are also available for certain environments. The 230-volt motors are all rated 50/60 Hz.      March Pump Mag-Drive Centrifugal Pump Air Motor 10GPM 3/4"FPT Inlet, 1/2"MPT Outlet

March 809 BR HS Mag-Drive Centrifugal Pump Bronze 24V Pump The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze 24VDC High Speed 7.5GPM 1/2"MPT Ports  

March 809-BR-HS 12V Mag Drive Pump Applications for the 809-BR-HS 12V Magnetic Drive Pump include hot water systems and solar heating.   March Pump's industrial 809-BR-HS 12V & 24V is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 6 gallons per minute at 2.5 feet, and its maximum head is 15.5 Feet (or around 6.5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 inch male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 0.04 Horsepower DC Brush Type Motor, available in 12 or 24 Volts.  The 12 Volt motor has an operating range from 0 to 14 Volts, and the 24 Volt motor has an operating range from 0 to 26 Volts. The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.   Max Flow 6 GPM 22.7 LPM Max Head 15.5 FT 4.7 M Power .04 HP .029 KW Electrical 12V Range 0-14 or 24V Range 0-26     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Bronze (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

Applications for the 809-BR-HS Magnetic Drive Pump include hot water systems and solar heating.   March Pump's industrial 809-BR-HS is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 6 gallons per minute at 2 feet, and its maximum head is 12 Feet (or around 5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.     Unit System 60Hz 50Hz Max Flow 6 GPM 18.9 LPM Max Head 12.1 FT 2.5 M Power .04 HP .029 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Bronze (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

March 815 Series Mag-Drive Centrifugal Pumps The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. •  Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. •  Maximum liquid temperature for the 809 and 815 series is 250 F. •  Port configurations include in-line and center inlet with side discharge. •  Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. •  There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze 230V High Speed 7.2GPM 1/2"MPT Ports    

Applications for the MDX-3-1/2 Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.    March Pump's industrial MDX-3-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 8 gallons per minute at 1 foot, and its maximum head is 19 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, carbon filled Kynar (PVDF), Ryton Buna N, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheitor 87 Celsius. The March MDX-3-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 8.5 GPM 30 LPM Max Head 19 FT 4 M Power .04 HP .029 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front Housing and Impeller), Carbon filled Kynar (Rear Housing, Shaft), Ryton (Thrust Washer), Buna N (O-Ring), Stainless Steel (Screw) Ceramic Magnet    

March 815-BR Magnetic Drive Pump for Hot Water systems and Solar Heating. March Pump's industrial 815-BR is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 7 gallons per minute at 5 feet, and its maximum head is 18.6 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.   Max Flow: 7 GPM or 22.7 LPM Max Head: 18.6 FT or 4.1 M Power: .04 HP or.029 KW Electrical: 115V 50/60HZ or 230V 50/60HZ     Type: Magnetic Drive Centrifugal Pump Inlet: 1/2"MPT Outlet: 1/2"MPT Wet End: Bronze (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

March 815-BR Magnetic Drive Pump for Hot Water Systems and Solar Heating March Pump's industrial 815-BR is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 7 gallons per minute at 5 feet, and its maximum head is 18.6 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.   Max Flow: 7 GPM or 22.7 LPM Max Head: 18.6 FT or 4.1 M Power: .04 HP or .029 KW Electrical: 115V 50/60HZ or 230V 50/60HZ   Type: Centrifugal Mag Drive Inlet: 1/2"MPT Outlet: 1/2"MPT Wet End: Bronze (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

March TE-MDK-MT3 Magnetic Drive Pump Applications for the TE-MDK-MT3 Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.   The TE-MDK-MT3 has pumped Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Hydrochloric Acid (Muriatic), Hydrofluoric Acid, Hydrogen Peroxide, Nitric Acid, Phosphoric Acid, Potassium Chloride, Sodium Chloride, Sodium Hypochlorite, Sulfuric Acid, Fresh Water, Salt Water, DI Water, and many more chemicals.   Type: Centrifugal Mag Drive Inlet: 1/2"MPT Outlet: 1/2"MPT Wet End: Carbon filled Kynar (Front and Rear Housing, Impeller), Ceramic (Shaft, Thrust Washer), Viton (O-Ring)   March Part Number 0135-0088-0300     Unit 60HZ 50HZ System US Metric US Metric Max Flow 10 GPM 37.9 LPM 9.2 GPM 35 LPM Max Head 17 FT 5.1 M 12.1 FT 3.7 M Power .066 HP .05 KW .066 HP .05 KW Electrical 1Ph 115/230V 50/60HZ

March TE-MDX-MT3 Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.   March magnetic drive 10 gpm/35 lpm chemical pump having 1/2" MPT inlet size and 1/2" MPT outlet size features 75 psi maximum pressure and 115/230 VAC voltage rating   March Pump's industrial TE-MDK-MT3 is an American sealless centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 10 gallons per minute at 1 foot, and its maximum head is 17 feet (or around 7PSI). The standard wet end (the materials that come into contact with the solution) is composed of carbon filled Kynar (PVDF), viton, and ceramic. The inlet connection is 1/2 in male pipe thread, and the outlet is 1/2 in male pipe thread. The standard motor is a 1 phase 115 V or 230V 0.04 horsepower fan cooled motor, which can be run on either 50 or 60 hertz. The maximum internal pressure the pump can tolerate is 75PSI, and the maximum liquid temperature is 200 Fahrenheit or 93 Celsius. The March TE-MDK-MT3 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Totally enclosed fan cooled Series MDX and MDK are centrifugal magnetic drive pumps, eliminating the need for a shaft seal Pumps can be serviced with a screwdriver Item: Chemical Pump Type: Magnetic Drive Series: MDX Flow Rate: 10 gpm at 60 Hz, 35 lpm at 50 Hz Inlet Size: 1/2 in MPT Outlet Size: 1/2 in MPT Voltage Rating: 115/230 VAC Motor Specifications: 1-Phase, 50/60 Hz, 0.066 hp, 95/115 W, 2850/3450 rpm Maximum Head: 17 ft at 60 Hz, 3.7 m at 50 Hz Maximum Pressure: 75 psi Temperature Rating: 93 deg C Material: Ryton Dimensions: 12.42 in Length x 8.02 in Width x 7.19 in Height