|
SeaTalkngT-Piece Connector. Used for connecting white SeaTalkng Spur Cables to Blue SeaTalkng Backbone Cables.
|
35.78 |
|
|
The SeaTalkng Backbone kit contains everything you need to construct and wire a basic SeaTalkng navigation network backbone on board your vessel.
The kit contains the following components:
A06031 SeaTalkng Terminators (Qty. 2)
A06037 Backbone Cable, 20m
A06036 Backbone Cable, 5m (Qty. 2)
A06028 T-Piece (Qty. 4)
A06049 Network Power Cable
81300 SeaTalkng Reference Manual
ST70 Displays, transducer pods, transducers and network spurs are not included.
|
284.99 |
|
|
Raymarine SeaTalkng Starter Kit
SeaTalkng is a robust cabling and connection system compatible with NMEA 2000, built specifically for the marine environment comprising a powered single backbone with two terminators, one at each end.
The SeaTalk to SeaTalkng Starter Kit is the perfect way to get started with your SeaTalkng compatible Raymarine product.
The 5-way connector forms the start of your SeaTalkng backbone and your SeaTalkng product is connected via a Spur Cable.
What's in the kit?
A06064: SeaTalkng 5-way Connector
A06031: SeaTalkng Backbone Terminator (x2)
A06040: SeaTalkng Spur Cable 3M
A06049: SeaTalkng Power Cable
|
119.99 |
|
|
Evolution Cabling Kit - R70160
The Evolution SeaTalkng cable kit contains:
1 x SeaTalkng Power Cable (0.4m)
1 x SeaTalkng Backbone Cable (5m)
1 x SeaTalkng Spur Cable (0.4m)
1 x SeaTalkng 5-way Connector Block
2 x SeaTalkng T-piece Connector
2 x SeaTalkng Terminator
|
215.21 |
|
|
Backbone Cables
In a SeaTalkng installation, a backbone cable runs through the length of the boat.
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.
Two backbone cable lengths can be joined together by part A06030, a backbone extender.
|
40.90 |
|
|
Backbone Cables
In a SeaTalkng installation, a backbone cable runs through the length of the boat.
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.
Two backbone cable lengths can be joined together by part A06030, a backbone extender.
|
46.01 |
|
|
Backbone Cables
In a SeaTalkng installation, a backbone cable runs through the length of the boat.
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.
Two backbone cable lengths can be joined together by part A06030, a backbone extender.
|
51.12 |
|
|
Backbone Cables
In a SeaTalkng installation, a backbone cable runs through the length of the boat.
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.
Two backbone cable lengths can be joined together by part A06030, a backbone extender.
|
61.36 |
|
|
Backbone Cables
In a SeaTalkng installation, a backbone cable runs through the length of the boat.
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.
Two backbone cable lengths can be joined together by part A06030, a backbone extender.
|
92.03 |
|
|
Backbone Cables
In a SeaTalkng installation, a backbone cable runs through the length of the boat.
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.
Two backbone cable lengths can be joined together by part A06030, a backbone extender.
|
76.69 |
|
|
5-way SeaTalkng Connector used for connecting spurs to the backbone.
|
46.01 |
|
|
SeaTalkng Terminators attach at each end of SeaTalk backbone. Two are required per system.
|
25.56 |
|
|
SeaTalkng Backbone Extender for extending blue SeaTalkng Backbone Cables.
|
30.67 |
|
|
SeaTalk hs Network Cable, 10m
Raymarine SeaTalk hs network cables provide waterproof, reliable, high-speed connections between E-Series components.
Available in multiple lengths to simplify installation, the network cable locks positively into E-Series displays, switches and couplers. A 1.5 meter SeaTalk hs cable is supplied with each E80 and E120 display.
|
184.99 |
|
|
SeaTalk hs Network Cable, 20m
Raymarine SeaTalk hs network cables provide waterproof, reliable, high-speed connections between E-Series components.
Available in multiple lengths to simplify installation, the network cable locks positively into E-Series displays, switches and couplers. A 1.5 meter SeaTalk hs cable is supplied with each E80 and E120 display.
|
286.36 |
|