RAM-Mari-Rivet™ Aluminum Pop Rivets (4 QTY) The RAM-MARI-RIVET-4U consists of (4 qty) aluminum 1/8" pop rivets for blind hole mounting . Grip Thickness: 1/16" to 1/4" Installation Instructions:  1. Locate RAM base to desired mounting location, drill holes with 7/32" drill. 2. Place Mari-Rivet™ body all the way through RAM base and pre-drilled 7/32" holes until flange is firmly secured against mounting surface.   3. Insert rivet gun over mandrel head.   4. Clamp rivet gun; this will initiate the jaws to retract, extracting the mandrel, which pulls the mandrel head into the rivet body setting the rivet. At a predetermined tensile load, the mandrel breaks from its head and is discarded.   Weight:  0.04 lbs.

Adjustable Mid Mount Rod Holder Aluminum 1-1/4" or 1-5/16" with Sleeve & Hex Key These rod holders are constructed of marine grade aluminum that has been 100% anodized for functionality and style. Features: Style: Adjustable Mid Mount Fits rails with 1-1/4" or 1-5/6" measured OD Made from Marine Grade Aluminum WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

RAM-Mari-Nut Rubber Expansion Brass Nuts - 4 pack

RAM 1.5" Diameter Ball Mount with 6.25" X 2" Rectangle Base, STANDARD LENGTH Double Socket Arm & 2.5" Round Base The RAM-111U, powder coated marine grade aluminum mount, consists of a double socket arm mount, one 2.5" diameter round base with 1.5" rubber ball and flat 6.25" x 2" rectangular plate. The plate contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more. Rubber ball, socket technology dampens shock and vibration, as well as allows for almost infinite adjustment, perfect viewing angles. For most applications, mount will support up to ten pounds. Material: Powder Coated Marine Grade Aluminum Note: The "U" in the part number reflects product packaged in poly bag. For mounting a GPS puck antenna to this mount, RAM recommends the RAM-338U

RAM 2.25" Diameter Ball Mount with 11" X 3" Rectangle Base, & 3.68" Round Base The RAM-D-111U-C consists of a short double socket arm, 3.68" diameter round base and 11" x 3" rectangular base. The round base contains pre-drilled holes, including two holes at 180 degrees and three holes at 120 degrees. The rectangle base contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more. The RAM-D-111U-C is Compatible With: Garmin Fishfinders and GPS Chartplotters Humminbird Fishfinders and GPS Chartplotters Lowrance Fishfinders and GPS Chartplotters Raymarine Fishfinders and GPS Chartplotters Overall Height: 8.125" Weight Capacity: Up to 15 lbs. Weight: 3.45 lbs. Material: Powder Coated Marine Grade Aluminum Ball Size: 2.25" Rubber "D" Ball Size Note: The "U" in the part number reflects product packaged in poly bag. The 11" x 3" rectangle base is a universal mounting bracket with a selection of mounting hole locations. In certain applications additional holes may need to be drilled for proper fit with your electronic device.

5" Extruded Aluminum Tough-Track™ With the RAM Tough-Track™, flat surface mounting possibilities are nearly endless for ATVs, cars, combines, motorboats, tractors, trucks and more. The extruded aluminum version of the RAM Tough-Track can be drilled to any flat surface and is designed for use with #8 screws for easy installation – hardware not included. Made to be a dependable and rugged mounting solution, the anodized aluminum provides a smooth slide across the track and anti-corrosion protection. The RAM-TRACK-EXA-5U features 5” of usable track length, while the included top loading end caps add about 1.5” in length each. Using the end caps allows for two installation options: either use both top loading end caps to create insertion points on both ends of the track, or use one top loading end cap and close the opposite end with the included flush end cap. The Extruded Aluminum Tough-Track is compatible with the RAM Center Loader and 90 Degree Connector, as well as a wide variety of RAM track bases to attach devices like action cameras, fishing rods, phones and tablets. Material: Marine-grade aluminum and high-strength composite Note: Part number reflects product packaged in clear bag polybag. Weight: 0.21 lbs.

17" Extruded Aluminum Tough-Track™ With the RAM Tough-Track™, flat surface mounting possibilities are nearly endless for ATVs, cars, combines, motorboats, tractors, trucks and more. The extruded aluminum version of the RAM Tough-Track can be drilled to any flat surface and is designed for use with #8 screws for easy installation – hardware not included. Made to be a dependable and rugged mounting solution, the anodized aluminum provides a smooth slide across the track and anti-corrosion protection. The RAM-TRACK-EXA-17U features 17” of usable track length, while the included top loading end caps add about 1.5” in length each. Using the end caps allows for two installation options: either use both top loading end caps to create insertion points on both ends of the track, or use one top loading end cap and close the opposite end with the included flush end cap. The Extruded Aluminum Tough-Track is compatible with the RAM Center Loader and 90 Degree Connector, as well as a wide variety of RAM track bases to attach devices like action cameras, fishing rods, phones and tablets. Material: Marine-grade aluminum and high-strength composite Note: Part number reflects product packaged in clear polybag. Weight: 0.42 lbs.

13" Extruded Aluminum Tough-Track™ With the RAM Tough-Track™, flat surface mounting possibilities are nearly endless for ATVs, cars, combines, motorboats, tractors, trucks and more. The extruded aluminum version of the RAM Tough-Track can be drilled to any flat surface and is designed for use with #8 screws for easy installation – hardware not included. Made to be a dependable and rugged mounting solution, the anodized aluminum provides a smooth slide across the track and anti-corrosion protection. The RAM-TRACK-EXA-13U features 13” of usable track length, while the included top loading end caps add about 1.5” in length each. Using the end caps allows for two installation options: either use both top loading end caps to create insertion points on both ends of the track, or use one top loading end cap and close the opposite end with the included flush end cap. The Extruded Aluminum Tough-Track is compatible with the RAM Center Loader and 90 Degree Connector, as well as a wide variety of RAM track bases to attach devices like action cameras, fishing rods, phones and tablets. Material: Marine-grade aluminum and high-strength composite Note: Part number reflects product packaged in clear polybag. Weight: 0.36 lbs.

3" Extruded Aluminum Tough-Track™ With the RAM Tough-Track™, flat surface mounting possibilities are nearly endless for ATVs, cars, combines, motorboats, tractors, trucks and more. The extruded aluminum version of the RAM Tough-Track can be drilled to any flat surface and is designed for use with #8 screws for easy installation – hardware not included. Made to be a dependable and rugged mounting solution, the anodized aluminum provides a smooth slide across the track and anti-corrosion protection. The RAM-TRACK-EXA-3U features 3” of usable track length, while the included top loading end caps add about 1.5” in length each. Using the end caps allows for two installation options: either use both top loading end caps to create insertion points on both ends of the track, or use one top loading end cap and close the opposite end with the included flush end cap. The Extruded Aluminum Tough-Track is compatible with the RAM Center Loader and 90 Degree Connector, as well as a wide variety of RAM track bases to attach devices like action cameras, fishing rods, phones and tablets. Material: Marine-grade aluminum and high-strength composite Note: Part number reflects product packaged in clear polybag. Weight: 0.17 lbs.

9" Extruded Aluminum Tough-Track™ With the RAM Tough-Track™, flat surface mounting possibilities are nearly endless for ATVs, cars, combines, motorboats, tractors, trucks and more. The extruded aluminum version of the RAM Tough-Track can be drilled to any flat surface and is designed for use with #8 screws for easy installation – hardware not included. Made to be a dependable and rugged mounting solution, the anodized aluminum provides a smooth slide across the track and anti-corrosion protection. The RAM-TRACK-EXA-9 features 9” of usable track length, while the included top loading end caps add about 1.5” in length each. Using the end caps allows for two installation options: either use both top loading end caps to create insertion points on both ends of the track, or use one top loading end cap and close the opposite end with the included flush end cap. The Extruded Aluminum Tough-Track is compatible with the RAM Center Loader and 90 Degree Connector, as well as a wide variety of RAM track bases to attach devices like action cameras, fishing rods, phones and tablets. Material: Marine-grade aluminum and high-strength composite Note: Part number reflects product packaged in clear polybag. Weight: 0.28 lbs.

RAM 1.5" Ball Mount with 6.25" X 2" Rectangle Base, Double Socket Arm & Track Ball™ Base The RAM-111B-354-TRA1U consists of a Track Ball™ base that can attach to any track system including the RAM Tough-Track™. Connected to the base is a standard length double socket arm and 6.25" x 2" rectangle plate for supporting a wide range of fishfinders and chartplotters. The rectangular plate contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more. Material: Powder Coated Marine Grade Aluminum and High Strength Composite Ball Size: 1.5" Rubber Ball Size Note: Part number reflects product packaged in clear polybag for store shelf display. The 6.25" x 2" rectangle base is a universal mounting bracket with a selection of mounting hole locations. In certain applications additional holes may need to be drilled for proper fit with your electronic device.

RAM 1" Diameter Ball Mount with 6.25" X 2" Rectangle Base & 2.5" Round Base The RAM-B-111U, powder coated marine grade aluminum mount, consists of a double socket arm mount, one 2.5" diameter round base with 1" rubber ball and flat 6.25" x 2" rectangular plate. The plate contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more. Rubber ball, socket technology dampens shock and vibration, as well as allows for almost infinite adjustment, perfect viewing angles. For most applications, mount will support up to three pounds. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag. For mounting a GPS puck antenna to this mount, RAM recommends the RAM-338U

RAM 3.68" Diameter Base w/Ball The (RAM-240U), marine grade aluminum base, consists of a 1.5" diameter rubber ball connected to a flat 3.68" diameter base. This base has pre-drilled holes that connects to RAM Tough-Dock Powered Docking Stations. Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag.

Description: The RAM-111U-B consists of a 2.5" diameter round base that contains the universal AMPs hole pattern, SHORT LENGTH double socket arm and 6.25" x 2" rectangle base. The rectangle base contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more. Compatible Devices: Garmin Fishfinders/Chartplotters Humminbird Fishfinders/Chartplotters Lowrance Fishfinders/Chartplotters Raymarine Fishfinders/Chartplotters Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size

The RAM-111U-D consists of a 2.5" diameter round base that contains the universal AMPs hole pattern, LONG LENGTH double socket arm and 6.25" x 2" rectangle base. The rectangle base contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more. The RAM-111U-D is Compatible With: Garmin Fishfinders and GPS Chartplotters Humminbird Fishfinders and GPS Chartplotters Lowrance Fishfinders and GPS Chartplotters Raymarine Fishfinders and GPS Chartplotters Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size