Tuthill 2RC2AS-RH Reversible Cast Iron Gear Pump End Tang Shaft
The Tuthill 2RC2AS-RH is a size 2 cast iron gear pump end from the C Series, moving a nominal 9 GPM through 1 inch NPT inlet and outlet ports. It ships as the pump end alone, without a motor or a drive. Pumping action comes from a rotor and an idler gear either side of a crescent cast integral with the cover. Two moving parts means very little to wear, and the series is rated across a wide viscosity band from 40 to 10,000 SSU.
This build is reversible cover with a shaft seal, which sets its pressure envelope: inlet pressure to 25 PSI, maximum differential pressure of 100 PSI and maximum discharge pressure of 100 PSI. There is no internal relief valve on this build, so a positive displacement pump like this one needs an external bypass somewhere in the discharge piping before it is put to work. The R in the model code is the reversing feature. On a reversing C Series pump the cover can be rotated through 180 degrees to move the suction port to the other side, so one pump covers both piping layouts without a new housing. The RH suffix is the suction location as supplied. Like all C Series pumps it must not be used on plain water, corrosive liquids or abrasive slurries, and it must never be run dry.
Key Features
- Cast iron internal gear construction with only two moving parts
- Nominal capacity of 9 GPM through 1 inch NPT inlet and outlet ports
- Reversible cover with a shaft seal
- Wide viscosity range of 40 to 10,000 SSU covers thin oils through heavy stock
- Straightforward wet end with no internal valve to set or maintain
- Rotors in forged steel with sintered steel idler gears and precision bronze bearings
- Reversing design lets the cover rotate 180 degrees to change the suction side
Applications
- Lubrication circuits on air compressors, gas compressors and gearboxes
- Burner oil and fuel oil transfer and circulation
- Low pressure hydraulic supply and control circuits
- Heat transfer oil, quench oil and process oil circulation
- Original equipment packages built around a bare gear pump end
- Transfer duty on viscous non abrasive industrial fluids
Specifications
- Brand: Tuthill
- Manufacturer Part Number: 2RC2AS-RH
- Part Type: Rotary gear pump end, no motor supplied
- Series: C Series, size 2
- Nominal Capacity: 9 GPM
- Ports: 1 inch NPT inlet and outlet
- Mounting: Reversible cover
- Shaft Seal: Shaft seal
- Rotation: Reversible, tang shaft drive
- Housing and Cover: Cast iron ASTM A48
- Rotor: Forged steel
- Idler Gear: Sintered steel
- Bearings: Precision bronze
- Maximum Inlet Pressure: 25 PSI
- Maximum Differential Pressure: 100 PSI
- Maximum Discharge Pressure: 100 PSI
- Relief Valve: None fitted
- Viscosity Range: 40 to 10,000 SSU
- Condition: New
Frequently Asked Questions
Q: Can it run at the full 10,000 SSU viscosity?
Yes, but not at full speed. Heavy stock needs the pump slowed down, and the required suction head roughly doubles at the top of the viscosity range compared with a thin oil.
Q: Does the pump self prime?
It will prime on its own once the internals are wetted, but the ports should face upward on installation so air can clear. If nothing is discharged after about sixty seconds, stop and find out why rather than letting it run.
Q: Is a motor or a mounting foot included?
No. This is a bare pump end. Mounting feet are listed separately by pump size, and C face adapters are published across the NEMA range from 56C up to 326TC.
Q: What is the difference between the B and the F builds?
The B build uses a mechanical seal and carries the higher pressure ratings, up to 250 PSI inlet and 300 PSI discharge. The F build uses a spring loaded lip seal and is limited to 25 PSI inlet and 100 PSI discharge.
Not sure this is the right part? Send us a Picture of the Pump Plate on your pump and the CLR Marine team will confirm the correct pump end.
CLRMarine
