Flotec FP4832 Shallow Well Jet Pump — 1HP Stainless Steel Model FP4832
Getting reliable water pressure from a shallow well shouldn't mean fighting rust, weak flow, or a pump that wears out after a couple of seasons. The Flotec FP4832 was built with that frustration in mind. Its stainless steel housing shrugs off corrosion far better than standard cast iron or thermoplastic alternatives, which means homeowners can count on steady performance year after year, even in properties where water quality or humidity would normally shorten a pump's lifespan.
This 1HP model is designed specifically for shallow well setups, delivering strong output at depths to water of 25 feet or less, with a maximum pumping capacity that reaches into the high teens of gallons per minute. That's more than enough to keep a household running smoothly, whether it's supplying a kitchen faucet, a shower, an irrigation line, or a full home plumbing system during peak demand. The motor arrives ready to run on 230 volts out of the box, with straightforward instructions available for converting to 115 volts if that better fits an existing electrical setup.
Beyond raw power, what makes the FP4832 a practical long-term choice is how little fuss it demands. It's built for continuous, non-stop operation without needing constant attention, and the heavy-duty construction is meant to handle the kind of daily use a well pump sees without complaint. For anyone replacing an aging, corroded pump or setting up a new shallow well system, this is a dependable, no-nonsense option that prioritizes durability as much as performance.
Key Features
- Heavy-duty stainless steel pump housing for superior corrosion resistance
- Delivers strong performance at well depths to water of 25 feet or less
- Maximum pumping capacity up to 18.4 GPM
- Ready-to-install 230 volt motor, convertible to 115 volt
- Engineered for efficient, non-stop residential operation
- Pressure switch pre-set for consistent household water pressure
Applications
- Residential shallow well water supply systems
- Homes needing consistent pressure for plumbing fixtures
- Replacement pump for aging or corroded shallow well units
- Light agricultural or garden irrigation water delivery
- Cabins, rural properties, and homes relying on private well water
Specifications
- Horsepower: 1 HP
- Body Construction: Stainless steel
- Maximum Capacity: Up to 18.4 GPM
- Flow at 10 ft Lift and 40 PSI: Approximately 14.6 GPM
- Maximum Lift: 25 ft
- Maximum Pressure: 58 PSI
- Pressure Switch Setting: 30 PSI on / 50 PSI off
- Suction Port Size: 1-1/4" NPT
- Discharge Port Size: 1" NPT
- Voltage: 230V / 115V, 60Hz
- Amp Draw (Full Load): 9.6A at 230V / 19.2A at 115V
- Recommended Breaker: 15A at 230V / 25A at 115V
- Maximum Water Temperature: 122°F (50°C)
- Warranty: 1 year limited
FAQ
Q: Can the Flotec FP4832 be used with a deep well instead of a shallow well?
This pump is engineered specifically for shallow well applications with a lift of 25 feet or less, so it is not intended for deep well use, which typically requires a different jet kit configuration.
Q: Does the FP4832 come pre-wired for 115 volts?
No, it ships ready to run on 230 volts, but it can be converted to 115 volts by following the wiring instructions in the included manual.
Q: Is a pressure tank required to run this pump?
Yes, like most jet pumps, the FP4832 is designed to work with a pressure tank to maintain consistent water pressure throughout the plumbing system.
Q: How noisy is this pump during operation?
It runs at a typical level for a residential jet pump of this size, and noise can often be reduced further by installing it on a vibration-dampening pad or mounting bracket.
Q: What kind of maintenance does the FP4832 need over time?
Routine maintenance is minimal, generally limited to periodic checks of the pressure switch, motor connections, and suction line for leaks, since the stainless steel housing resists the corrosion that causes many pump failures.
CLRMarine
