|
12.5" Dual Mount for Most Radar Domes - Top for Sat Domes - Top Plate Required
Install your satdome, camera or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. Oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or a open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them. *Top Plate Sold Separately*
|
1008.00 |
|
|
22.5" Dual Mount for Up To 4.5' Open Array Radar - Top for Sat Domes - Top Plate Required
Install your satdome, camera or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. Oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or a open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them. *Top Plate Sold Separately*
|
1488.00 |
|
|
13.25" Pre-Drilled Dual Mount for Most Closed Dome Radars - Black - Top Plate Required
Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
*Top Plate Sold Separately
|
1032.00 |
|
|
23.75" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required
Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
*Top Plate Sold Separately
|
1512.00 |
|
|
28" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required
Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
*Top Plate Sold Seperately
|
2078.40 |
|
|
16.75" Dual Mount Pre-Drilled for Most Closed Dome Radars Top for FLIR Searchlight Satellite Domes
Install your satdome, camera or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. Oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or a open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
|
1996.80 |
|
|
The Vision Series Mounting System is a revolutionary design that provides the simplest, most attractive solutions to your electronics mounting requirements. Dual Mount for a Radar Dome and a Satellite Dome. Two Mounting Plates required.
Features:
All-new sleek, modern design
First all modular system - extremely versatile
Simple selection and installation
Easy to add accessories
Two marine electronics mounting platforms
Powder coated aluminum
Requires Vision Mounting Plate to install radar or sat dome antenna
18" Sat Dome Dual Mount
Aft raked 30 degrees
18" tall
|
934.67 |
|
|
The Vision Series Mounting System is a revolutionary design that provides the simplest, most attractive solutions to your electronics mounting requirements. Dual Mount for a Radar Dome and a Satellite Dome. Two Mounting Plates required.
Features:
All-new sleek, modern design
First all modular system - extremely versatile
Simple selection and installation
Easy to add accessories
Two marine electronics mounting platforms
Powder coated aluminum
Requires Vision Mounting Plate to install radar or sat dome antenna
24" Sat Dome Dual Mount
Aft raked 30 degrees
24" tall
|
1511.05 |
|
|
5" Modular Mount Aft Raked 7x7 Base Top Plate Required - Black
This Seaview Modular Radar Mount works with 18" - 24" closed dome radars. The modular design allows you to add various accessories and different top plates at any point, thus making it a cost effective choice. A Seaview Modular Top Plate is required and sold separately!
Modular Top Plate
A Seaview Modular Top Plate is required to mount a radar, satellite dome, camera or search light, and is sold separately.
Modular Design
The modular design allows the user to not have to replace the entire mount when a different radar or satdome is used. Instead the user can just replace the top plate.
Compact Design
Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must.
|
254.40 |
|
|
5" Modular Mount FWD Raked 7" x 7" Base Plate - Top Plate Required
This Seaview Modular Radar Mount works with 18" - 24" closed dome radars. The modular design allows you to add various accessories and different top plates at any point, thus making it a cost effective choice.
Modular Top Plate
A Seaview Modular Top Plate is required to mount a radar, satellite dome, camera or search light, and is sold separately.
Modular Design
The modular design allows the user to not have to replace the entire mount when a different radar or satdome is used. Instead the user can just replace the top plate.
Compact Design
Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must.
|
240.00 |
|
|
5" Modular Mount AFT Raked 7" x 7" Base Plate - Top Plate Required
This Seaview Modular Radar Mount works with 18" - 24" closed dome radars. The modular design allows you to add various accessories and different top plates at any point, thus making it a cost effective choice.
Modular Top Plate
A Seaview Modular Top Plate is required to mount a radar, satellite dome, camera or search light, and is sold separately.
Modular Design
The modular design allows the user to not have to replace the entire mount when a different radar or satdome is used. Instead the user can just replace the top plate.
Compact Design
Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must.
|
240.00 |
|
|
12" AFT Leaning Mount for Searchlights & Thermal Cameras with 7" x 7" Base Plate
Seaview 5" and 12" tall aft leaning mounts for thermal cameras and searchlights. Powder-coated brilliant white gives it a nice clean look and yet is very durable. Specifically designed for installations where space is very limited. The base for this mount is 7″ x 7″.
Cable Management
A hollow oval mast section provides plenty of room for cable management.
Space-Saving Design
The small 7"x 7" base footprint makes this a great solution to an installation where space is an issue.
|
427.20 |
|
|
Dual Mount - 33"
Install your satdome, camera or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. Oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or a open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
Fits the Below Electronics:
18" - 24" closed dome radars
16" - 18" satdomes
Cameras
|
1670.40 |
|
|
MEGA Live TargetLock & MEGA 360 Dual Mount for Ultrex
The MEGA Live TargetLock and MEGA 360 Dual Mount for Ultrex provide the components needed to mount a MEGA Live TargetLock and MEGA 360 Imaging accessory transducer on a Minn Kota Ultrex™ bow-mount trolling motor.
Features:
Dual Mount and mounting hardware for installing a MEGA Live TargetLock and MEGA 360 Imaging transducer on a Minn Kota® Ultrex trolling motors.
Compatible with MEGA Live TargetLock – Ultrex 45 -52”, MEGA Live TargetLock Adapter Kit – Ultrex 45”-52”, and MEGA 360 Imaging – Ultrex.
This kit does not include MEGA Live TargetLock, MEGA Live Imaging Transducer, or MEGA 360 Imaging Transducer.
1-Year Limited Warranty
What's Included?
Dual Mounting Bracket for MEGA Live TargetLock and MEGA 360 Imaging-Ultrex
Mounting Hardware
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
207.43 |
|
|
Suncover for Axiom 12 when Front Mounted for Non Pro
Raymarine Axiom 12 Suncover when using Front Mounting Kit
|
71.58 |
|