RAM-Mari-Nut Rubber Expansion Brass Nuts - 4 pack

Top-Mounted Flag Pole Socket CP/Brass - 3/4" ID Features: CP/Brass Top Mounted Flag Pole Socket Tube I.D. - 3/4" Base - 2" Height - 1-3/4" Fastener - #6(3)

Top-Mounted Flag Pole Socket Polished Brass - 3/4" ID Features: Polished Brass Top Mounted Flag Pole Socket Tube I.D. - 3/4" Base - 2" Height - 1-3/4" Fastener - #6(3)

RAM-Mari-Rivet™ Aluminum Pop Rivets (4 QTY) The RAM-MARI-RIVET-4U consists of (4 qty) aluminum 1/8" pop rivets for blind hole mounting . Grip Thickness: 1/16" to 1/4" Installation Instructions:  1. Locate RAM base to desired mounting location, drill holes with 7/32" drill. 2. Place Mari-Rivet™ body all the way through RAM base and pre-drilled 7/32" holes until flange is firmly secured against mounting surface.   3. Insert rivet gun over mandrel head.   4. Clamp rivet gun; this will initiate the jaws to retract, extracting the mandrel, which pulls the mandrel head into the rivet body setting the rivet. At a predetermined tensile load, the mandrel breaks from its head and is discarded.   Weight:  0.04 lbs.

RAM Pin-Lock™ Security Kit and 1.5" Diameter C Size Mount for Gimbal Brackets The RAM-SG-111U consists of a 2.5" diameter round base, STANDARD LENGTH double socket arm, 6.25" x 2" rectangle base, RAM mixed combination Pin-Lock security™ nut/knob and key knobs for Gimbal Brackets. The 6.25" x 2" rectangle base is a universal mounting bracket with a selection of mounting hole locations. In certain applications additional holes may need to be drilled for proper fit with your electronic device. RAM® Pin-Lock™ security solutions are designed to withstand the harshest environments where RAM® Mounts are commonly used. With an emphasis on aesthetics and function, RAM® security nuts/knobs are low profile and only add a small amount of additional bulk to your system when compared to the standard knob included. At a fraction of the cost of currently available keyed locking knobs, the additional peace of mind and tamper resistance comes at a very affordable price. The included threaded key knob replaces the gimbal knob, assuring your mounted electronic device is safe from theft and tampering. Features Overall Height: 7.35" Weight Capacity: Up to10 lbs Material: Powder Coated Marine Grade Aluminum and High Strength Composite Ball Size: 1.5" Rubber Ball Size

RAM Pin-Lock™ Security Kit and 1.5" Diameter Ball Mount with 6.25" X 2" Rectangle Plate The RAM-S-111U consists of a 2.5" diameter round base, STANDARD LENGTH double socket arm, 6.25" x 2" rectangle base, RAM mixed combination Pin-Lock security™ nut and key knob. The 6.25" x 2" rectangle base is a universal mounting bracket with a selection of mounting hole locations. In certain applications additional holes may need to be drilled for proper fit with your electronic device. RAM® Pin-Lock™ security solutions are designed to withstand the harshest environments where RAM® Mounts are commonly used. With an emphasis on aesthetics and function, RAM® security nuts/knobs are low profile and only add a small amount of additional bulk to your system when compared to the standard knob included. At a fraction of the cost of currently available keyed locking knobs, the additional peace of mind and tamper resistance comes at a very affordable price. Features Overall Height: 7.35" Weight Capacity: Up to 10 lbs Material Powder Coated Marine Grade Aluminum and High Strength Composite Ball Size: 1.5" Rubber Ball Size

Handlebar Rail Mount w/Long Arm & Diamond RAM Handlebar Rail Mount with LONG Length Double Socket Arm & Zinc Coated U-Bolt Base for Rails from 0.5" to 1.25" in Diameter The RAM-B-149ZU-C consists of a zinc coated u-bolt base, LONG Length double socket arm and diamond adapter base. The diamond adapter base has a hole pattern that matches the industry standard AMPS hole pattern and will connect to a large variety of RAM Mount and third party cradles. Included in this package is hardware that will accommodate rails from 0.50" to 1.25" in diameter. A composite rail adapter can narrow the rail to a minimum width of 0.5”. The mount is designed with a RAM 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. Features: Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber "B" Ball Size Note: The "U" in the part number reflects product packaged in poly bag. Weight: 0.85 lbs.

Light Diffuser for Type D Peanut Bulb - Red - 4 Pack Features: Red in color Application - Type D Peanut Bulbs *Sold as a 4 Pack WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Light Diffuser for Type D Peanut Bulb - Green - 4 Pack Features: Green in color Application - Type D Peanut Bulbs *Sold as a 4 Pack WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

RAM Seat-Mate Laptop Mounting System for Laptop and Notebooks Computers Universal Vehicle Fitment RAM Seat-Mate Description: Compact, portable, amazingly strong and no tools required are words that best describe the new RAM Seat-Mate. Able to transform most any passenger seat into a workstation, simply unpack the mount from the compact bag, unfold the legs, and buckle it in. Truly innovative in design, this product is able to actively hold onto the seat and stabilize itself. For anyone who needs a temporary mobile workstation, this mounting solution is absolutely perfect. Designed to easily pack into a travel bag, suit case, or even under the seat of a vehicle, RAM makes it possible to create a comfortable workspace in minutes where ever your job takes you. The RAM Seat-Mate? is perfect for laptops, tablets, and UMPC?s. The integrated rubber ball and socket system allows the user to achieve ergonomic viewing and typing angles. If you're a mobile professional, this product was designed for you. Material: High Strength Composite & Powder Coated Marine Grade Aluminum The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics. Tough-Tray Dimensions: Tray Depth: 10.0" Tray Thickness: 2.125" Tray Width (Expansion): 10" to 16" Side Clamp Arm Height: 0.5" (min) to 1.75" (max) Material: High Strength Composite Note: Part number reflects product packaged in clear clam shell for store shelf display. The Tough-Tray is compatible with laptops that have 17" screens. If the Tough-Tray Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-n-Motion kit.

Vehicle Base Compatible Vehicles: DODGE RAM 1500-5500 (2008-2011) This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board. DRILLING REQUIREMENTS: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Weight: 2.1 lbs. Material: Powder Coated Steel Dimensions: A = 14.75", B = 3.8", C = 1.75", Hole Center = 13.25" Features: Quick installation with no drilling needed. Rock solid construction with lifetime warranty. Low profile keeps mount away from passenger leg space. Won?t interfere with levers or factory-installed console or 4WD lever. Designed to accommodate trucks with PTO Swing Arm The RAM RAM-VP-SW1-89, combination swing arm/tele-pole system, will connect to any RAM vehicle base without a welded female tele-pole. Included is a tele-pole with a height range from 11.5" to 17"; it can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray. The double swing arm with rotating plate, allows you to twist and tilt the viewing angle of your laptop, tablet, UMPC, monitor, or any other connected electronic device, when mounted on your RAM Vehicle Mount. Taking the highly successful RAM Vehicle Mounts to the next level, this rotating swivel arm gives you even more viewing positions for your mounted electronic device while holding everything firmly in place. The length of the double swing arm is 12". Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball "C" Size Note: Part number reflects product packaged in clear clam shell for store shelf display. Laptop Mount Tray The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics. Tough-Tray Dimensions: Tray Depth: 10.0" Tray Thickness: 2.125" Tray Width (Expansion): 10" to 16" Side Clamp Arm Height: 0.5" (min) to 1.75" (max) Material: High Strength Composite Note: Part number reflects product packaged in clear clam shell for store shelf display. The Tough-Tray is compatible with laptops that have 17" screens. If the Tough-Tray Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-n-Motion kit.

RAM Flat Surface Mount w/Cradle for Garmin dēzl GPS RAM Cradle Holder for the Garmin dēzl 560LMT & 560LT: This RAM high strength composite cradle is designed to hold the following devices: Garmin dēzl 560LMT Garmin dēzl 560LT Features: Open access to all electronic ports including audio port, speaker/mic and mini USB Patent pending roller design for super smooth placement and removal of the GPS Custom pocket for factory dock Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag. The cradle includes a set of two nuts and bolts to connect the cradle to any of the RAM compatible mounts. RAM cradles do not include the RAM-B-238U (Diamond Base & Ball) or RAP-B-238U (Diamond Composite Base & Ball), required to attach to the cradle and RAM mounting system. Surface Mount: Simply choose your preferred mounting location and the possibilities become endless with the RAM-B-138U. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. RAM's design also dampens shock and vibration helping to extend the life of your device. Material: Powder Coated Marine Grade Aluminum

Ram Pin-Lock™ Security Kit f/ 1" B Size Mounts and Gimbal Brackets You make a significant investment in the equipment you purchase to make your job or hobby easier or more enjoyable. Whether it's a high end piece of marine electronics, a GPS for your motorcycle, or a tablet used for business purposes, you need to protect your investment. RAM® Mounts protect your device from harmful shock and vibration, but what about theft and tampering? RAM® offers a full suite of security products which protect your device while mounted on your RAM® mount from theft and unwanted tampering. Simply add a security knob or nut to your RAM Mount to deter would-be thieves from targeting your equipment. RAM® security solutions are also a great way to add tamper resistance to your RAM® Mount in situations where there is a desire to prevent end-users from adjusting the mount or removing the device. High strength composite and brass construction assures a long life of trouble free use in a wide variety of environments including marine and salt water.

Vehicle Base Ford F-150 (2004-2010) Ford F-150 (2004-2010) Lincoln Mark LT (2005-2010) This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. Placement of Mount: Passenger side floor board, under seat Drilling Requirements: No - uses existing seat bolts Seat Configuration: Bucket/bench Pole: Purchased Separately Weight: 9.1 lbs. Material: Powder Coated Steel Features: Quick installation with no drilling needed. Rock solid construction with a lifetime warranty. The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics. Tough-Tray Dimensions: Tray Depth: 10.0" Tray Thickness: 2.125" Tray Width (Expansion): 10" to 16" Side Clamp Arm Height: 0.5" (min) to 1.75" (max) Material: High Strength Composite The RAM RAM-VP-SW1-89, combination swing arm/tele-pole system, will connect to any RAM vehicle base without a welded female tele-pole. Included is a tele-pole with a height range from 11.5" to 17"; it can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray. The double swing arm with rotating plate, allows you to twist and tilt the viewing angle of your laptop, tablet, UMPC, monitor, or any other connected electronic device, when mounted on your RAM Vehicle Mount. Taking the highly successful RAM Vehicle Mounts to the next level, this rotating swivel arm gives you even more viewing positions for your mounted electronic device while holding everything firmly in place. The length of the double swing arm is 12". Material: Powder Coated Marine Grade Aluminum

RAM Short Double Socket Arm with Jam Nut for 2.25" Ball Bases Part #: RAM-D-201U-C-MI1 The RAM-D-201U-C-MI1, short double socket arm with jam nut, has a socket at both ends that accommodates 2.25" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infinite adjustment and perfect viewing angles. Dimensions: Overall Length: 5.0625" Socket-To-Socket Length: 3.1875" Material: Powder Coated Marine Grade Aluminum Ball Size: 2.25" Rubber Ball "D" Size