FI5002 NMEA2000 Junction Box The FI5002 is an NMEA2000 Certified, 6-Port Junction Box for use with for use with any NMEA2000 network. The FI5002 features 2 NMEA2000 backbone ports, as well as 6 NMEA2000 ports. It will support up to 2A or 40 (LEN) on a 12VDC network.The FI5002 will also support 24VDC networks. Features 2 NMEA2000 backbone ports 6 NMEA2000 ports Less than 2A power requirement on a 12VDC system WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 T-Connector  Furuno's NMEA2000 T-Connector for Female/Female/Male.  This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 Power Tee - 8M - 2x Female Connector  Furuno's NMEA2000 Power Tee with 8 Meter, 2x Female connector. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 Micro Terminator - Male  Furuno's NMEA2000 Micro Terminator with male connector. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 Micro Terminator - Female  Furuno's NMEA 2000 Micro Terminator with female connector. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 Drop Cable - 6M 6M DROP CABLE NMEA2000 f/ PB200 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NavLink 2  “NavLink 2 is an easy to fit NMEA 2000 to Wifi server designed to make NMEA 2000 navigation data available for apps on smartphones, tablets, iPads and PCs.” Features: NavLink 2 is an easy to fit NMEA 2000 to Wifi server designed so that NMEA 2000 navigation data can be made available for apps on smartphones, tablets, iPads and PCs. Installation takes seconds as a result of direction connection to the NMEA 2000 back bone and self-powered from the data network. Once installed, it creates a local WiFi network for devices to connect or can be programmed to join an existing wireless network if one is already installed.  This is ideal for devices like the Furuno wireless radar which require operation through their own dedicated network but require NMEA 2000 data integration for charting apps. NavLink 2 now works with the popular Navionics Boating App for Apple iOS and Android. Therefore allowing display of GPS and AIS data on your Navionics charts.  Specifications: NMEA 2000 to WiFi server Self powered from NMEA 2000 bus – fits in seconds Supports TCP/IP and UDP connection modes Provides AIS, navigation and instrument data to apps Compatible with all popular apps like iNavX, TimeZero, Weather 4D, Navionics, SailGrib, NavLink, iSailor, SeaPilot, AquaMap etc Up to 7 connected devices Compatible with Windows, Linux, MAC OS, iOS and Android Easy web interface for programming Password protected Can act as dedicated wireless server or rather can connect to an existing wireless network Diagnostic data display mode and LED status lights Internal hi gain WiFi antenna Super-fast 230KBs operation Optional raw data mode for developers and likewise advanced users Supplied with NMEA 2000 cable

veKonvert NMEA 2000 Gateway veKonvert brings NMEA 2000 connectivity to Victron’s popular SmartShunt battery monitoring system. Now a navigation multi-function display becomes a sophisticated battery and energy management system. Features veKonvert is a stand-alone NMEA 2000 interface designed in conjunction with Victron Energy to integrate VE.Direct compatible devices such as their SmartShunt, BMV Battery Monitors, and MPPT Solar Charge Controller range into NMEA 2000 systems. This functionality already existed but required the use of a sophisticated Cerbo module. veKonvert is a lower-cost, simpler solution for smaller installations that just need the electrical data displayed on a multi-function display. Boaters and boat builders like a clear and uncluttered dash or nav area, so integrating electrical data into the main navigation display is a popular and cost-saving option. The product is a collaboration between Victron Energy and Digital Yacht. The system utilizes Victron’s proprietary VE.Direct data connectivity as a source for the NMEA 2000 data. Victron solar panel controllers (MPPTs) and battery monitors can now also interconnect to NMEA 2000 via the veKonvert interface. Installation Installation is simple – just "T" into the NMEA 2000 backbone and plug into the VE.Direct custom connector on the SmartShunt, and you've got battery and electrical data on your NMEA 2000 network! Specifications: Universal NMEA 2000 gateway for Victron products with a VE.Direct interface (see compatibility list in the FAQ tab) Enables battery management or solar charge monitoring on compatible multi-function displays (Raymarine, Garmin, Navico, Furuno, etc) Provides battery voltage, charge/discharge current, state of charge, and time to depletion based on a sophisticated algorithm Easy installation, plug ‘n’ play connectivity, and self-powering from the NMEA 2000 bus Generates NMEA 2000 alerts from any BMV or SmartShunt Alarms Supports multiple SmartShunts for a larger multi-battery system Vekonvert Is Compatible with the Following Victron Products: BMV -700, BMV -702, BMV -700H, BMV-712 Smart, BMV-710H Smart, BMV-712 Smart Rev2, SmartShunt 500A/50mV, SmartShunt 1000A/50mV, SmartShunt 2000A/50mV, and All MPPT Charge Controllers NOTE: veKonvert is not compatible with Victron Chargers and Inverters. It should also not be plugged into the VE.Direct interfaces of any Victron "Consumers" such as Multiplus, Quattro, Cerbo, etc.

30 Meter Cable Kit w/ Junction Box, FI5001

50 Meter Cable Kit w/ Junction Box, FI5001 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MS-NRX300 Remote Control - Wired NMEA 2000 Features: Multi-Zone Technology Install the MS-NRX300 wired remote anywhere onboard the vessel, in the flybridge, cockpit, saloon or cabin for example and gain full localized control of one or up to four individual audio zones. NMEA 2000 Certified Certified for connection to any NMEA 2000 network making installation straight forward, saving time and money. Once connected, the wired remote will double as a NMEA 2000 repeater displaying supported NMEA data on screen. Complies With IPx7 Waterproof Standards. Perfect for installation on a swim platform or deck, the MS-NRX300 wired remote control is designed for the marine environment. Designed specifically for the marine environment, featuring a 3 year warranty. Flush & Dash Moutning Options.  Innovative design allows an installer the option of either mounting the wired remote with a conventional dash finish or an option to integrate into a glass helm with a flush surface mount. Superior Optically Bonded LCD Display  Large high contrast daylight viewable 2.6" optically bonded LCD will display crystal clear data/track information and prevent moisture build up or fogging. Specifications: NMEA 2000 Certified LEN: 3 Large 2.6" Monochrome optically bonded LCDgh contrast daylight viewable in direct sunlight Adjustable backlit LCD Dash or Flush mount installation options Local zone control or all zone control (up to 4 zones) Complies with IPx7 waterproof standards STM32 Micro Processor Rotary encoder Advanced user interface 'Positive feel' rubber keypad In the Box: MS-NRX300 Remote w/attached 1 M Drop Cable Dust Cover 6 M NMEA 20000 Backbone Cable NMEA 2000 T-Connector NMEA 2000 Female Terminator NMEA 2000 In-line Terminator Hardware mounting kit Mounting template WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Auto Glide Boat Leveling System for Single Actuator Tab Systems w/Existing NMEA 2000 A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again! The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad. The main components are the Auto Glide Key Pad, the Auto Glide Control Box, the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver. Boat must have Lenco Single Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications. For Aftermarket Systems: The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System: For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains 1 30254-001D Auto Glide Key Pad Control 1 30255-001 Auto Glide Control Box f/ Single Actuator 1 30248-001 Auto Glide Control Box Harness f/ Single Actuator 1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5' Available for these CANbus-based engines: NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki E Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Lenco Auto Glide Boat Leveling System f/Dual Actuator Tab Systems w/Existing NMEA 2000 A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again! The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad. The main components are the Auto Glide Key Pad, the Auto Glide Control Box , the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver. Boat must have Lenco Dual Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications. For Aftermarket Systems: The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System: For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains 1 30254-001D Auto Glide Key Pad Control 1 30256-001 Auto Glide Control Box f/ Dual Actuator 1 30247-001 Auto Glide Control Box Harness f/ Dual Actuator 1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5' Available for these CANbus-based engines: NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

GPS 24xd GPS Antenna w/ Heading Sensor - NMEA 2000  EXPLORE COASTAL WATERS The GPS 24xd position receiver and antenna gives you precise location with multi-band GNSS and heading accuracy even at slow speeds. Navigate in more locations with expanded GNSS support.  Get high-sensitivity tracking with fast GPS update rate.  Accurately pinpoint your heading — regardless of speed. It’s water-resistant (IPX7) to withstand the elements. Install it easily with multiple mounting options.  The antenna is compatible with NMEA 2000® devices. Multi-Band GNSS Multi-band GNSS provides location accuracy to within 1 meter to compatible marine multifunction displays, instrument displays and autopilots. Magnetic Heading The magnetic heading sensor provides accuracy to within 3 degrees, stabilizing charts, radar overlay and MARPA even at slow speeds. High-Sensitivity GPS Fast 10 Hz position update rates provide high-sensitivity position, velocity and time data. Expanded GNSS Support GPS 24xd provides access to four key global navigation satellite systems (GPS, Galileo1, GLONASS and BeiDou1) to more accurately track in challenging conditions than GPS alone. Multi-SBAS Compatible Multi-SBAS compatibility corrects signal measurement errors and provides information about the accuracy, integrity, continuity and availability of its signals. Mounting Options Installation is easy with under-deck, pole and surface-mount options. In The Box: GPS 24xd NMEA 2000® Pole mount Surface mount Under deck mount NMEA 2000 backbone/drop cable (6 meters) NMEA 2000 T-connector Documentation

SB-2G Junction Box Cable Seal - 2 Pack Upgrade your Scanstrut Junction Box to IP67 Waterproof standard. This Cable Seal upgrade kit is available to upgrade your Junction Box to IP67.  The IP67 cable seals screw into the boxes at the cable entrance points and can accept cables from 0.15” to 0.48" (4 to 12mm). Features: Watertight installation - 100% waterproof with an IP67 rating. Dome-shaped profile provides a stronger, impact-resistant design and outer dome provides additional water shield. Compatible With: SB-8-5 Junction Box  SB-8-10 Junction Box Technical Specifications: Fits cable size (diameter) - .15" to .48" (4 - 12 mm)   Color - Grey Material - Marine grade polypropylene In the Box: Two (2) cable seals Mounting hardware Installation manual *Sold as a Pair