VANL1 ANL Fuse Holder - 1/0 to 4 AWG It can be tough to find a good place for your system's fuse holder in a crowded engine compartment.  T-SPEC helps you out with their extremely compact ANL fuse holder for 1/0-gauge wire that can fit almost anywhere. Black nickel-plated brass construction ensures excellent current flow, while a polycarbonate cover protects the fuse against impacts and dirt.  Features: Compact fuse holder Accepts an ANL fuse (not included) Connects to 1/0 to 4 gauge power wire Black nickel-plated brass  Anodized finish resists rust Impact-resistant polycarbonate cover Fuse fastening screws can be used with a variety of tools TPE wrapped soft touch Dual sizes gasket set Water resistant In the Box: ANL fuse holder Plastic cover 2 Rubber grommets (pre-installed) *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VANL ANL Fuse Holder - 1/0 to 4 AWG It can be tough to find a good place for your system's fuse holder in a crowded engine compartment.  T-SPEC helps you out with their extremely compact Series rotating ANL fuse holder for 1/0-gauge wire that can fit almost anywhere.  Black nickel-plated brass construction ensures excellent current flow, while a polycarbonate cover protects the fuse against impacts and dirt.  Features: Compact fuse holder with 360° rotating base Accepts an ANL fuse (not included) Connects to 1/0 to 4 gauge power wire Black nickel-plated brass construction  Anodized finish resists rust Impact-resistant polycarbonate cover Fastening screws can be used with a variety of tools In the Box: V12-series ANL fuse holder Plastic cover 2 Rubber grommets (pre-installed) Installation sheet *Sold as an Individual  WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VMANL1 Mini-ANL Fuse Holder - 1/0 to 4 AWG T-SPEC'S VMANL 1fuse holder ensures excellent current flow by using sturdy, lock-down fasteners to secure your power cable, so you don't have to worry about it getting loose over time.  Combine this with solid brass construction and water resistance, and you've got a great link between your amp and your battery that will protect your electrical system. The T-SPEC VMANL1 fuse holder accepts 1/0 to 4 gauge power cables and mini-ANL fuses. Features: Compact fuse holder  Accepts mini-ANL fuses Connects to 1/0 to 8 gauge power cable Black nickel finish Water resistant T20 Torx® screws Gate Lock technology In the Box: One (1) mini-ANL fuse holder Two (2) Threaded end-caps 1/0 and 4 gauge rubber grommets (pre-installed) *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VDMANL DUAL Mini-ANL Fuse Holder - 1/0 to 4/8 AWG T-SPEC'S VDMANL Dual fuse holder ensures excellent current flow by using sturdy, lock-down fasteners to secure your power cable, so you don't have to worry about it getting loose over time.  Combine this with solid brass construction and water resistance, and you've got a great link between your amp and your battery that will protect your electrical system. The T-SPEC VDMANL Dual fuse holder accepts 1/0 to 4/8 gauge power cables and mini-ANL fuses. Features: Accepts mini-ANL fuses Connects to 1/0 to 4/8 gauge power cable Solid brass construction  Impact resistant polycarbonate cover Black nickel finish Water resistant T20 Torx® screws Gate Lock technology In the Box: One (1) mini-ANL fuse holder Two (2) Threaded end-caps 1/0 and 4 /8 gauge rubber grommets (pre-installed) *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VMANL Mini-ANL Fuse Holder - 4 to 8 AWG T-SPEC'S VMANL fuse holder ensures excellent current flow by using sturdy, lock-down fasteners to secure your power cable, so you don't have to worry about it getting loose over time.  Combine this with solid brass construction and water resistance, and you've got a great link between your amp and your battery that will protect your electrical system. The T-SPEC VMANL fuse holder accepts 4 to 8 gauge power cables and mini-ANL fuses. Features: Compact fuse holder with 360° rotating base Accepts mini-ANL fuses Connects to 4- to 8-gauge power cable Solid brass construction  Black nickel finish Water resistant T20 Torx® screws Gate Lock technology In the Box: One (1) mini-ANL fuse holder Two (2) Threaded end-caps 4 and 8 gauge rubber grommets (pre-installed) *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VFDB2 MANL 2 Position Distribution Block with Cover This compact distribution block from T-Spec will handle the high-current power distribution for your single source to two (2) smaller gauge power wires, ensuring that your wiring's connected securely, looking neat, and safely fused.   T-spec's Universal Screw Design for securing the wires and mini ANL fuses to the block works with a variety of tools.   Solid black nickel-plated brass construction ensures reliable power flow, and an impact-resistant polycarbonate cover keeps the fuses and connections clean.   Fuses sold separately.  Features: One (1) 1/0 to 4 AWG in to two (2) 4/8 AWG out TPE wrapped soft touch Dual sizes gasket set Water-resistant Solid brass construction Black nickel finish T20 Torx® screws Gate Lock technology In the Box: One distribution block for mini-ANL fuses with one (1) 4 or 1/0 AWG set-screw input and two (2) 4/8 AWG set-screw outputs Plastic cover (attached) 3 Rubber grommets and sleeves (pre-installed) *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VFDB4 MANL 4 Position Distribution Block with Cover This compact distribution block from T-Spec will handle the high-current power distribution for your single source to four (4) smaller gauge power wires, ensuring that your wiring's connected securely, looking neat, and safely fused.   T-spec's Universal Screw Design for securing the wires and mini ANL fuses to the block works with a variety of tools.   Solid black nickel-plated brass construction ensures reliable power flow, and an impact-resistant polycarbonate cover keeps the fuses and connections clean.   Fuses sold separately.  Features: One (1) 1/0 to 4 AWG into four (4) 4/8 AWG out TPE wrapped soft touch Dual sizes gasket set Water-resistant Solid brass construction Black nickel finish T20 Torx® screws Gate Lock technology In the Box: One distribution block for mini-ANL fuses with one (1)  4 or 1/0 AWG set-screw input and four (4) 4/8 AWG set-screw outputs Plastic cover (attached) 3 Rubber grommets and sleeves (pre-installed) *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VPNB4 MANL 4 Position All-In-One Distribution Block with Cover T-Spec designed VPNB4 distribution block to handle the high-current power and ground distribution for four (4) power sources, and protect them each with a mini-ANL fuse.  This hefty little block distributes power from one (1) 1/0-gauge positive power cable to four (4) 4 to 8 gauge power leads, each routed through a mini-ANL fuse.  Then, the same block receives the amps' two ground wires and combines them for a single 1/0 to 4 gauge ground cable. Fuses sold separately.  Features: (2 positive) 1/0 to 4 AWG in to (4 positives) 4/8 AWG out (1 negative) 1/0 to 4 AWG in to (4 negatives) 4/8 AWG out TPE wrapped soft touch Dual sizes gasket set Water-resistant Solid brass construction Black nickel finish T20 Torx® screws Gate Lock technology In the Box: Distribution block for both power and ground Plastic cover (attached) 3 Rubber grommets and sleeves on power inputs (installed) 2 Rubber grommets and sleeves on power outputs (installed) *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VPNB2 MANL 2 Position All-In-One Distribution Block with Cover T-Spec designed VPNB2 distribution block to handle the high-current power and ground distribution for two (2) power sources, and protect them each with a mini-ANL fuse.  This hefty little block distributes power from one (1) 1/0-gauge positive power cable to two (2) 4- to 8-gauge power leads, each routed through a mini-ANL fuse.  Then, the same block receives the amps' two ground wires and combines them for a single 1/0-gauge ground cable. Fuses sold separately.  Features: (2 positive) 1/0 to 4 AWG in to (2 positives) 4/8 AWG out (1 negative) 1/0 to 4 AWG in to (2 negatives) 4/8 AWG out TPE wrapped soft touch Dual sizes gasket set Water-resistant Solid brass construction Black nickel finish T20 Torx® screws Gate Lock technology In the Box: Distribution block for both power and ground Plastic cover (attached) 2 Rubber grommets and sleeves on power inputs (installed) 2 Rubber grommets and sleeves on power outputs (installed) *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VAGU AGU Fuse Holder 4 to 8 AWG Fusing an aftermarket stereo system provides protection for your car and your car stereo.  No fuse system provides better protection than T-Spec.  The new T-Spec compact brass designs are constructed from solid brass and are smaller than anything else in the industry.  This combination of top quality materials and thoughtful design provides an incredibly reliable and simple to install product that will last for years.  Features: Compact fuse holder with 360° rotating base Accepts an AGU fuse (not included) Connects to 4 to 8 gauge power wire Black nickel-plated brass construction  Anodized finish resists rust Impact-resistant polycarbonate cover Fastening screws can be used with a variety of tools T20 Torx® screws Gate Lock technology In the Box: AGU fuse holder Plastic cover 2 Rubber grommets (pre-installed) Installation sheet *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VDB2 2-Position Distribution Block with Cover T-Spec designed their VDB2 distribution block to handle the high-current power distribution for two (2) power sources while keeping your wiring connected securely and looking neat.   You can also use this hefty little block to combine the ground wires of two (2) sources to a single grounding point.  Solid black nickel-plated brass construction ensures reliable power flow, and an impact-resistant polycarbonate cover protects your connections from the weather. Features: One (1) 1/0 to 4 AWG into two (2) 4/8 AWG out TPE wrapped soft touch Dual sizes gasket set Water-resistant Solid brass construction Black nickel finish T20 Torx® screws Gate lock technology In the Box: Distribution block with one (1) 1/0 set-screw input and two (2) 4 or 8 AWG set-screw outputs Plastic cover (attached) 3 Rubber grommets and sleeves (pre-installed on input and outputs) Two 1/2" screws *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

VDB4 4-Position Distribution Block with Cover T-Spec designed their VDB4 distribution block to handle the high-current power distribution for four (4) power sources while keeping your wiring connected securely and looking neat.   You can also use this hefty little block to combine the ground wires of four (4) sources to a single grounding point.  Solid black nickel-plated brass construction ensures reliable power flow, and an impact-resistant polycarbonate cover protects your connections from the weather.  Features: One (1) 1/0 to 4 AWG into four (4) 4/8 AWG out TPE wrapped soft touch Dual sizes gasket set Water-resistant Solid brass construction Black nickel finish T20 Torx® screws Gate lock technology In the Box: Distribution block with one (1) 1/0 set-screw input and four (4) 4 or 8 AWG set-screw outputs Plastic cover (attached) 3 Rubber grommets and sleeves (pre-installed on input and outputs) Two 1/2" screws *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ANL Fuse Holder with 2 Additional Studs, 750A Providing high-capacity fusing, fast response and very high interrupt ratings (ANL up to 6,000 Amps, Class-T up to 20,000 Amps), these fuse holders are ideal for protecting today's demanding onboard power electronics technology including inverters and battery chargers. They also protect wiring from short circuits. Pro Installer fuse holders' durable construction allow fuses to run at maximum load. Radiused ends improve cable routing options ANL: for use with 5/16" (8mm) or 3/8" (10mm) ANL fuses WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

V12-CBF200 Circuit Breaker - 200 AMP Getting tired of replacing your power fuse every time you show off how loud your system can play?  You should consider replacing the fuse holder with a circuit breaker.  T-Spec's competition-grade circuit breaker protects your wiring and battery with reliable, fast-acting, spring-loaded disconnection when sensing a short circuit or over-current condition. This breaker accepts 1/0- to 4-gauge wire and features 24-karat gold-plated conductors for corrosion-free connections.  You'll need Allen head wrenches to install this circuit breaker. Features: 1/0 or 4 AWG In/Out  Manual reset button  24K hard gold plated Resistant to corrosion  In the Box: 200A Circuit breaker with 1/0 AWG or 4 AWG input and output Instruction sheet *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

V12-CBF100 Circuit Breaker - 100 AMP Getting tired of replacing your power fuse every time you show off how loud your system can play?  You should consider replacing the fuse holder with a circuit breaker.  T-Spec's competition-grade circuit breaker protects your wiring and battery with reliable, fast-acting, spring-loaded disconnection when sensing a short circuit or over-current condition. This breaker accepts 1/0- to 4-gauge wire and features 24-karat gold-plated conductors for corrosion-free connections.  You'll need Allen head wrenches to install this circuit breaker. Features: 1/0 or 4 AWG In/Out  Manual reset button  24K hard gold plated Resistant to corrosion  In the Box: 100A Circuit breaker with 1/0 AWG or 4 AWG input and output Instruction sheet *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.