|
3 Blade stainless interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.
|
497.99 |
|
|
Teak Flag Pole - 1" x 24"
Boaters appreciate teak's traditional beauty because of its intricate grain patterns and color variations. The high oil content of the wood keeps it from deteriorating or warping in the harsh marine environment of sun, wind, and water. Teak's natural oils and Silica (sand) make it impervious to insects and wood rot. To maintain the lasting beauty of teak, it should be cleaned using a good teak cleaner and oiled periodically with a quality teak oil.
Features:
Made from the finest grade A, kiln-dried teakwood
No deteriorating or warping
|
22.19 |
|
|
Ampco Fluid End Aluminum Bronze Full Impeller for KC2 1 X 3/4
|
1758.24 |
|
|
3 and 4 Blade stainless propeller for Suzuki. Front propeller is 25 tooth spline. Rear Propeller is 15 tooth spline and thru hub exhaust. Pairing front and rear SG propellers with the same pitch is strongly recommended.
|
549.99 |
|
|
3 and 4 Blade stainless propeller for Suzuki. Front propeller is 25 tooth spline. Rear Propeller is 15 tooth spline and thru hub exhaust. Pairing front and rear SG propellers with the same pitch is strongly recommended.
|
579.99 |
|
|
4 Blade stainless interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.
|
499.99 |
|
|
4 Blade stainless interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.
|
499.99 |
|
|
3 Blade stainless propeller for Mercury 90+ horsepower outboard engines, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower engines. All with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.
|
496.99 |
|
|
3 Blade stainless propeller for 90 - 300 horsepower engines with 15 tooth spline and thru hub exhaust. 4-3/4" Gear case.
|
496.99 |
|
|
XKA Stainless Steel Trim Tab - 9 x 24
The Lectrotab stainless steel trim tab design provides unmatched strength and reliability. All stainless steel tabs are fabricated with a continuous rolled and pinned hinge. This design eliminates the need for welding.
Combined with a precision-engineered actuator, this kit is built to combine quiet operation with a non-hydraulic, maintenance free design. The unit is corrosion free, ensures very accurate tab positioning, provides maximum lift force, and is totally self-contained for easy installation. The actuator assembly is packaged in a non-metallic permanently sealed housing. No components need to be installed inside the boat.
Most importantly, unlike hydraulic trim tabs, there is no oil to leak out. The actuator incorporates either a standard or low profile transom mounting bracket.
*Control switch not included
Features:
Continuous rolled and pinned hinge provides added strength and eliminates the need for welding
Upper ram seal location cannot be damaged due to fouled ram or barnacle growth
Utilizes internal pressure equalization system
Internal brake system prevents unwanted tab movement when under way or backing down
Quiet operation
Actuators are fully load tested to push 1000 lbs of force
Non-metallic external structure which cannot corrode and will not deteriorate in the sun or under water
Technical Specifications:
Trim Tab Size (L x W) - 9" x 24" (23 x 61 cm)
Boat Length - 24' to 37' (7 to 11 M)
Trim Tab Material - 12 gauge, 304 Stainless Steel
Actuator DC Voltage - 12 V
Actuator Stroke Length - 2.25" (57 mm)
Actuator Cable Length - 23' (7 M)
Actuator Vertical Height - 11.875" (302 mm)
In the Box:
Two (2) Stainless Steel tabs
Two (2) actuators w/23' (7 M) cables
Instruction Manual
*Sold as an Individual
|
1016.82 |
|
|
XKA Stainless Steel Trim Tab - 12 x 24
The Lectrotab stainless steel trim tab design provides unmatched strength and reliability. All stainless steel tabs are fabricated with a continuous rolled and pinned hinge. This design eliminates the need for welding.
Combined with a precision-engineered actuator, this kit is built to combine quiet operation with a non-hydraulic, maintenance free design. The unit is corrosion free, ensures very accurate tab positioning, provides maximum lift force, and is totally self-contained for easy installation. The actuator assembly is packaged in a non-metallic permanently sealed housing. No components need to be installed inside the boat.
Most importantly, unlike hydraulic trim tabs, there is no oil to leak out. The actuator incorporates either a standard or low profile transom mounting bracket.
*Control switch not included
Features:
Continuous rolled and pinned hinge provides added strength and eliminates the need for welding
Upper ram seal location cannot be damaged due to fouled ram or barnacle growth
Utilizes internal pressure equalization system
Internal brake system prevents unwanted tab movement when under way or backing down
Quiet operation
Actuators are fully load tested to push 1000 lbs of force
Non-metallic external structure which cannot corrode and will not deteriorate in the sun or under water
Technical Specifications:
Trim Tab Size (L x W) - 12" x 24" (30 x 61 cm)
Boat Length - 28' to 48' (8.5 to 14.5 M)
Trim Tab Material - 12 gauge, 304 Stainless Steel
Actuator DC Voltage - 12 V
Actuator Stroke Length - 2.25" (57 mm)
Actuator Cable Length - 23' (7 M)
Actuator Vertical Height - 11.875" (302 mm)
In the Box:
Two (2) Stainless Steel tabs
Two (2) actuators w/23' (7 M) cables
Instruction Manual
*Sold as an Individual
|
1468.37 |
|
|
3 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.
|
179.99 |
|
|
3 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.
|
179.99 |
|
|
3 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.
|
179.99 |
|
|
3 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.
|
167.99 |
|