March Pump- Mag-Drive Centrifugal 115V Pump 1X3/4 Smooth Ports • March AC-4C-MD and BC-4C-MD series pumps can deliver a maximum flow of 14 GPM (50 LPM), and are capable of serving applications with a maximum head of 21.5 ft. (4.7 m) (49 ft. [15.6 m] when driven by an air motor). • Applications include electronic medical equipment, etching machines, photo processing equipment, hospital thermal blankets and food heating cabinets. • Standard construction is of polypropylene, with optional wetted materials that include Ryton or Kynar. Other materials include: Ceramic, Buna N rubber, and Viton for total chemical compatibility. • Drive choices are a 1/12 HP (.062 kw), 3450 rpm air cooled or a 1/10 HP (.074 kw) 3450 rpm blast-cooled, 115-volt single phase, 50/60 Hz. motor. 230 volt optional.      March Pump Mag-Drive Centrifugal Pump 115V Air Cooled 14GPM 1" Hose Inlet, 3/4" Hose Outlet

The March 320-AP-MD has the durability for continuous duty in applications requiring low flow and high head.  Typical applications include laser cooling, medical systems, filter systems, and various processing equipment in the electronics industry.    March Pump's industrial 320-AP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 3.3 gallons per minute at 1 feet, and its maximum head is 40 Feet (or around 17PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, and Ceramic. The inlet connection is 0.5 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.083 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March 320-AP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 3.3 GPM 11.3 LPM Max Head 40 FT 8.8 M Power .083 HP .062 KW Electrical 115V 50/60HZ or 230V 50/60Z     Type Centrifugal Mag Drive Inlet 5/8"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft and Thurst Washer) Motor Options Air Cooled or Blast Cooled

March Mag-Drive Centrifugal Pump With 1/8Hp Air Motor • Simple, versatile and reliable, March AC-3CP-MD and BC-3CP-MD Series pumps feature an “orbital” magnetic drive and leak-proof design. They are rated up to 10 GPM (33 LPM) flow and for heads up to 20.5 ft (4.5 m) (39 ft. [13 m] when driven by an air motor). • Typical applications include film processors, ice makers, laboratory and medical equipment, vapor degreasers and marine air conditioning systems. • All screws are type 18-8 stainless. The O-ring gasket is Buna-N rubber on AC models and Viton on BC models. The stationary spindle is ceramic. All plastic parts are Glass Filled Polypropylene Plastic. The thrust washer is ceramic. The Impeller Magnet is encased in Polypropylene on the BC models. • Series AC-3CP-MD pumps are driven by 1/15 HP (.018 kw), 3200 (60 Hz, air cooled). Series BC-3CP-MD are 3450 rpm (50/60 Hz, blast-cooled), all motors are ball bearing motors. Air motors rated at 1/8 HP (.093 kw) are also available for certain environments. The 230-volt motors are all rated 50/60 Hz.      March Pump Mag-Drive Centrifugal Pump Air Motor 10GPM 3/4"FPT Inlet, 1/2"MPT Outlet

March Mag-Drive Centrifugal Pump Plastic 230V Hi Speed  Beer Pump The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   Unit System 60Hz 50Hz Max Flow 6 GPM 18.9 LPM Max Head 12.1 FT 2.5 M Power .04 HP .029 KW Electrical 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller) Can handle liquids of 250F Materials are FDA Food Compliant With 6 Foot Cord and Plug Components are UL Recognized American Made          

March Pump Mag-Drive Centrifugal Pump Kynar Single Phase 2Hp  • March TE-7.5K-MD Series pumps are the only ones in the March product line with all molded parts constructed of natural Kynar. This makes them ideal for super sensitive applications where even a trace of foreign matter is unacceptable, such as microchip manufacturing. Various bushing materials are available for such applications where purity of solutions is critical. • Flow rates range from 10 GPM (35 LPM) minimum to 82 GPM (268 LPM) maximum. Head ranges from 0 ft. to a maximum of 85 ft. (18m). Other application examples include plating equipment and D.I. water systems. • Standard with the March TE-7.5K-MD Series pump is a 2 HP (1.49 kw), 230/460-volt, three-phase, totally enclosed motor. Severe duty and explosion-proof motors are also available. Standard port configuration is a 2" MPT inlet with a 1 1/2" MPT outlet. • All plastic parts of the pump are molded out of natural Kynar (PVDF). The stationary spindle and Thrust Washers are made of porcelain ceramic. The O-ring for the housing is Viton rubber. The bushings in the impeller Assembly are carbon. There are no other materials in contact with the solution.    March Pump Mag-Drive Centrifugal Pump Kynar 115/230V 2HP TEFC 82GPM 2"MPT Inlet, 1 1/2"MPT Outlet

Applications for the 809-BR Magnetic Drive Pump include hot water systems and solar heating.    March Pump's industrial 809-BR is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 4.5 gallons per minute at 0.5 feet, and its maximum head is 4.3 Feet (or around 1.8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.01 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.     Unit System 60Hz 50Hz Max Flow 4.5 GPM 10.3 LPM Max Head 4.3 FT .92 M Power .01 HP .007 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Bronze (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

March 815 Series Mag-Drive Centrifugal Pumps The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. •  Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. •  Maximum liquid temperature for the 809 and 815 series is 250 F. •  Port configurations include in-line and center inlet with side discharge. •  Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. •  There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze 230V High Speed 7.2GPM 1/2"MPT Ports    

March Mag-Drive Centrifugal Pumps Bronze 230V High Speed 4.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 230V High Speed 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March 809 BR HS Mag-Drive Centrifugal Pump Bronze 24V Pump The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze 24VDC High Speed 7.5GPM 1/2"MPT Ports  

March 809 PL Magnetic Drive Centrifugal Pump The March 809-PL is used to pump Cutting Oils, Ethylene Glycol, Hot Water, Hot Wort and Salt Water March Pump's industrial 809-PL is an American seal-less centrifugal magnetic drive pump ideal for applications such as home brewing and hot water systems. It is capable of generating a maximum flow of 4.5 gallons per minute at 0.5 feet, and its maximum head is 4.3 Feet (or around 1.8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.01 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50 PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius Unit System 60Hz Max Flow 4.5 GPM Max Head 4.3 FT Power .01 HP Electrical 115V 60HZ      Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Polysulfone (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

March MDX-3 5/8 Pump 115V Motor 5/8" Ports

March 809 BR 12VDC Applications for the 809-BR 12V & 24V Magnetic Drive Pump include hot water systems, refrigeration systems and solar heating.   March Pump's industrial 809-BR 12V & 24V is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 5 gallons per minute at 1.5 feet, and its maximum head is 7 Feet (or around 3PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 0.01 Horsepower DC Brush Type Motor, available in 12 or 24 Volts.  The 12 Volt motor has an operating range from 0 to 14 Volts, and the 24 Volt motor has an operating range from 0 to 26 Volts. The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.   Max Flow 5 GPM 18.9 LPM Max Head 7.1 FT 2.1 M Power .01 HP .007 KW Electrical 12V Range 0-14 or 24V Range 0-26  

March TE-5.5C-MD 1 Phase Mag Drive Pump with Explosion Proof Motor   Applications for the TE-5.5C-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.     March Pump's industrial TE-5.5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ryton/Teflon/Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March TE-5.5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 30 GPM 102 LPM Max Head 41 FT 9 M Power .33 HP .248 KW Electrical 1PH 115/230V                  3PH 230/460V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 3/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers) Motor Options Explosion Proof

March TE-5.5S-MD Mag Drive Pump 115 volts Applications for the March TE-5.5S-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners. The March TE-5.5S-MD has pumped Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Potassium Chloride, Potassium Hydroxide, Sodium Chloride, Sodium Hydroxide (Caustic Soda), Fresh Water, Salt Water, and many more chemicals.  The TE-5.5S-MD may have been modified to handle these chemicals.   March Pump's industrial TE-5.5S-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of 316 Stainless Steel, Viton, Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 200PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius. The March TE-5.5S-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Unit System 60Hz 50Hz Max Flow 30 GPM 102 LPM Max Head 41 FT 9 M Power .33 HP .248 KW Electrical 1PH 115/230V    3PH 230/460V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 3/4"MPT Wet End 316 Stainless Steel (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers), Carbon (Bushing)

Applications for the MDX-3-1/2 Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.    March Pump's industrial MDX-3-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 8 gallons per minute at 1 foot, and its maximum head is 19 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, carbon filled Kynar (PVDF), Ryton Buna N, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheitor 87 Celsius. The March MDX-3-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 8.5 GPM 30 LPM Max Head 19 FT 4 M Power .04 HP .029 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front Housing and Impeller), Carbon filled Kynar (Rear Housing, Shaft), Ryton (Thrust Washer), Buna N (O-Ring), Stainless Steel (Screw) Ceramic Magnet