B260 Bronze Thru Hull The B260 will enhance fish detection on virtually all of today's fish finders. High-performance has been redefined with its Broadband Ceramic Technology. The narrow, 6 degree beam 200 kHz ceramic will give you excellent resolution and crisp image detail needed for bottom fishing. The B260's low ringing is perfect for finding fish holding tight to the bottom and other structure. The seven-element 50 kHz array has a wider 19 degree beam for deeper blue-water fishing. The outcome at both frequencies is excellent resolution and crisp image detail where it's needed most. Compatible with Lowrance HDS Series and Simrad NSE Series Multifunction Display Units. Features Depth/Temp 50/200 kHz 1 kW RMS High-performance Bronze Thru Hull 7 pin blue connector Includes High Speed Fairing Block

B258 1kW Bronze Thru-Hull Depth/Temp with FB - 8-Pin Garmin's bronze, thru-hull mount transducer with fairing provides depth and temperature data. Garmin's transducer has an operating frequency of 50 or 200 kHz and mounts on a 0-22° deadrise angle. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

B45 Bronze Thru-Hull with Fairing Block - 50/200 kHz - 600W - 9-Pin Connector (xSonic) The B45 is Airmar’s smallest and most economical, dual-frequency, bronze, stem transducer. It features a single, 50/200 kHz ceramic element. The included fairing streamlines the transducer and increases the performance—even at higher speeds. Features The depth and fast-response water-temperature sensing 600 W of power Dual-frequency element: 50 kHz with a wide 45° beamwidth for depth performance to 353 m (1200') 200 kHz with a 12° beamwidth for depth performance to 206 m (700') Excellent performance and sensitivity in a small housing Bronze housing with High-performance Fairing for optimal performance at speed Specifications Acoustic Window: Urethane Cable-Length: 10 m (33') Common Use: Cruising/Racing Sailboats, Leisure/Yachting, Fishing Connector: Simrad 9-Pin, Lowrance 9-Pin, Navico 9-Pin Conventional Beam: 45°/12° Country of Origin: USA Cross Reference: 000-13946-001 Deadrise Range: Up to 28° with fairing Display Connector: 9N Frequency Band: 50/200 kHz Hole Size: 22 mm (7/8") Housing Material: Bronze Hull Material: Fiberglass or wood Max Deadrise: Up to 26° with fairing Max Deadrise Angle: 26° Max Depth: Low frequency- 366 m (1200'), High frequency- 206 m (700') Max Vessel LOA: Up to 9 m (30') Mix and Match Series: 5-Pin 600 Watt Mounting Style: Thru-Hull with Fairing Power Rating: 600 W Sensor Connector: MM Single or Dual Frequency: Conventional Dual Frequency Tilted Element: No Transducer Functions: Depth, Temperature Usable Shaft Length: 92 mm (3.62") Weight: 2.5 kg (5.5 lb.) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

SS75 High Chirp 12 Degree Bronze Thru-Hull xSonic Transducer Airmar’s low-profile, Chirp-ready transducer models are the perfect addition to smaller boats, such as center consoles. The high-frequency band has a narrow beamwidth, excellent for pinpointing fish holding tight to wrecks, reefs, and other structures. High frequency also shows amazing target separation on baitfish and schooling gamefish. The SS75H transducer, operating at 130 to 210 kHz, delivers up to 80 kHz of total bandwidth in just one installation for outstanding bottom detail and fish-target resolution. This Tilted Element™ transducer has the element fixed at a 12-degree angle within the housing. Because the transducer is installed almost flush with the hull, the tilt corrects for the hull deadrise. It orients the ceramic element horizontally to ensure maximum echo returns to the transducer. Features: Depth and fast-response water-temperature sensing 600 W of power with a maximum depth of 214 m (700') High frequency (130 to 210 kHz) 15- 9 degree beamwidth High frequency delivers great shallow-water performance, bottom detail, and clear fish-target returns Low-profile, thru-hull housing provides good display resolution at speed when installed properly Recommended for stepped, planning, or displacement hull Stainless steel housing for use in all hull materials Patented Xducer ID® technology Specifications: Brand: Airmar Technology Acoustic Window: Urethane Cable-Length: 10 m (33') Common Use: Fishing, Commercial Fishing Connector: Simrad 9-Pin, Lowrance 9-Pin, Navico 9-Pin Country of Origin: USA Cross Reference: 000-13912-001 Deadrise Range: 8-15 degrees Display Connector: 9N Frequency Band: High Functions: Depth, Temperature High Frequency: 130-210 kHz High Frequency Beamwidth: 15-9 degrees Hole Size: Fiberglass or wood hull—70 mm or 2-13/16", Metal hull—79 mm or 3-1/8" Hull Material: Compatible w/ all hull materials Material: Stainless Steel Max Deadrise: Up to 24 degrees Max Deadrise Angle: 24 degrees Max Depth: 214 m (700') Max Vessel LOA: Up to 8 m (26') Mix and Match Series: 12-Pin Chirp Mounting Style: Tilted Element Thru-Hull Power Rating: 600 W Retractable housing: No Sensor Connector: MMC Single or Dual Frequency: CHIRP-Ready Single-Band Tilt Angle: 12 degrees Tilted Element: Yes Weight: 1.4 kg (3 lbs.) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B75H 20° Bronze Thru-Hull CHIRP xSonic 9-Pin The B75H is a bronze, thru-hull, tilted, high-frequency (130-210kHz), depth and temperature transducer. The ceramic element is tilted for built-in deadrise compensation, giving excellent echo returns for more accurate depth readings.  Features: CHIRP transducers enable bottom detection with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures Depth/Temperature - Calculates how deep the water is, so that you can avoid running aground, whilst also incorporating a temperature sensor for accurate water temperature readings Easy To Install High Frequency - CHIRP range is 130kHz-210kHz for good target detail in shallow water and excellent bottom tracking in deep water Highly Accurate - Provides extremely accurate data 20° Tilt - The 20° tilt is ideal for boats with a 16° to 24° hull deadrise Low Profile - The low profile housing minimizes drag with just 5mm extending outside of the hull Plug & Play Connection - Easily connect to NSS, NSE, NSO or Lowrance

xSonic B150M Thru-Hull Transducer - 9-Pin 10M Cable - 0° As CHIRP continues to redefine recreational fishing, AIRMAR has expanded the lineup of broadband transducers to satisfy the growing demand for this game changing technology. The B150M economical CHIRP transducers designed for offshore fishing and freshwater anglers. Operating at a frequency range of 95-155 kHz, these transducers reveal fish in shallow, murky waters at medium depths (up to 2,500 feet*) along with ultra-clear target resolution.  *Depths vary depending on target strength and sea conditions  A tilted element model in the CHIRP Thru-Hull product line, the B150M CHIRPS across the following bandwidth: M Model - Medium Frequency 95-155 kHz    Features: Depth and water temperature sensor 300W Bronze Thru Hull 0° tilt Ideal for inshore or coastal fishing in shallow to medium depths Freshwater anglers will see fish holding close to structures and suspended fish  Track bottom at higher boat speeds More coverage under your boat delivers wider archesand 26° to 17° beamwidths  Cover the medium frequency range-CHIRPs from 95-155kHz to provide 60 kHz of total bandwidth from one transducer Hull Type: Fiberglass, wood 1 internal ceramic

GT12M Bronze Thru-Hull - 350W - 20 Degree Designed for reduced drag and optimum sonar performance on midsize fishing and cruising boats, this flush-mounted, 350-watt mid-band CHIRP transducer clearly defines fish arches, structure, and bottom depth returns on your display. Midband Chirp Traditional Sonar This 8-pin, 350-watt bronze thru-hull transducer features high-definition mid-band CHIRP sonar that clearly defines fish targets and structures down to 800’ in saltwater and 1,200’ in freshwater. Broad Frequency Range Use the perfect frequency for the waters you’re fishing. Covering the medium frequency range, this transducer pulses from 85–165 kHz, displaying a wide coverage area, crisp fish arches, and accurate depth readings. Optimum Ping Sensitivity Offering excellent sonar sensitivity, low noise, high resolution, and good separation of targets, this robust transducer makes it easier than ever to distinguish fish and structure on your compatible chartplotter display. Thru-Hull Installation A durable bronze housing and stem offer straightforward thru-hull flush mounting for minimum drag and optimum beam orientation for clear sonar returns. Auto-ID Technology Enjoy simple plug-and-play operation with Garmin auto-identification technology — which enables the sonar to automatically configure itself to the transducer being used. Fits Various Hull Types Configurable for a wide variety of boat hull materials, including fiberglass, composite, and wood, the transducer is available in a range of tilt versions to accommodate deadrise angles of 0–20° without a fairing block. In the Box: GT12M-THF transducer Jam nut Washer Documentation Specifications: Transducer Frequency: Medium band CHIRP (85-165 kHz) Transducer Power: 350 W Transducer Beamwidth: 24° -16° Transducer Maximum Depth: 800 ft saltwater / 1200 ft freshwater Transducer Cable Length: 50 ft Transducer Depth/Speed/Temperature: Depth, temperature Transducer Number of Pins: 8-pin Housing Material: Bronze Transducer Supported Deadrise/Transom Angles: 20° supports hull deadrise angles from 16° to 24°

RealVision 3D™ Bronze Thru-Hull Transducer Pair Pack - 20° - 8M Cable & Y-Cable Designed for inboard or outboard boats, the RV-220 Bronze Through Hull Transducer System lets you easily identify structures and locate fish with the life-like clarity of RealVision 3D™ sonar. The RV-220 system is a 4-channel, Wide Spectrum CHIRP transducer system with DownVision™, SideVision™, high frequency CHIRP fish targeting and RealVision 3D™ sonar inside. The transducer system has a built-in attitude and heading reference system (AHRS) that stabilizes the sonar imagery, automatically compensating for vessel motion. You’ll enjoy crystal-clear imagery in waves, swells, and while maneuvering. The RV-220 system also has a built-in fast response water temperature sensor for quick, accurate readings. Raymarine’s RV-220 Bronze Through Hull Transducer system pack contains a pair of RealVision 3D transducers with internal offset to accommodate hull deadrise angles from 13° to 20°. This completely eliminates the need for fairing blocks. The low-profile design slips effortlessly through the water without causing drag or cavitation. The near-flush RV-220 system works great on trailered boats too. The RV-220 system features rugged cast-bronze through hull bodies suitable for fiberglass or wooden hulls. One transducer transmits and receives to port and downwards, the other to starboard and downwards, ensuring a full 180° of underwater coverage even on boats with deep keels or other underwater protrusions. Each transducer features a 2M pigtail, joining y-cable and 8-meter extension cable, resulting in an overall cable length of 10M (33'.) What’s in the Box? RV-220P Bronze Port Transducer with 2M cable RV-220S Bronze Starboard Transducer with 2M cable RealVision 3D Transducer Y-Cable RealVision 3D 8M (26') Transducer Extension Cable Anti-rotation bolt kit Installation instructions

B619 20° Tilt Bronze Thru-Hull Transducer - 8-Pin Minimize Your Drag The B619 model have been the standard in low-profile models for many years. Their large sensitive ceramics allow deep echosounding up to 206M (700'). These nearly flush units minimize drag as only 5mm (2/10") of the housing extends outside of the hull. The bronze B619 provides a vertical beam without a fairing. Inside the housing, the ceramic element is tilted to provide built-in deadrise compensation. The resulting vertical beam provides excellent echo returns for moreaccurate depth readings. Applications: Cruising powerboats and sailboats Sailboats Features: Depth only or Depth and temperature Fixed 20° tilted versions for 16° to 24° hull deadrise Right angle cable exit offers low headroom and protection when transducer is stepped on Included rubber washer allows tightening of the hull nut to irregular hull surfaces Housings are ABYC H-27 compliant Optional temperature sensor Bronze housing Boat Size: Up to 9M (30') WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Bronze Thru-hull Wide Beam Transducer w/Depth & Temp - 20° Tilt, 8-Pin - Airmar B175HW Step up to 1 kW without a fairing with this flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull and can sit on the trailer rollers/bunks without damage. The tilted element inside the transducer accommodates all hull deadrises and eliminates the need for a fairing block. Low, medium, high, and high wide versions provide maximum flexibility for the choice of frequencies. An excellent choice for fiberglass and wood hulls, this 8-pin transducer has a depth of 600'; an operating frequency of 150-250 kHz; a beamwidth of 25°; and a 16 to 24° deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Bronze Thru Hull Transducer Bronze Thru-Hull Transducers are for large boats and for boats with in-board motors that make typical Transom Mount Transducers ineffective. They are not recommended for trailered boats as the transducer is not flush with the hull. Bronze Thru-Hull Transducers require that a hole be drilled in the hull and the shaping of a fairing block. Professional installation is recommended. Plastic Thru-Hull Transducers are an alternative to Bronze Thru-Hull Transducers. Description: Bronze thru hull transducer, single or dual beam use. 20/60 degree, 200/83kHz. Transducer dimensions: 5.25L X 2.75"W X 1.2"D (below hull); Shaft diameter: .86". Fairing block not included. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

B265LH Bronze Thru-Hull CHIRP Transducer - 12-Pin Bronze, Thru-Hull CHIRP Transducer with 12-Pin Connector, Low-Freq: 42-65 kHz, High-Freq: 130-210 kHz. The B265LH is a bronze thru-hull CHIRP transducer for use with Furuno's CHIRP broadband Fish Finders. The B265LH comes complete with high-speed fairing block Traditional marine Fish Finders operate at discrete frequencies such as 50 kHz and 200 kHz, use relatively short-duration transmit pulses, and use narrowband sonar transducers. In contrast, CHIRP (Compressed High-Intensity Radar Pulse) uses a precise sweep pattern of many frequencies within a long-duration transmit pulse from a broadband transducer. The equivalent sound energy transmitted into the water is 10 to 1,000 times greater than a conventional marine Fish Finder. The echo energy returning to the transducer is likewise superior to that generated by a conventional transducer. The combination of CHIRP, a broadband transducer, and Furuno’s superior Digital Signal Processing, results in dramatically increased fish and bottom detection. The B265LH CHIRPS across the following bandwidths:  Low-Frequency: 42-65 kHz High-Frequency: 130-210 kHz This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B175HW CHIRP Bronze Thru-Hull 12° Tilt 1kW - 10-Pin Connector High-Frequency, Wide-Beam CHIRP Transducer with Temperature with Bronze Thru-Hull with 12° Tilt. Features: Power: 1kW Function: Depth,Temperature Frequency: 150-250 kHz Mount Style: Thru-Hull, Flush, 12 Degree Tilt Housing Material: Bronze 10-Pin Connector This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B265LH Bronze Thru-Hull Mount Transducer w/Depth & Temp - 12-Pin Garmin's best performing 1 kW thru-hull transducer, this mount performs well in deep water and has exceptional bottom and water column detail. This transducer has a depth of 3,000 feet; an operating frequency of 42 to 65 kHz and 130 to 210 kHz; a beamwidth of 16 to 25 degrees and 6 to 10 degrees; and a 0 to 20 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. Compatible Devices: GPSMAP® 7607xsv, 7608xsv, 7610xsv, 7612xsv, 7616xsv GSD™ 25 Premium Sonar Module WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

DST-810MSF Bronze Thru-Hull, Digital Depth, Speed, Temp Sensor, NMEA2000  Airmar B617V Housing Style Transducer The DST-801MSF offers depth, speed, and temperature in a single, 51 mm (2”) fitting. Only one hole through the hull simplifies the installation — an attractive feature for boat builders and boat owners alike. Patented, speed-signal-processing and upgraded 5 Hz (5X per second) speed-through-water enhancements provide excellent paddlewheel accuracy below 5 knots (6 MPH) and smooth linear output at all vessel speeds. The transducer’s wide, fan-shaped, fore-aft beam is able to find bottom even when installed on steep deadrise hulls or heeling sailboats. You also get true water-temperature readings with the DST-810MSF's reliable temperature sensor. The DST-810MSF features a new Wireless connectivity to Airmar's CAST App, allowing you to calibrate the sensor, add depth offsets, and more. Features: Depth, speed, and temperature in one compact bronze housing Fast-response temperature sensor provides ±0.2°C (±0.1°F) accuracy Weight: 1.6 kg (3.5 lb) Acoustic Window: Urethane Hull Deadrise: Up to 22° Data Update Rate: 1 per second Minimum Sounding Depth: 0.5 m (1.6’) Maximum Sounding Depth: 70 m (230’) Pressure Rating: 3 m (10’) Pulse Rate: 20,000 p/nm* (5.6 Hz per knot)—*p/nm = pulses per nautical mile Smart Sensor Supply Voltage at 100% Sound Power Output: 11.5 VDC to 25 VDC Supply Current: 40 mA Standard Cable Length: 6m NMEA 2000® Load Equivalency Number (LEN): 4 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.