Flotec FP4432 Vertical Deep Well Jet Pump: Reliable 1 HP Performance
If you're pulling water from a deep well and need a pump that can actually keep up with the depth, the Flotec FP4432 is built for exactly that job. It's a vertical, multi-stage jet pump designed for wells where the water table sits well below the surface, and it's rated to work in 4-inch or larger wells down to 260 feet, or 2-inch wells down to 180 feet. The cast iron housing gives it the kind of rugged, long-term durability that matters when a pump is expected to run season after season without giving you trouble.
What sets this pump apart from a standard shallow well unit is how it handles depth. Once your water source drops past 25 feet or so, a simple pump starts to lose efficiency, but the FP4432's multi-stage design is made for that scenario, delivering up to 12 GPM and staying efficient even at lifts of 50 feet or more. It ships ready to run on 230 volts, with the option to convert to 115 volts using the included manual instructions, so it can adapt to whatever electrical setup your well house has.
Homeowners and property owners dealing with a genuinely deep well often find that off-the-shelf shallow well pumps just aren't up to the task. The FP4432 fills that gap, offering the flow and lift capability needed for household water supply, irrigation support, or backup water systems without requiring a submersible pump installation. It's a straightforward, dependable option for anyone who wants strong performance from a pump they can service and maintain at the surface rather than pulling it out of the ground.
Key Features
- Vertical, multi-stage jet pump design for deep well applications
- Rugged, heavy-duty cast iron pump housing for long service life
- Superior performance at depths to water of 50 feet or more
- Ready-to-install 230 volt motor, with 115 volt conversion available per manual
- Preset 40/60 psi pressure switch
- Silicone carbide shaft seal for added durability
- 1 year limited warranty
Applications
- Primary water supply for homes served by a deep well
- 4-inch diameter or larger wells up to 260 feet deep
- 2-inch diameter wells up to 180 feet deep
- Rural and agricultural water supply systems
- Backup or supplemental well water pumping
- Residential water pressure systems requiring high lift capability
Specifications
- Model Number: FP4432 (FP4432-01)
- Horsepower: 1 HP
- Maximum Capacity: 12 GPM
- Flow at 50 ft lift and 40 psi: 11 GPM
- Maximum Lift: 260 ft (4" or larger well) / 180 ft (2" well)
- Voltage: 230V / 115V, 60 Hz
- Amp Draw (full load): 9.6 amps at 230V / 19.2 amps at 115V
- Recommended Breaker: 15 amp (230V) / 20 amp (115V)
- Suction Pipe Size: 1-1/4" NPT
- Drive Pipe Size: 1" NPT
- Discharge Pipe Size: 1" NPT
- Pressure Switch Setting: 40/60 psi
- Body Construction: Cast iron
- Shaft Seal: Silicone carbide
- Maximum Water Temperature: 140°F (60°C)
FAQ
Q: How deep can the Flotec FP4432 pull water from?
A: It's rated for 4-inch diameter or larger wells up to 260 feet deep, and 2-inch diameter wells up to 180 feet deep.
Q: Does the FP4432 come with a pressure tank?
A: No, this is the pump unit only. It includes a preset 40/60 psi pressure switch, but a separate pressure tank is needed for a complete system.
Q: Can this pump run on 115 volts instead of 230 volts?
A: Yes, it ships ready to run on 230 volts, and can be converted to 115 volt operation by following the wiring instructions in the included manual.
Q: What size pipe fittings does the FP4432 use?
A: It has a 1-1/4" NPT suction pipe connection, a 1" NPT drive pipe connection, and a 1" NPT discharge connection.
Q: Is a jet ejector kit included with the pump?
A: No, the jet kit is typically sold separately and should be matched to your specific well depth and casing size.
CLRMarine
