RAM® Printer Cradle for Brother PocketJet 7 Series, 6/6 Plus & 673 The RAM-VPR-101 is designed to hold Brother® PocketJet® Series portable printers. A custom-fit enclosure, the cradle is form-fitting with no sharp edges and adds little to the overall size of the printer. Key features are a full view of LEDs, a sight hole to check the paper level, and a caddy to store pens, cell phones, paper clips, glasses, and other useful items. Complete kits are available as stand-alone systems or integrate with your existing RAM products. Features: The form-fit cradle is specifically designed to hold Brother PocketJet 7 series, 6, 6 Plus, and 673 portable printers Compatible with RAM® round ball bases for attaching a double socket arm; ball and socket technology allows for near-infinite adjustability Made of high-strength composites for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: (4) #8-32 x 5/8" Machine Screws & (4) #8-32 Nylock Nuts  Hole Pattern: 4-Hole AMPS: 1.181" x 1.496"  Materials: High Strength Composite Weight: 1.1lbs

RMX4500-01 RailMount Pre-Cut for Garmin echoMAP™ 7" Series Garmin echoMAP™ Models: 72SV 73SV 74SV 75SV 72DV 73DV 74DV 75DV RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. Our Commitment to Quality We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.

RAM Tab-Tite Universal Clamping Cradle f/Google Nexus 7 w/ or w/o Light Duty Sleeve The RAM-HOL-TAB18U consists of a spring loaded back plate and custom support cups for the Google Nexus 7 WITH OR WITHOUT LIGHT DUTY SLEEVE. The spring loaded design makes it easy to load and unload your tablet, along with keeping it secure while on the go. Interchangeable cup ends are designed to optimize the functionality of your tablet, allowing access to audio jacks, usb, power, and other ports, your tablet can be used just as it was intended. Perfect for stationary or on the go applications, the RAM-HOL-TAB18U is just what you need to get the most out of your tablet. The RAM Tab-Tite cradle is compatible with the following tablets: Google Nexus 7 WITH OR WITHOUT LIGHT DUTY SLEEVE The Tab-Tite cradle is compatible with any tablet or reader that will fit the dimensions listed below. It is important to verify the dimensions of your tablet when determining the overall size. Tab-Tite Cradle Dimensions: Height: 7" minimum to 8.875" maximum Width: maximum to 4.7" Depth: maximum to 0.43" Tab-Tite Cradle Features: 1. Support cups contain open slots to accommodate for tablets of various sizes 2. Back plate can support various size support cups 3. Spring loaded tension provides secure support for your tablet 4. Spring loaded cradle allows for quick release of your tablet 5. High strength materials maximize longevity of cradle 6. Full access to all ports 7. Lifetime warranty Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag. The cradle includes a set of two nuts and bolts to connect the cradle to any of the RAM compatible mounts. RAM cradles do not include the RAM-B-238U (Diamond Base & Ball) or RAP-B-238U (Diamond Composite Base & Ball), required to attach to the cradle and RAM mounting system.

RAM® Form-Fit Holder for iPhone 13 Pro Max, 14 Plus & Pro Max with Ball  This form-fit cradle was designed specifically for the Apple iPhone 13 Pro Max, 14 Plus, and 14 Pro Max. Designed for phones without cases, this cradle features one-handed docking and removal of your iPhone, and all buttons, cameras, ports, and speakers remain exposed and accessible. This holder includes a B size RAM® diamond ball base to attach a double socket arm – compatible with a wide range of additional RAM® components. Features: Form-fit cradle for Apple iPhone 13 Pro Max, 14 Plus, & 14 Pro Max provides a perfect fit for your device without a case; B size diamond ball adapter included Includes B size RAM® diamond ball base for attaching a double socket arm; ball and socket technology allows for near-infinite adjustability Made of high-strength composites for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: Assembly Hardware Ball Size: B Size (1") Weight Capacity: Standard Use: 2 lbs/Heavy-Duty Use: 1 lb  Materials: Marine-grade aluminum/High strength composite Weight: 0.2 lbs Packaging Type: Poly Bag Additional Information: Exposure to vibrations, like those generated by high-powered motorcycle engines, might impact iPhone cameras.

RAM® Form-Fit Cradle for Garmin GPSMAP® 176, 196, 276C, 396, 496 & More The RAM-HOL-GA7U consists of a high-strength composite cradle and hole pattern that will allow attachment to all RAM components or mounts that contain the universal AMP hole pattern. Compatible and interchangeable with a wide range of popular RAM mounting products, this cradle is ready to complement a GPS and become the most useful accessory in a vehicle.  Features: A set of two nuts and bolts to connect the cradle to any RAM components or mounts that contain the universal AMP hole pattern Specifications: Hardware Included: (2) #8-32 x 1/2" Machine Screws, (2) #8-32 x 5/8" Machine Screws, (2) #8-32 x 3/4" Machine Screws, and (2) #8-32 Nylock Nuts Hole Pattern (inch): 2-Hole AMPS: 1.912" Materials: High-strength composite Packaging Type: Polybag Weight: 0.14 lb. Compatibility: Garmin: GPSMAP 176, GPSMAP 176C, GPSMAP 196, GPSMAP 276C, GPSMAP 296, GPSMAP 376C, GPSMAP 378, GPSMAP 396, GPSMAP 478, and GPSMAP 496

RAM® Form-Fit Cradle for Apple iPhone 11 This high-strength composite, form-fit cradle was designed specifically for the Apple iPhone 11. Allowing for easy one-handed docking and removal of your iPhone 11, all buttons, cameras, ports, and speakers remain exposed and accessible. The 2-hole AMPS pattern on the back of the cradle and included hardware allows for the attachment of a RAM® diamond ball base – compatible with a wide range of additional RAM® components. Features: Form-fit cradle for iPhone 11 provides a perfect fit for your device without a case Compatible with B and C size RAM® diamond ball bases for attaching a double socket arm; ball and socket technology allows for near-infinite adjustability Made of high-strength composites for durability and reliability in the most demanding environments Backed by a lifetime warranty Material: High strength composite Hole Pattern: 2-Hole AMPS: 1.912"  Hardware Included: (2) #8-32 x 1/2" Machine Screws (2) #8-32 x 5/8" Machine Screws (2) #8-32 x 3/4" Machine Screws (2) #8-32 Nylock Nuts

RAM® Form-Fit Cradle for Apple iPhone 11 Pro This high-strength composite, form-fit cradle was designed specifically for the Apple iPhone 11 Pro. Allowing for easy one-handed docking and removal of your iPhone 11 Pro, all buttons, cameras, ports, and speakers remain exposed and accessible. The 2-hole AMPS pattern on the back of the cradle and included hardware allows for the attachment of a RAM® diamond ball base – compatible with a wide range of additional RAM® components. Features: Form-fit cradle for iPhone 11 Pro provides a perfect fit for your device without a case Compatible with B and C size RAM® diamond ball bases for attaching a double socket arm; ball and socket technology allows for near-infinite adjustability Made of high-strength composites for durability and reliability in the most demanding environments Backed by a lifetime warranty Hole Pattern: 2-Hole AMPS: 1.912" Hardware Included:  (2) #8-32 x 1/2" Machine Screws (2) #8-32 x 5/8" Machine Screws (2) #8-32 x 3/4" Machine Screws (2) #8-32 Nylock Nuts

Locking EZ-ROLL'R™ Cradle for the Garmin nuviCam and dezlCam The Garmin nuviCam™ & dezlCam™ keeps an extra eye on the road. And RAM Mounts custom cradle for these innovative devices keeps traffic information in your line of sight and keeps the device secure in your vehicle. The cradle allows for full range of motion of the device camera and integrates the factory Garmin magnetic dock for access to charging. The high-strength composite mount integrates a cable retention system to prevent accidental unplugging. The custom-fit cradle also has a locking option that is installed using press-fit nuts to enhance security. The cradle has two location options to attach the RAM ball (comes with 1" B-Size ball). Compatible Devices: Garmin nuviCam™ LMTHD Garmin dezlCam™ LMTHD Features: Open access to all electronic ports including speaker, microphone, SD and mUSB slots Allows for full range of motion for the camera Roller design for super smooth placement and removal of the GPS High strength materials ensure product longevity Form fitted cradle supports and protects device without vibration Cradle integrates the factory Garmin magnetic dock Comes with B sized, 1" ball Locking attachment allows for a low profile theft deterrent Lifetime warranty Made in the U.S.A Material: High Strength Composite

Locking Case for the Garmin dezl™760LMT, nuvi® 2797LMT & RV 760LMT The RAM-HOL-GA61LU consists of a high strength composite locking case and hole pattern that will allow the attachment to all RAM components or mounts that contain the universal AMPs hole pattern. Compatible and interchangeable with a wide range of popular RAM Mounting products, this locking case is ready to compliment your GPS and become the most useful accessory in your vehicle. Included is a set of two nuts and bolts to connect the cradle to any RAM components or mounts that contain the universal AMPs hole pattern. Locking Case Features: 1. Open access to all electronic ports including audio port, speaker/mic and mini USB 2. Custom pocket for factory dock 3. Rugged construction deters theft and protects vulnerable areas of device 4. Secures at 4 corners with provided hardware 5. Will not obstruct GPS signal 6. Secure USB power connection with wire retention 7. Lifetime warranty 8. Made in the U.S.A. Specifications: Material: High Strength Composite Note: *The RAM-HOL-GA61LU was designed prior to the BC20 wireless backup dock was released. The current design will not allow for that dock module to be integrated into the cradle. The "U" in the part number reflects product packaged in poly bag. Weight: 0.45 lbs. Special Information: Designed for use with third party EOBR equipment and recording hours of service in compliance with CSA (compliance, safety, accountability) initiative. To learn more visit the Federal Motor Carrier Safety Administration (FMCSA) website. For more information about Garmin Commercial Solutions and PND-based Mobile Resource Management (MRM) Solutions, visit the Garmin website.

RAM Handle Wrench for "D" Size Ball Arms & Mounts The RAM handle wrench is designed to be used with the knob found on "D" size ball arms and mounts. The wrench matches the shape of the knob found on the side of "D" arms, and lets you give the arm an extra tight grip. This wrench was originally made for the military when using the RAM mounts in cold weather, and the knob could not be tightened by hand. Material: Powder Coated Marine Grade Aluminum Ball Size: 2.25" Rubber "D" Ball Size Note: The "U" in the part number reflects product packaged in poly bag.

PedestalPod with RAM Mount Pre-Cut for Lowrance HDS-9 Gen2 Touch, HDS-9 Gen3 & HDS Carbon 9 - Carbon Black PedestalPod with RAM Mounts is specifically designed for mounting the fishfinder near the bow on Bass Boats. Built on the foundation of NavPods popular range of waterproof housings for marine electronics, PedestalPods position your fishfinder/chartplotter at an easy to reach 20” off the deck. This allows the user easy access to the display for changes to range, zoom or even control the trolling motor. There is a big difference between reaching down to a height off the deck of 20” to control your fishfinder compared to reaching all the way down to the deck when it was only bracket mounted.  PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal. This offers protection of your fishfinder/chartplotter from the harshest of wet boating conditions.  This protection assures reliability and longevity of your marine electronics. PedestalPod with RAM Mounts utilizes the proven RAM Mounting system with the large 2.25” rubber “D” size ball and the RAM pin-lock security solution.  RAM Mounts are designed with a patented rubber ball and socket system that allows an almost infinite amount of ways to position the angle of the fishfinder for that precise position of viewing. When you might be trailering, or storing the boat, the display can fold flat onto the deck with only 10” of clearance.  This will allow most boat covers to fit over the PedestalPod when not in use. Your fishfinder is easily flush mounted into the pre-cut face of the NavPod. There are pre-cut models available for 7”, 9” and 12” LCD displays from all major marine electronic manufacturers. PedestalPods are waterproof housings for marine electronics specifically designed for bass boats. PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your marine electronics from the harshest of wet boating conditions. PedestalPods provide the convenience of height for accessibility and added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20” off the deck and located near the bow and at a 45-degree angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. All NavPods are manufactured with a double gasket system that provides an excellent watertight seal. They keep harsh spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the PedestalPod. The heavy duty, black powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look. It provides protection for wires and connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. All NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. PedestalPods are available pre-cut for 7”, 9” and 12” LCD displays from all major marine electronic manufacturers. Constructed out of durable ABS like all Gen3 NavPods, black carbon PedestalPods have the same high gloss finish with UV stability. NavPod backs up their commitment to quality by offering a 10-year warranty on all Gen3 NavPods. PedestalPods – Protection, Convenience, Security

PedestalPod with RAM Mount Pre-Cut for Lowrance HDS-9 MFD Gen2 Touch & HDS-9 Gen3 - Carbon Black PedestalPod with RAM Mounts is specifically designed for mounting the fishfinder near the bow on Bass Boats.  Built on the foundation of NavPods popular range of waterproof housings for marine electronics, PedestalPods position your fishfinder/chartplotter at an easy-to-reach 20” off the deck. This allows the user easy access to the display for changes to range, zoom or even control the trolling motor. There is a big difference between reaching down to a height off the deck of 20” to control your fishfinder compared to reaching all the way down to the deck when it was only bracket mounted. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal. This offers protection of your fishfinder/chartplotter from the harshest of wet boating conditions.  This protection assures the reliability and longevity of your marine electronics. The PedestalPod with RAM Mounts utilizes the proven RAM Mounting system with the large 2.25” rubber “D” size ball and the RAM pin-lock security solution. RAM Mounts are designed with a patented rubber ball and socket system that allows an almost infinite amount of ways to position the angle of the fishfinder for that precise position of viewing. When you might be trailering, or storing the boat, the display can fold flat onto the deck with only 10” of clearance.  This will allow most boat covers to fit over the PedestalPod when not in use. Your fishfinder is easily flush mounted into the pre-cut face of the NavPod. There are pre-cut models available for 7”, 9”, and 12” LCD displays from all major marine electronic manufacturers. PedestalPods – Protection, Convenience, Security.

GP1500-04 SystemPod Pre-Cut for Humminbird HELIX 7 Series GP1500 Series for 9.5" Guard, SystemPods for Sail are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic. A SystemPod is best mounted on a Single Bend AngleGuard. The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. We have re-designed and re-tooled all of the popular NavPods. We have reviewed all of the former products and selected the best design elements of each and incorporated them in every new Gen3 product. Our Commitment to Quality We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.

GM H7 Gimbal Mount for Select HELIX 7 Series The GM H7 is a plastic gimbal mount for all HELIX 7 models products except HELIX 7 G4N models . This includes the gimbal mount, knobs and mounting hardware. Compatible Devices: All HELIX 7 models, except HELIX 7 G4N models WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Tuthill 2LE-A-7 Pump 6.2Gpm 1/2"Ports Cast Iron Rotary Gear Pump Pump End Only L Series Pump Cast Iron Construction Tang Shaft Inlet Port is 1/2 inch NPT Discharge Port is 1/2 inch NPT Positive Displacement, Internal Rotary Gear Design Open Flow at 1800 RPM : 5.6 GPM at 1800 RPM Standard Discharge Pressure: up to 500 PSI Inlet Pressure: up to 280 PSI Maximum Differential Pressure: 300 PSI Temperature: up to 375 F Typical Viscosity Range: 40 to 1000 SSU