|
Tsunami Bilge Pump T1200 - 12V - 1200 GPH
With their innovative engineering and compact design, Tsunami pumps deliver high output from a small package. We use the advanced material available, including the best quality bearings and state-of-the-art brushes, alloys and magnets. Our patented shaft seal prevents leaks caused by misalignment and out caulked and tinned wiring eliminates wicking, prevents water damage and resists corrosion.
Boaters, boat-builders, and dealers all want one thing from their bilge pumps - more power! And that's what the Tsunami Series delivers... with high-capacity, high-efficiency output Tsunami Cartridge pumps have replaceable / interchangeable motor cores. Makes servicing simple and quick.
Features:
Outlet Style - Barbed - 1-1/8"
12V
1200 GPH
29" Wire
3-Year Warranty
|
23.99 |
|
|
Tsunami T800 GPH Bilge Pump
Part #: 4608-7
With their innovative engineering and compact design, Tsunami pumps deliver high output from a small package. We use the advanced material available, including the best quality bearings and state-of-the-art brushes, alloys and magnets. Our patented shaft seal prevents leaks caused by misalignment and out caulked and tinned wiring eliminates wicking, prevents water damage and resists corrosion.
Boaters, boat-builders and dealers all want one thing from their bilge pumps - more power! And that's what the Tsunamir Series delivers... with high-capacity, high-efficiency output. Tsunami Cartridge pumps have replaceable/interchangeable motor cores. Makes servicing simple and quick.
Features:
Outlet Syle - Barbed - 3/4"
12V
29" Wire
3-Year Warranty
|
29.99 |
|
|
Shower Sump Pump System - 500 GPH
Part #: 4141-4
Attwood's shower sump systems deliver the performance you've been asking for. Standard Box size that offers fast water flow into and out of sump. The lid snaps in to allow quick installation (and removal for cleaning) and includes a gasket to seal the sump box against overflow. The sump box even includes an air to prevent air locks. Meets or exceeds all applicable of the ABYC and USCG.
Features:
36" Wire
12V
Standard Box Size
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
113.33 |
|
|
Shower Sump Pump System - 750 GPH
Part #: 4143-4
Attwood's shower sump systems deliver the performance you've been asking for. Large Box size that offers fast water flow into and out of sump. The lid snaps in to allow quick installation (and removal for cleaning) and includes a gasket to seal the sump box against overflow. The sump box even includes an air to prevent air locks. Meets or exceeds all applicable of the ABYC and USCG.
Features:
36" Wire
12V
Large Box Size
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
122.60 |
|
|
Walbro FRA-1-1 Electric Fuel Pump
Voltage: 12V DC
Weight: 1.63 lb
Minimum Flow Rate: 20 gph
Dry Lift: 24"
Service Life: 5,000+ hr
Fuse: 5A
Current Draw: 2.0 Amps
Inlet/Outlet: 1/8-27 NPSF
Inlet Filter Screen: 70 Micron
Magnetic Trap: None
Outlet Check Valve: No
Maximum Output Pressure: 4.0 - 7.0 psi
The FRA Series electric fuel pump operates at a constant frequency — it will continue to cycle as long as electric power is supplied.
If there is no demand for fuel, the pump will build pressure in the fuel delivery line - up to its rated maximum pressure - and continue to cycle, but with no fuel output.
As such, it is not well-suited for continuous operation/low demand applications such as heater or stove systems, since it will constantly make noise, and have a shortened service life due to high cycling.
For stove/heater and continuous duty applications, use the Walbro FRD series of pumps, which addresses these issues. See Related Products, below.
An FRA pump can be used, however, to fill a gravity-feed day tank commonly used in diesel stove and heater installations.
FRA pumps incorporate a new piston mechanism which, unlike rubber diaphragms, is not affected by modern, high-tech fuel blends.
The FRA is designed to serve as a primary pump (replacing a mechanical fuel pump) or as an auxilliary fuel pump (assisting the existing pump) for internal combustion engines.
The pump self-regulates to its pre-set pressure, pumping more or less fuel as the delivery pressure (head) varies.
FRA pumps are commonly used as replacements for failed mechanical fuel pumps on older engines, where the owner doesn't want to continue using a pump with a rubber diaphragm susceptable to degradation by modern alcohol fuel blends.
They are also commonly used in open flow, low head applications such as fuel polishing.
• Non-adjustable maximum output pressure is factory pre-set in the ranges indicated below
• Output pressure can be further regulated by screwing in, or placing in-line, an adjustable pressure regulator such as the HOL 12-804
• FRA provides low cost with good durability
• Compatible with all commercially available pump grade gasoline, gasoline-alcohol blends, diesel, and bio-diesel fuels
• Continuous duty life (diesel fuel): >5,000 hours
• Flow rates as high as 52 gph, but 30 gph is a more typical maximum
• Current draw averages less than 2 amps
• Self-priming to at least 2 feet; maximum dry run time is 4 hours
• Inlet (bottom)/Outlet (top): 1/8-27 NPSF (Dryseal American National Standard Straight Pipe Thread) — will accept NPT tapered fittings without leaking, thread sealant recommended
• No internal filter - a 70 micron, or finer, pre-filter is recommended
• USCG 16623-1 and 16623-2 approved; ignition protected
• Dichromate coating passes 96 hour salt spray test - not recommended where exposed to saltwater
• Dimensions: 5.43"H x 2.76"Dia.
• Note - a suffix number (typically -1 or -2) in part number refers to type of packaging
• Made in USA
Technical
Selecting among the Walbro FR Series electric fuel pumps:
• All the FR electric pumps provide fuel until the fuel demand decreases, or flow is restricted - but they have different mechanisms for doing so.
FR pumps will cycle (pump) until they build up the pressure (head) in the outflow line - with an accompanying decrease in fuel flow - and reach their factory preset maximum pressure.
At this point, constant frequency pumps like the FRA will continue cycling - but no fuel will flow.
Variable frequency pumps, like the FRB and FRD, will slow and eventually stop cycling as the pressure builds.
If the pressure on the outflow side of the pump drops, both types of pump will start supplying fuel again.
• Choosing an FR Series pump is often less dependent on the application, and more a matter of user preference:
— FRA pumps are lower cost, basic models.
They have no built-in filter, and their constant cycling means electric current draw is constant - regardless of output, they are always making noise, they typically have a shorter lifespan (higher wear), and they can wear unevenly as the stroke can be shortened when operating near their maximal pressure.
— FRB and FRD pumps have a more expensive variable frequency circuit board, always use their full stroke length - so wear is evenly distributed, do not always operate at full capacity/maximal cycling — so less wear, longer life, less noise, and lower average current draw.
Additionally, the FRB models include a built-in/replaceable 70 micron mesh filter, so the user doesn't need to supply a pre-filter.
• What the FR fuel pump is designed to do:
— In carbureted applications - The FRA and FRB fuel pumps self-regulate to their maximum output pressure when the carburetor bowl is full, and respond to float movement in the carburetor as required.
When the engine demands more fuel, the pump increases its flow rate.
When the engine demand drops, the pump reduces its flow rate.
— In diesel applications - The FRA and FRB pumps will deliver fuel to the diesel injector pump, assuring a positive pressure at the injector pump inlet.
These pumps are designed to refill diesel filters after service or replacement.
— In transfer applications, including fuel polishing, FRA and FRB pumps run continuously, as long as electrical power is supplied to the pump, and output back pressure is low.
— In diesel heater and stove applications, the task-specific FRD pumps will slow their cycling rate to deliver only the fuel required by the stove fuel metering valve ("carburetor").
FRD pumps can also fill day tanks in gravity feed installations.
|
331.94 |
|
|
Little Giant& Sub. Sump Pump 526003
Little Giant NK-1 Submersible Pump
Motor 115 Volt 60 Hz 1/150 HP Permanently Lubricated Oil Filled Motor, 210 GPH at 1 Foot Head, Shutoff Head 10.2 Feet, Inlet: Screened, Outlet: 1/4" MNPT or 1/2" Tubing with Elbow Fitting, Nylon Body, Fluid Temperature Up to 120F (49C), 6 Foot Power Cord
526003 For commercial, industrial, and home use worldwide where liquid must be transferred or recirculated. Applications include aquariums, swimming pools, water displays, ice makers, air conditioners, boat bailing, fuel oil transfer, circulating water for welding and pipe threading machines, pumping mild chemicals such as soap solutions, acids, plating solutions and fertilizers.
|
182.52 |
|
|
Little Giant Sub. Pump 518200
Little Giant PE-1 Submersible Pump
Motor 115 Volt 60 Hz 1/125 HP Epoxy Encapsulated Oil-Less Direct Drive Motor, 170 GPH at 1 Foot Head, Shutoff Head 7 Feet, Inlet: Smooth Volute with Snap Off Screen, Outlet: 1/4" MNPT or 1/2" Tubing, Fluid Temperature Up to 120F (49C), UL/CSA Listed, 6 Foot Power Cord
518200 Small submersible, epoxy-encapsulated pump for commercial, industrial, and home use. Applications include statuary fountains, water displays, air conditioners, machine tools, and many other applications where liquid must be transferred or recirculated.
Not recommended for fuel oil transfer, aquariums, and swimming pools.
|
127.92 |
|
|
Tsunami MK2 Manual Bilge Pump - T1200 - 1200 GPH & 12V
The Tsunami Mk2 is the only manual bilge pump that eliminates airlocks. This is done by the Patented X-Air™ Impeller, which ejects trapped air in the pump and pipework. Also, the Tsunami Mk2 is the most reliable manual bilge pump in freshwater applications, considering it has 40% better protection against water ingress and electrolysis vs. the Mk1 pump.
Easy Installation & Service
GPH (Gallons Per Hour): 1200
90° rotatable elbow outlet allows users to install the pump anywhere in a full 360° orientation
Backward compatible hole pattern and motor cartridges of Tsunami Mk1 bilge and aerator pumps
External mounting feet and integrated outlet reduces time and effort
Service pump cartridges from hard-to-reach areas using only one hand
Specifications:
Rated Volts DC: 12V
Fuse Size: 5 Amp
Wire Length: (inch) 29" / (mm) 735
Hose Diameter: (inch) 1" and 1-1/8"
*Must be used with appropriate Tsunami outlet
|
53.88 |
|
|
Tsunami MK2 Manual Bilge Pump - T1200 - 1200 GPH & 24V
The Tsunami Mk2 is the only manual bilge pump that eliminates airlocks. This is done by the Patented X-Air™ Impeller, which ejects trapped air in the pump and pipework. Also, the Tsunami Mk2 is the most reliable manual bilge pump in freshwater applications, considering it has 40% better protection against water ingress and electrolysis vs. the Mk1 pump.
Easy Installation & Service
GPH (Gallons Per Hour): 1200
90° rotatable elbow outlet allows users to install the pump anywhere in a full 360° orientation
Backward compatible hole pattern and motor cartridges of Tsunami Mk1 bilge and aerator pumps
External mounting feet and integrated outlet reduces time and effort
Service pump cartridges from hard-to-reach areas using only one hand
Specifications:
Rated Volts DC: 24V
Fuse Size: 2 Amp
Wire Length: (inch) 29" / (mm) 735
Hose Diameter: (inch) 1" and 1-1/8"
*Must be used with appropriate Tsunami outlet
|
50.35 |
|
|
Tsunami Mk2 T1200 Aerator - 12V - 1" NPT Inlet
Keep bait and fish alive with the Tsunami Aerator Mk2. Attwood’s leading fish-friendly technology is making it easier to install and service while offering new installation options never provided by the Tsunami range.
Features:
7/8" x 1" seacock
Flexible installation with both 90 and straight inlets and outlets
Full backward compatibility with previous Tsunami models
Faster, smarter installation with no sealant or tools is required
Specifications:
Flow Gallon/Hour: 1200
|
51.40 |
|
|
Tsunami Mk2 T1200 Aerator - 12V - 90-Degree Inlet
Keep bait and fish alive with the Tsunami Aerator Mk2. Attwood’s leading fish-friendly technology is making it easier to install and service while offering new installation options never provided by the Tsunami range.
Features:
3-1/2" x 1-1/8" thru-hull
Flexible installation with both 90 and straight inlets and outlets
Full backward compatibility with previous Tsunami models
Faster, smarter installation with no sealant or tools is required
Specifications:
Flow Gallon/Hour: 1200
|
50.00 |
|
|
Tsunami Mk2 T1200 Aerator - 12V - Straight Inlet
Keep bait and fish alive with the Tsunami Aerator Mk2. Attwood’s leading fish-friendly technology is making it easier to install and service while offering new installation options never provided by the Tsunami range.
Features:
3-1/2" x 1-1/8" thru-hull
Flexible installation with both 90 and straight inlets and outlets
Full backward compatibility with previous Tsunami models
Faster, smarter installation with no sealant or tools is required
Specifications:
Flow Gallon/Hour: 1200
|
48.20 |
|
|
Tsunami Mk2 T500 Aerator - 12V - 3/4" NPT Inlet
Keep bait and fish alive with the Tsunami Aerator Mk2. Attwood’s leading fish-friendly technology is making it easier to install and service while offering new installation options never provided by the Tsunami range.
Features:
7/8 in. x 3/4 in. seacock
Flexible installation with both 90 and straight inlets and outlets
Full backward compatibility with previous Tsunami models
Faster, smarter installation with no sealant or tools is required
Specifications:
Flow Gallon/Hour: 500
|
33.91 |
|
|
Tsunami Mk2 T800 Aerator 12V 3/4" NPT Inlet
Keep bait and fish alive with the Tsunami Aerator Mk2. Attwood’s leading fish-friendly technology is making it easier to install and service while offering new installation options never provided by the Tsunami range.
Features:
7/8 in. x 3/4 in. seacock
Flexible installation with both 90 and straight inlets and outlets
Full backward compatibility with previous Tsunami models
Faster, smarter installation with no sealant or tools is required
Specifications:
Flow Gallon/Hour: 800
|
40.08 |
|
|
Tsunami Mk2 T500 Aerator - 12V - Straight Inlet
Keep bait and fish alive with the Tsunami Aerator Mk2. Attwood’s leading fish-friendly technology is making it easier to install and service while offering new installation options never provided by the Tsunami range.
Features:
3-1/2 in. x 3/4 in. thru-hull
Flexible installation with both 90 and straight inlets and outlets
Full backward compatibility with previous Tsunami models
Faster, smarter installation with no sealant or tools is required
Specifications:
Flow Gallon/Hour: 500
|
31.57 |
|