|
3 Blade stainless propeller for DF 150, 175, 200, 225, 250, 300 with 15 tooth spline and thru hub exhaust. 4-3/4" Gear Case.
|
506.99 |
|
|
16-14 AWG to 22-18 AWG Vinyl Step Down Butt Connector - 25-Pack
Ancor's Marine Grade terminals differ from automotive terminals by being designed for the harsh marine environment.
Features:
Vinyl Insulated
UL 486C
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
18.56 |
|
|
16-14 AWG to 22-18 AWG Vinyl Step Down Butt Connector - 100-Pack
Ancor's Marine Grade terminals differ from automotive terminals by being designed for the harsh marine environment.
Features:
Vinyl Insulated
UL 486C
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
37.96 |
|
|
3 Blade high performance aluminum interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.
|
115.99 |
|
|
3 Blade stainless interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.
|
435.99 |
|
|
3 Blade stainless propeller for Mercury 90+ horsepower outboard engines, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower engines. All with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.
|
496.99 |
|
|
3 and 4 Blade stainless propeller for Suzuki. Front propeller is 25 tooth spline. Rear Propeller is 15 tooth spline and thru hub exhaust. Pairing front and rear SG propellers with the same pitch is strongly recommended.
|
579.99 |
|
|
Manufactured from high-density polyethylene with UV inhibitors. Meets low permeation standards to satisfy EPA/CARB regulations, USCG and ABYC standards. Seamless one-piece construction with reserve fuel area designed into tank by means of a partitioned bottom. When gauge registers empty, simply tilt the tank to access reserve fuel supply. Features 90° fuel withdrawal assembly that rotates 360° to reduce fuel line kinks. Direct sight fuel gauge with glass lens, 2-stage self-venting fuel cap required by EPA/CARB.
|
147.99 |
|
|
G-4 Twin Eye Fender 6.5" x 22" - Graphite
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes, and reinforced rope holds for long-term durability.
The G Series fender is designed to provide protection and stand-off for vessels between 10 to 40 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Hangs vertically or horizontally
Unique Polyform valve for years of service
Technical Specifications:
Size (diameter x length) - 6.5" x 22" (16.5 x 55.9 cm)
Eye Diameter - 0.75" (1.9 cm)
Circumference - 20.4" (51.9 cm)
Volume - 2.2 gallons (8.3 L)
Boat Size - 20' - 25' (6.1 - 7.6 M)
Weight - 2.6 lb
*Sold as an Individual
|
34.45 |
|
|
9" x 18" Standard Mount Trim Tab Kit without Switch Kit- 12V
Lenco Electric Standard Mount Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ballscrew design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics.
Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Trim Tab blades are 12 Gauge - 304 SS with a 5/8" flared trailing edge and 1/8" diameter hinge pin. Kits include standard actuators with 5/16" SS bolts.
Kit Contents:
2 each of 12-gauge stainless steel trim tab blades
2 each of #15054-001 actuator with 6' leads and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (116) upper mounting brackets with gland seal
2 each of #50014-001 (119) lower mounting brackets
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 22' to 30'
Length of Tab: 9"
Width of Tab: 18"
Hinge Height: 2"
Minimum Transom Height: 14"
Blades: 12 Gauge Stainless Steel
Finish: Smooth
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
620.03 |
|
|
9 M SIDB Y - 9-Pin Side Imaging Dual Beam Splitter Cable
Y Cable - Side Imaging and Dual Beam - allows you to use two transducers on one unit without the use of a transducer switch.
For use with Side Imaging products only, in conjunction with a dual beam transducer only. For improved high speed performance for bottom tracking.
30" length.
Supports MEGA Side Imaging.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
40.00 |
|
|
MAGNUS Escape Hatch - OD 22-3/16" x 22-3/16"
Heavy Duty Ocean Hatch
MAGNUS is a complete range of extra heavy-duty hatches. They are CE-classified AI, which means to say that they are designed for ocean use and can be fitted in any part of the hull or deck.
These hatches are provided with friction hinges, which will keep the hatch open in any position, without the need for stays. The hatch can be opened through 180° and there are virtually no obstructions in the hatch opening. Like other VETUS hatches, the MAGNUS range can be opened from inside or outside the boat. They can also be left locked; either completely watertight or in a ventilation position.
The frame profile is hand-polished and anodized. The acrylic has a thickness of 10 mm and the color is “dark smoke”.
The build-in dimensions (the cut-out sizes) of the Magnus hatches are in conformity which those that are current in the market.
Features:
External Dimensions - 22 3/16" x 22 3/16"
Cut Out Dimensions - 19 15/16" x 19 15/16"
Number of Handles - 4
*VETUS strongly advises against using MAGNUS hatches as an A1 escape hatch in the underside of a multihull. Due to the flexible nature of these types of vessels, water tightness cannot be guaranteed unless the hatch is installed on a flat and inflexible structure.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
596.88 |
|
|
Jabsco X4020-122A O'Ring 1.6 X 22.1 Nitrile
|
6.16 |
|
|
HTM-1 - 5-1/2" x 22" - Double Layer -Black
Double layer means softer, more durable & reversible.
Master Fender Covers are specially designed to protect the topsides and hull from fender scuff and reduce the need for expensive gel coat repairs.
They are made from a premium stain resistant, non-abrasive, loop-knit acrylic fabric, which is both durable and fade resistant. They are available in a variety of colors and sizes to suit your individual requirements.
|
11.99 |
|
|
Super Gard™ 6.5" x 22" Inflatable Vinyl Fender - White
Taylor Made Products has incorporated the latest in technology, design innovation, and attention to detail to bring you the finest looking, top performing protection for your dollar. Super Gard™ fenders are in a class of their own. Made from the highest quality marine grade vinyl, Super Gards™ feature a HIGH GLOSS finish and double molded black ends for extra strength where you need it the most. Seamless one-piece construction with ribbed sides minimizes roll, and a molded-in valve ensures easy inflation and long life.
Boat Size: 20' to 25'
Recommended inflation is 2 psi.
* The most accurate way to select the right fender for your boat is to survey your docking area to find out what fender is in use for the same size and weight of boat, in terms of fender dimensions and quantities, and use that as a guideline.
Lifetime Warranty against splitting or bursting
|
44.45 |
|