Battery & Charger This battery and charger set is designed for sportsmen on the go, with high capacity, a fast recharge time, rugged construction and design features that make it ideal for portable summer and winter use. Great for fly-in trips too. The supplied charger is a fully automatic 1 amp charger/maintainer, so you can expect years of trouble free power when you need it. Features: 12 Volt 9 Amp Battery Capacity Sealed Lead-Acid Design is FAA Approved for flight Fully Automatic 3- Stage Charging 1 Amp 12 Volt Charger Output Charger Will NOT Overcharge the Battery When Full, Maintains the Battery Charge Colored LEDs Indicate Charge Mode Specifications: 12 Volt 9 Amp Capacity Sealed Lead-Acid AGM Battery 12 Volt / 1 Amp DC Charger Output 100 - 240 Volt AC, 22 Watt Charger Input 50/60 Hz Class 2 Battery Charger UL Approved 180 Day Warranty WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

12V Lithium Ion Battery & Charger Lightweight and powerful, the V-120L 12 Volt, 9 amp-hour Vexilar Lithium battery has been designed to replace any current Vexilar Flasher/Pack battery and still allow use of the 1 amp, fully-automatic Vexilar battery charger. Features: Drop-in replacement for any current Vexilar Flasher/Pack battery LiFePO4 technology Delivers twice the number of battery re-charging cycles over sealed lead-acid batteries Half the weight of the sealed lead-acid battery

  The ProNautic Battery Charger from ProMariner is an award-winning charger with features that define the future of marine battery charging. Recognized with the 2010 IBEX Innovation Award, the ProNauticP combines digitally controlled and software-based power conversion technology with global energy management features to deliver global wide range AC input and power factor correction. This allows models to operate off standard household power connections anywhere in the world. The chargers address the trend of using greater numbers of 12-volt electronics on board today's power, sail, cruising and sport fishing boats. Featuring dual digital display screens, the ProNauticP series makes it easy to view real-time charging voltage, amperage and percentage of power out information. The ProNauticP charger automatically removes stress on a fully charged battery by incorporating a built-in conservation mode that reduces float voltage when the unit does not register a load greater than 5 amps over a 72-hour period and re-conditions batteries to improve battery life and reserve power performance every 21 days if in a storage state. ProMariner's Distributed-On-Demand Technology senses and distributes 100% of available charging to any one bank or a combination of all banks; all unused charging amps are distributed to batteries requiring them. The ProNauticP self-calculates absorption & conditioning time based on its ability to analyze the discharge state of the onboard battery banks and incorporates fully automatic temperature compensation as a standard feature on all models. The revolutionary ProNautic battery chargers are now in stock at CLR Marine! Available in amperages ranging from 10 to 60 amps.      Specials   Closeouts    Remanufactured    Rebates  

UP30PV Ultra Pack Combo with Broadband Transducer, Lithium Ion Battery & Charger Vexilar has delivered on the dream of developing a broad band flasher sonar with unmatched interference rejection and signal clarity. Based on the same easy to use, auto-ranging performance platform as the FLX-28, the FLX-30 offers the angler seven frequencies from which to choose, and with 20 IR settings, 140 combinations are available to kill interference once and for all! The magic begins with the world’s first broad band Ice-Ducer™ made from an array of dozens of small crystals. They deliver a wide sonar frequency band from a 19-degree beam at 160 kHz to an 8-degree at 300 kHz. Anglers can fine-tune the display to knock-out interference and sharpen target ID down to ¼". The FLX-30 features night mode, three power level settings, three zoom zones, three manual depth setting ranges to 300 feet and five color palette choices. With Vexilar’s legendary sunlight-readable, 525-segment resolution display now enhanced with broad band technology, it is safe to say you will never look at ice fishing the same way again! The Ultra Pack carry case is the ultimate case design to hold the FLX-30. The Ultra Pack carry case is unique in that it has a totally enclosed 12 volt 9 amp hour lithium-ion battery that can power your Vexilar for days not hours. You use a master power switch to power up the system. The Ultra Pack has an oversize carry handle that can also hold your transducer float, four rod holder positions (one rod holder comes with the system) Three transducer support eye holes and a great cable management system. The Ultra Pack easily fits into a 5 gallon bucket and comes with would not be complete without a Vexilar tackle box and positions to mount other Vexilar accessories like the Flex-Light, Glo-Ring or more rod holders.  BONUS! A FREE soft pack carry case comes with every UP30PV. This system is ready to use right out of the box! Features: Seven frequencies from 160 to 300 kHz 140 interference rejection options (7 frequencies with 20 settings each) Target ID down to 1/4" Digital depth display Day and night display brightness settings Battery status and low-battery alert Three power level settings Three zoom zones Three manual depth setting ranges to 300 feet Five color palette choices Long lasting brushless flasher technology Vexilar’s exclusive broad band Ice-Ducer™ transducer and float 12 volt, 9 amp-hour, Vexilar Lithium battery Fully automatic charger Soft Pack carry case Adjustable rod holder Eye bolt for optional transducer support Master power switch External power posts for accessories Custom Vexilar tackle box Standard two-year limited warranty Specifications: Frequency: 160 kHz, 180 kHz, 200 kHz, 225 kHz, 250 kHz, 275 kHz and 300 kHz Power output: 1,000 watts peak-to-peak (50 watts RMS) Display resolution: 525 segments Current draw: 300 ma at 12V DC Dimensions: 4.4"H x 6"W x 2.5"D Depth Range: Maximum 300 feet Weight: 7 lbs 4.5oz.

Ultra Pack Combo with Lithium Ion Battery & Charger Ultra Pack Fishing Systems The most impressive carry case system ever designed. The Ultra Pack is the ideal name for the most feature packed ice fishing system ever offered by Vexilar. The innovative Ultra Pack System has a 12 volt, 9 amp-hour Vexilar Lithium battery enclosed inside the case, so you don’t need to connect or disconnect your battery after each use. A master power switch powers up your unit, and additional power posts give anglers the option of running other accessories. The case comes with an adjustable rod holder, cable storage cleats, battery charger and even your own Vexilar tackle box! The super tough Ultra Pack will fit into a five gallon bucket. All Ultra Pack Systems are factory assembled and tested here in the USA. Features: High profile for easy access to controls and great display visibility Enclosed battery compartment with Vexilar Lithium 12 volt, 9 amp-hour battery. Includes digital charger Quick charge jack plug for easy charging Ultra Pack fits in a five gallon bucket Adjustable rod holder fits on either side Ice-Ducer® support eye-bolt has three pre-tapped mounting locations around base External power posts for accessories Master On/Off power switch Non-slip bottom The patented Ice-Ducer® system is a self leveling transducer with float for accurate transducer positioning every time Cable storage and holding grips Pre-drilled holes for optional accessories Holder for the Ice-Ducer® transducer Tackle box holder with tackle box included Super strong handle with float holder Available with the FLX-28 or FLX-30BB flasher from Vexilar, the world leader in flasher sonar technology

12V - 12 AH Max Lithium Battery Vexilar’s MAX Lithium Battery delivers 12 volts and 12 amps of power, the most in its class to be a drop-in replacement for existing 12-volt SLA batteries with half the weight. This battery is designed for the outdoor enthusiast on the go, with high capacity, a fast recharge time, rugged construction, and design features that make it ideal for portable summer and winter use. Great for fly-in trips too. FH1000 Fuse Holder Mounted on the positive terminal of your battery are a fuse holder and fuse. Vexilar knows your battery can cause fires if a dead short happens, so we have taken the added safety precaution to include this fuse holder with a 3 amp fuse for your battery. It comes standard with a 3 amp automotive fuse, but you can put in a size fuse from 3 amp to 10 amps. If your sonar system does not power up, check to see if the fuse or fuse holder is loose. If your sonar system does not power up, inspect the fuse itself, if the wire inside the fuse is burnt, the fuse must be replaced Yes, your Vexilar can run without the fuse holder by connecting directly to the battery, but please use it whenever possible for safety purposes. If for some reason you’ve lost your fuse holder or would like to put them on all your Vexilar systems, they are available directly at vexilar.com, part number: FH1000 Lightweight and powerful, the V-200L 12 Volt, 12 amp-hour Vexilar MAX Lithium battery has been designed to replace any current Vexilar Flasher/Pack battery and may still allow the use of the 1 amp, fully-automatic Vexilar battery charger or the recommended new V-420L rapid charger. Features: Drop-in replacement for any current Vexilar Flasher/Pack battery LiFePO4 technology Delivers twice the number of battery re-charging cycles over sealed lead-acid batteries Half the weight of the sealed lead-acid battery

1 AMP Lithium Battery Charger Only The technology of the 1 amp hour V-420 Lithium charger is designed primarily for use in charging Vexilar Lithium batteries, it is the first charger we know that is capable of charging both Lithium and SLA batteries very well. The easy-to-use charger lights show green when you have power and when the battery is fully charged.  Red tells you the charging cycle has engaged. A blinking red light will warn you that the battery is cold or terminal polarity is reversed.  Special charging instructions for SLA batteries can be found at www.vexilar.com.

12V Lithium Ion Battery 9.6 AH LI lightweight and powerful. This 12 Volt 9 amp-hour Vexilar Lithium battery has been designed to replace any current Vexilar Flasher/Pack battery and still allow use of the 1amp fully-automatic Vexilar battery charger. Drop in replacement for any current Vexilar Flasher/Pack Battery LiFePO4 technology Delivers twice the number of battery re-charging cycles over sealed lead-acid batteries 2.75 lbs (Half the weight of the Vexilar SLA battery). 

    Don't miss out on select ProMariner's ProSport Gen 3 Heavy-Duty On-Board Marine Battery Chargers on closeout now! These are on their way and will be in stock next week. Be sure to place your order today!       Specials    Closeouts    Remanufactured    Rebates  

Skylla-i Battery Charger 24/100 (3) 230V Battery Charger The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Features: Rugged - Aluminium epoxy powder-coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible - Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Please refer to the manual for a complete overview of the possibilities.  Synchronized parallel operation - Several chargers can be synchronized with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP cables. Note: Two output and three output chargers cannot be paralleled with each other. Please see the manual for details. The right amount of charge for a lead-acid battery: variable absorption time - When only shallow discharges occur the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. Preventing damage due to excessive gassing: BatterySafe mode - If to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-i will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use: Storage mode - The storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode float voltage is reduced to 2.2V/cell (26.4V for 24V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. To increase battery life: temperature compensation - Every Skylla-i comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations in battery temperature are expected. Battery voltage sense - To compensate for voltage loss due to cable resistance, the Skylla-i is provided with a voltage sense facility so that the battery always receives the correct charge voltage. Suitable for AC and DC supply (AC-DC and DC-DC operation) - The chargers also accept a DC supply. Use as a power supply - As a result of the perfectly stabilized output voltage, the Skylla-i can be used as a power supply if batteries or large buffer capacitors are not available. Li-Ion (LiFePO4) ready - Simple charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the galvanically isolated CAN bus port. Specifications: Input voltage (VAC): 230V Input voltage range (VAC): 185-265V Input voltage range (VDC): 180-350V Maximum AC input current @ 180 VAC: 20A Frequency (Hz): 45-65Hz Charge voltage 'absorption' (VDC): 28.8V Charge voltage 'float' (VDC): 27.6V Charge voltage ‘storage’ (VDC): 26.4V Charge current (A): 3 x 100A (max total output: 100A) Charge algorithm: 7-stage adaptive Battery capacity: 500-1000Ah Charge algorithm (LiFePO4): 3 stages, with on-off control or CAN bus control Temperature sensor: Yes Power supply mode: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) VE.Can communication port: Two RJ45 connectors, NMEA2000 protocol, galvanically isolated. Integrated 12V CAN-bus power supply, 30V DC maximum Synchronized parallel operation: Yes, with VE.Can Forced cooling: Yes Protection: Battery reverse polarity (fuse) / Output short circuit / Over temperature Operating temp. range: -20 to 60°C (Full output current up to 40°C) Material & Colour: aluminium (blue RAL 5012) Battery connection: M8 bolts 230 VAC-connection: screw-clamp 10mm² (AWG 7) Protection category: IP21 Weight: 16 lbs. (7 kg) Dimensions (hxwxd): 405 x 250 x 150 in (16.0 x 9.9 x 5.9mm) Please contact your dealer for any returns, repairs or support issues related to this product.

TRUECharge2 Battery Charger 804-1260-02 60 Amp - 90-265 Vac / 47-63 Hz Now with PARALLEL STACKING FEATURE This NEW feature allows two chargers to work together to combine the output current, achieving up to 120A for large battery banks. "Every RVer who has ever experienced less-than-stellar performances from the stock converter/charger should seriously consider adding the TRUECharge2 to the 12-volt DC battery systems", says Gary Bunzer of RV Doctor. Product Description In addition to meeting global safety and regulatory standards, TRUECharge2 battery chargers feature low electrical interference and efficient, power factor corrected multistage charging. TRUECharge2 battery chargers can be mounted in a variety of positions, given their drip-proof design. TRUECharge2 battery chargers enable quick installation with easy-to-access AC and DC wiring compartments. Auto-ranging AC input voltage capability (90-265 volts AC) makes traveling abroad and handling poor-quality power a breeze. The easy-to-read onboard display can be augmented with an optional remote panel. Performance Features 12V models available in 20A, 40A and 60A Microprocessor-controlled, multistage charging algorithms Settings for two and three-stage charging Settings for flooded, gel, AGM or lead-calcium batteries Auto-ranging universal input voltage (90-265 Vac, 47-63 Hz) is also compatible with a generator or other low-quality power sources Temperature-compensated charging Power factor corrected for efficient charging Battery-equalization feature Ability to charge 'dead' batteries Battery temperature sensor available (Part #808-0232-01) Optional remote panel (#808-8040-00 for 60 A Charger, #808-8040-01 for 20 A & 40 A Chargers) Protection Features Reverse battery polarity protection Drip-proof design Over and under-temperature protection DC over-voltage protection Battery overcharging protection WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

ProSportHD 20 Plus Gen 4 - 20 Amp - 3 Bank Battery Charger ProSportHD Generation 4 boasts a tri-surface heatsink design. This heavy-duty lightweight design delivers significantly faster charging through optimal cooling, while delivering true rated amp output during charge mode.  ProSportHD's enhanced microprocessor and software provides digital features including: fuel gauge style Charge Completion Monitor, Charge Mode, individual Fault indicators and three digitally selectable performance charge profiles for Flooded (lead acid), AGM and GEL batteries. HP AGM profile on ProSportHD 20 Dual only.  Fully automatic 5-stage charging enhances battery performance while extending battery life. System Check OK and Battery Status indicators provide real time installation and battery fault status.  Designed for use in harsh environments with our industrial grade jacketed DC and AC power cables which include molded strain reliefs and wire splitters.  Features: ProMar Digital Technology Microprocessor and software controlled charging technology for fast, precise charging Distributed-On-Demand™ Technology 100% of all available charging amps are utilized by distributing unused charging amps to any one or combination of all batteries as needed Heavy Duty Tri-Surface Extruded Heat Sink Design Upper, lower and rear facing heat sink design for optimal cooling while delivering true rated constant current charging amps during its two charge mode Expanded LED Display with Completion Status Gauge LED fuel gauge style completion status. Four color multi-stage mode LED status bar. Multi-stage Charge Mode, System Check OK, individual Battery Status and Battery Type indication Lightweight Design Up to 40% lighter compared to an epoxy filled charger Auto-Maintain Energy Saver Mode Monitor and auto maintain batteries only when needed to maintain full state of charge. This significantly reduces AC power consumption Fully Automatic 5-Stage Digital Performance Charging 5 Stages: Analyzes, charges, conditions, auto maintains and reconditions batteries once a month during storage periods. Fully charges and extends battery life Built-in Quality and Safety Dual inline waterproof fuses, reverse polarity, over-temperature, over-current, over-voltage and ignition protection. Certified to Marine UL 1236. CEC and DOE listed. FCC Class B Easy Installation and Operation Pre-wired with 6’ AC and DC cables Battery Type: Group 24–31 Flooded, AGM, HP AGM and GEL batteries 3 Year Warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Series Dolphin Battery Charger - 12V, 90A, 110/220VAC - 50/60Hz The Dolphin Series of battery chargers has always been recognized for its outstanding quality, which the manufacturer is proud to support with a 2-year warranty. Due to production on a wide scale, Dolphin is able to offer high-quality, truly international battery chargers at a reasonable price. The Pro Range, which allows battery banks of up to 1000 amps to be charged, can be equipped with an optional touch-view touchscreen. It provides an intuitive display of measurements as well as charging phases (boost, absorption, and float), the allocated available power, and possible operating faults. The Pro range is equipped with communication via CAN bus, which means it can be used professionally in all land and industrial energy management sectors. Features: 12V-90A Dolphin Pro All Dolphin Battery Chargers and accessories are CE-marked and manufactured to UL and ABYC specifications The Pro Touch Range features a built-in TouchView remote in place of the standard display panel on the Pro chargers The Touchview control panel gives the user more information and control of the charger functions LED Display for programming and monitoring functions Temperature sensor for battery compensation Switch mode technology and a three-stage charging design with a power supply Modern, lightweight, and compact design with white aluminum powder-coated casing 4 screw simple install with easy access removable panel ISO 9002-certified manufacturing plant Three-Stage Charging Curve Bulk Stage: A high current is sent to the battery until it reaches approximately 80% of its full charge. Absorption Stage: The voltage level is maintained and the current is reduced until the battery is 100% charged.  Float Stage: Voltage and current are reduced to maintain the battery. Float gives what the battery requires.

Pro Series Dolphin Battery Charger - 24V, 80A, 230VAC - 50/60Hz The Dolphin Series of battery chargers has always been recognized for its outstanding quality, which the manufacturer is proud to support with a 2-year warranty. Due to production on a wide scale, Dolphin is able to offer high-quality, truly international battery chargers at a reasonable price. The Pro Range, which allows battery banks of up to 1000 amps to be charged, can be equipped with an optional touch view touchscreen. It provides an intuitive display of measurements as well as charging phases (boost, absorption, and float), the allocated available power, and possible operating faults. The Pro range is equipped with communication via CAN bus, which means it can be used professionally in all land and industrial energy management sectors. Features: 24V-80A Dolphin Pro (230 VAC 50/60 Hz input voltage only) All Dolphin Battery Chargers and accessories are CE-marked and manufactured to UL and ABYC specifications The Pro Touch Range features a built-in TouchView remote in place of the standard display panel on the Pro chargers The Touchview control panel gives the user more information and control of the charger functions LED Display for programming and monitoring functions Temperature sensor for battery compensation Switch mode technology and a three-stage charging design with a power supply Modern, lightweight, and compact design with white aluminum powder-coated casing Universal AC input with automatic voltage switching 115/230 VAC 50/60 Hz (24V-80A, 24V-100A, and 24V-150A are 230VAC 50/60 Hz ONLY) 4 screw simple install with easy access removable panel ISO 9002-certified manufacturing plant Three-Stage Charging Curve Bulk Stage: A high current is sent to the battery until it reaches approximately 80% of its full charge. Absorption Stage: The voltage level is maintained and the current is reduced until the battery is 100% charged.  Float Stage: Voltage and current are reduced to maintain the battery. Float gives what the battery requires.

Pro Series Dolphin Battery Charger - 24V, 100A, 230VAC - 50/60Hz The Dolphin Series of battery chargers has always been recognized for its outstanding quality, which the manufacturer is proud to support with a 2-year warranty. Due to production on a wide scale, Dolphin is able to offer high-quality, truly international battery chargers at a reasonable price. The Pro Range, which allows battery banks of up to 1000 amps to be charged, can be equipped with an optional touchview touchscreen. It provides an intuitive display of measurements as well as charging phases (boost, absorption, and float), the allocated available power, and possible operating faults. The Pro range is equipped with communication via CAN bus, which means it can be used professionally in all land and industrial energy management sectors. Features: 24V-100A Dolphin Pro (230 VAC 50/60 Hz input voltage only) All Dolphin Battery Chargers and accessories are CE-marked and manufactured to UL and ABYC specifications The Pro Touch Range features a built-in TouchView remote in place of the standard display panel on the Pro chargers  The Touchview control panel gives the user more information and control of the charger functions LED Display for programming and monitoring functions Temperature sensor for battery compensation Switch mode technology and a three-stage charging design with a power supply Modern, lightweight, and compact design with white aluminum powder-coated casing Universal AC input with automatic voltage switching 115/230 VAC 50/60 Hz (24V-80A, 24V-100A, and 24V-150A are 230VAC 50/60 Hz ONLY) 4 screw simple install with easy access removable panel ISO 9002-certified manufacturing plant Three-Stage Charging Curve Bulk Stage: A high current is sent to the battery until it reaches approximately 80% of its full charge. Absorption Stage: The voltage level is maintained and the current is reduced until the battery is 100% charged.  Float Stage: Voltage and current are reduced to maintain the battery. Float gives what the battery requires.