|
For 2 or 3-wire configurations of: 12V, 24V, 12/24V, 24/36V, or 36V Systems. Water-tight sealing cap and O-ring seal. Corrosion resistant, plated-brass electrical components. Standard 1 1/8" diameter mounting hole for easy installation. Mounting plate and locking ring for front and rear access installation. Easily replaces other trolling motor receptacles. Can be used for many other DC applications. Max amp rating of 62A @ 36VDC when used with Sierra WH10620P Plug. Accepts 16 to 6 AWG wire without the need of an expensive adapter.
|
65.99 |
|
|
For 2 or 3-wire configurations of: 12V, 24V, 12/24V, 24/36V, or 36V Systems. Water-tight sealing cap and O-ring seal. Corrosion resistant, plated-brass electrical components. Standard 1 1/8" diameter mounting hole for easy installation. Mounting plate and locking ring for front and rear access installation. Easily replaces other trolling motor receptacles. Can be used for many other DC applications. Max amp rating of 62A @ 36VDC when used with Sierra WH10620P Plug. Accepts 16 to 6 AWG wire without the need of an expensive adapter.
|
38.49 |
|
|
For 2 or 3-wire configurations of: 12V, 24V, 12/24V, 24/36V, or 36V Systems. Water-tight sealing cap and O-ring seal. Corrosion resistant, plated-brass electrical components. Standard 1 1/8" diameter mounting hole for easy installation. Mounting plate and locking ring for front and rear access installation. Easily replaces other trolling motor receptacles. Can be used for many other DC applications. Max amp rating of 62A @ 36VDC when used with Sierra WH10620P Plug. Accepts 16 to 6 AWG wire without the need of an expensive adapter.
|
32.99 |
|
|
Groco K-3-R Piston Ring Set (2)
|
10.53 |
|
|
ConnectPro® 3-Wire Receptacle
Features:
Universal design for 2 or 3-wire configuration 12, 24, 12/24, 24/36 or 36 volt systems
Watertight sealing cap
Corrosion resistant, plated brass electrical components
Drain holes in receptacle keep water away from electrical components
Perma-Lock screw terminals will not loosen under extreme hull vibrations
Standard 1-1/8" diameter mounting hole
Easy to install, with supplied mounting plate for front panel installation, or locking ring for rear access installation
Accepts 10 and 8 gauge wire
Easily replaces other trolling motor plugs and receptacles
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
23.08 |
|
|
ConnectPro® Charging/Trolling System Receptacle & Plug
ConnectPro® Receptacle
Universal design for 2 or 3-wire configuration 12, 24, 12/24, 24/36 or 36 volt systems
Watertight sealing cap
Corrosion resistant, plated brass electrical components
Drain holes in receptacle keep water away from electrical components
Perma-Lock™ screw terminals will not loosen under extreme hull vibration
Standard 1-1/8" diameter mounting hole
Easy to install, with supplied mounting plate for front panel installation, or locking ring for rear access installation
Accepts 10 and 8 gauge wire
Easily replaces other trolling motor plugs and receptacles
ConnectPro® Plug
O-ring seal for waterproof connections
Weather resistant plug cover
Corrosion resistant, plated brass electrical components
Accepts 16 to 8 gauge wire
Ergonomic contoured grip for easy hook-up and ground blade alignment
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
42.61 |
|
|
ConnectPro® Charging/Trolling Receptable, Plug & 6-Guage Adapter
The ConnectPro® system features locking plug and receptacle and spring clamping connection, which provide a secure electrical contact.
Receptacle is universal design for 2-or-3 wire configuration, 12, 24, 12//24, 24//36 or 36 volt systems.
Features:
Watertight sealing cap
Corrosion resistant, plated brass electrical components with drain holes in receptacle to keep water away from electrical components
Standard 1-1/8 diameter mounting hole and accepts up to 8 gauge wire
Includes mounting plate
Plug has O-ring seal for waterproof connections
Weather resitant plug cover
Accepts 16 to 8 gauge wire
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
54.44 |
|
|
Medium-Duty Trolling Motor Receptacle
MotorGuide's Medium-Duty Trolling Motor Receptacle is compatible with 12,
24 and 36 volt trolling motors. Universal design for 2 or 3-wire
configuration. Standard 1-1/8" diameter mounting hole. Watertight sealing
cap. Drain holes in receptacle keep water away from electrical components.
Accepts 8 and 10 gauge wire.
Corrosion resistant
Plated brass electrical components
Easy to install
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
21.59 |
|
|
RayMic Wireless Handset - Only*
*Wireless hub (A80540) required – sold separately
Optional wireless handset
Add up to 2 or 3 wireless handsets to the VHF system
Wireless hub carries both data and audio to and from your wireless handset stations
Waterproof construction
Oversized LCD and rubberized keypads
Built-in lithium ion rechargeable battery for long life with the latest inductive charging technology – no charging port or cable to plug in!
Wireless base station pairs to active speaker
Handset features smart locator alarm – activate alarm from hub
Please see MFG Part Number T70433 to purchase the mic & hub together
|
396.18 |
|
|
Ampco Pumps AC114MD56C-3.75 Peo 1 1/2 X 1 1/2 Kit 3.75
|
1668.60 |
|
|
50A Battery Charger - 12V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor
This advanced fully automatic three-stage 50 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 2 separate battery banks.
Features:
Switch mode technology for high efficiency, lightweight and quiet operation
Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell
Can charge 2 banks of batteries simultaneously, no isolator necessary
Can be used as a power supply or DC UPS when used in conjunction with a battery
User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz
User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of stand-alone and loaded Lead Acid Batteries
“Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries
Voltmeter and Ammeter for monitoring
Fan cooled based on output current
Protections: Short circuit, overload, reverse battery connection and over temperature
Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively
Specifications:
Input: 120 VAC 60 Hz or 230 VAC 50 Hz
Output: 12 VDC
Amps: 50
Remote Control: 900-RC
Weight: 9.0 (lbs)
Weight: 4.1 (kg)
Dimensions: 13.03 x 9.60 x 3.82 (in)
Dimensions: 331 x 244 x 97 (mm)
Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B
Warranty: 2 Year Limited
Applications:
Automotive
Recreational vehicles
Marine
Communications sites
Battery back-up systems
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
445.22 |
|
|
80A Battery Charger - 12V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor
This advanced fully automatic three-stage 80 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 2 separate battery banks.
Features:
Switch mode technology for high efficiency, lightweight and quiet operation
Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell
Can charge 2 banks of batteries simultaneously, no isolator necessary
Can be used as a power supply or DC UPS when used in conjunction with a battery
User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz
User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of standalone and loaded Lead Acid Batteries
“Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries
Voltmeter and Ammeter for monitoring
Fan cooled based on output current
Protections: Short circuit, overload, reverse battery connection and over temperature
Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively
Specifications:
Input: 120 VAC 60 Hz or 230 VAC 50 Hz
Output: 12 VDC
Amps: 80
Remote Control: 900-RC
Weight: 9 (lbs)
Weight: 4.1 (kg)
Dimensions: 15 x 9.61 x 3.82 (in)
Dimensions: 381 x 244 x 97 (mm)
Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B
Warranty: 2 Year Limited
Applications:
Automotive
Recreational vehicles
Marine
Communications sites
Battery back-up systems
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
632.32 |
|
|
25A Battery Charger - 24V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor
This advanced fully automatic three-stage 25 Amp battery charger is ideal for charging all types of 24 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit, reverse polarity and thermal overload protection. The unit allows charging of up-to 2 separate battery banks.
Features:
Switch mode technology for high efficiency, lightweight and quiet operation
Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell
Can charge 2 banks of batteries simultaneously, no isolator necessary
Can be used as a power supply or DC UPS when used in conjunction with a battery
User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz
User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of standalone and loaded Lead Acid Batteries
“Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries
Voltmeter and Ammeter for monitoring
Fan cooled based on output current
Protections: Short circuit, overload, reverse battery connection and over temperature
Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively
Specifications:
Input: 120 VAC or 230 VAC
Output: 24 VDC
Amps: 25
Remote Control: 900-RC
Weight: 9 (lbs)
Weight: 4.1 (kg)
Dimensions: 13.03 x 9.6 x 3.82 (in)
Dimensions: 331 x 244 x 97 (mm)
Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B
Warranty: 2 Year Limited
Applications:
Test bench
Automotive
Marine
Communications sites
Battery back-up systems
Hobby
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
441.41 |
|
|
40A Battery Charger - 24V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor
This advanced fully automatic three-stage 40 Amp battery charger is ideal for charging all types of 24 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 2 separate battery banks.
Features:
Switch mode technology for high efficiency, lightweight and quiet operation
Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell
Can charge 2 banks of batteries simultaneously, no isolator necessary
Can be used as a power supply or DC UPS when used in conjunction with a battery
User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz
User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of standalone and loaded Lead Acid Batteries
“Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries
Voltmeter and Ammeter for monitoring
Fan cooled based on output current
Protections: Short circuit, overload, reverse battery connection and over temperature
Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively
Specifications:
Input: 120 VAC or 230 VAC
Output: 24 VDC
Amps: 40
Remote Control: 900-RC
Weight: 9 (lbs)
Weight: 4.1 (kg)
Dimensions: 15 x 9.61 x 3.82 (in)
Dimensions: 381 x 244 x 97 (mm)
Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B
Warranty: 2 Year Limited
Applications:
Automotive
Recreational vehicles
Marine
Communications sites
Battery back-up systems
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
632.32 |
|
|
MKR-28 Trolling Motor Plug & Receptacle
The MKR-28 trolling Motor Plug and Receptacle provides continuous power and are rated to 60 amps up to 48V. Designed for freshwater and saltwater applications, silver-plated terminals provide reliable use in the harshest conditions. This plug is the recommended replacement for the MKR-18 Plug & Receptacle (part number 1865102) and MKR-26 (part number 1865128). Package includes: trolling motor plug with 18” wire lead, receptacle with 24” wire lead, mounting faceplate, dust cap, 1-10 AWG splicer, 1 AWG ferrule, 2 AWG ferrule, 4 AWG ferrule, heat shrink, hex wrench, and installation manual.
Features:
Trolling Motor Plug and Receptacle provide continuous power rated to 60 amps up to 48V
Designed for freshwater and saltwater applications
Silver-plated terminals for a reliable corrosion-resistant connection in any freshwater or saltwater application
Sealed waterproof design
Secure threaded electrical connection
Adjustable mounting orientations
Continuous power rated to 60 amps up to 48V
8 AWG wire leads
Compatible with 1 - 10 AWG wire sizes
|
130.75 |
|