Safety Duplex Cable - 18/2 AWG - Red/Yellow - Flat - 250' Ancor safety duplex cable features red and yellow Marine Grade primary conductors (correctly color-coded to ABYC standards) in a white common jacket that is made for easy removal while providing the best abrasion resistance available. These cables exceed UL 1426 standards and are made from the highest quality ultra flexible (Type 3/Class K) tinned copper stranding that provides maximum protection against corrosion and electrolysis while resisting fatigue due to vibration and flexing. The premium vinyl insulation is rated at 600V, 105°C dry and 75°C wet, stays flexible even in extreme cold (-40°F/C) and resists salt water, battery acid, oil, gasoline, heat, abrasion and ultra-violet radiation. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Safety Duplex Cable - 18/2 AWG - Red/Yellow - Flat - 500' Ancor safety duplex cable features red and yellow Marine Grade primary conductors (correctly color-coded to ABYC standards) in a white common jacket that is made for easy removal while providing the best abrasion resistance available. These cables exceed UL 1426 standards and are made from the highest quality ultra flexible (Type 3/Class K) tinned copper stranding that provides maximum protection against corrosion and electrolysis while resisting fatigue due to vibration and flexing. The premium vinyl insulation is rated at 600V, 105°C dry and 75°C wet, stays flexible even in extreme cold (-40°F/C) and resists salt water, battery acid, oil, gasoline, heat, abrasion and ultra-violet radiation. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Safety Duplex Cable - 18/2 AWG - Red/Yellow - Flat - 1,000' Ancor safety duplex cable features red and yellow Marine Grade primary conductors (correctly color-coded to ABYC standards) in a white common jacket that is made for easy removal while providing the best abrasion resistance available. These cables exceed UL 1426 standards and are made from the highest quality ultra flexible (Type 3/Class K) tinned copper stranding that provides maximum protection against corrosion and electrolysis while resisting fatigue due to vibration and flexing. The premium vinyl insulation is rated at 600V, 105°C dry and 75°C wet, stays flexible even in extreme cold (-40°F/C) and resists salt water, battery acid, oil, gasoline, heat, abrasion and ultra-violet radiation. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stow 'n Go Dock Box - Deep Small - 46"L x 26"W x 27"H With a UV gelcoat finish and the stainless steel lockable latch and hardware these are built tough. Our dock boxes incorporate gas shock lifts, which come standard on all models. These shocks help to keep your lid open on rocking docks and in higher wind areas and allows for a slower, more controlled closing. These fiberglass molded dock boxes are also constructed with a smooth interior finish which helps prevent splinters in your hands when storing or retrieving your boating accessories. Features: 46"L x 26"W x 27"H Heavy duty stainless steel lockable latch and hinges Gas shocks come standard on all models

Hand Bilge Pump 18" x 24" These Manual Bilge Pumps are designed for use in small boats without electrical power or for larger boats in emergencies where power is no longer available. Compact, lightweight, and easy to stow. Foot valve is removable for easy cleaning. Capacities from 6-13 GPM. Pumps feature removable hoses and storage clips. To prevent leaks, hose must be screwed in, NOT pushed in. Constructed of durable UV resistant injection molded nylon.

18" x 14" Heavy Duty Performance Trim Tab Kit w/o Switch Kit -12V Lenco Electric Heavy Duty Polished Blade Trim Tab Kits are supplied with electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges, 85 degree inside taper and 1/4" diameter hinge pin. Kits equipped with Extreme Duty actuators with 5/16" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. . Kit Contents: 2 each of 12-gauge stainless steel Electro-Polished trim tab blades  2 each of #15055-001 XD extreme duty actuators with 6' lead and Deutsch plugs 2 each of #30133-103  20' actuator extension wiring harnesses 1 each of the Lenco owner’s / installation manual Boat-mounting hardware supplied by customer Specifications: Suggested Boat Length: 22' to 42' Length of Tab: 18" Width of Tab: 14" Minimum Transom Height: 10.5" Blades: 12 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Switch Required: 15069-001 or 15070-001 Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

18" x 14" Standard Performance Trim Tab Kit w/o Switch Kit- 12V Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades Kit Contents: 2 each of 12-gauge stainless steel Electro-Polished trim tab blades 2 each of #15054-001 actuators with 6' lead and Deutsch plugs 2 each of #30133-103 20' actuator extension wiring harnesses 2 each of #15085-001 (#116) upper mounting bracket with gland seal    2 each of #50014-001 (#119) lower mounting bracket  1 each of the Lenco owner’s / installation manual All necessary stainless steel mounting hardware Specifications: Suggested Boat Length: 22' to 40' Length of Tab: 18" Width of Tab: 14" Minimum Transom Height: 11" Blades: 12 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

18" x 12" High Performance Trim Tab Kit w/o Switch Kit-12V - Single Actuator Lenco HP Single & Dual Actuator Electric Trim Tab Kits feature electro-polished 7 Gauge 304SS Blades & Sacrificial Anodes. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Each kit is factory assembled with extreme duty actuators with 3/8" SS bolts, a full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes. Kit Contents: 2 each of stainless steel trim tab planes 2 each of #15056-001 XD extreme duty actuators with 6' lead & Deutsch plugs Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes. The following to be supplied by customer: Boat mounting hardware supplied by customer Actuator extension harnesses (2 for single actuator application or 4 for dual) will be required. To order the lengths of your choice see the Lenco Accessories Section. Specifications: Suggested Boat Length: 20' to 40' Length of Tab: 18" Width of Tab: 12" Minimum Transom Height: 10.5" Blades: 7 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Switch Required: 10222-211D, 15069-001 or 15070-001  Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Super Dynaplate f/SSB Radio - 18" x 6" x 1/2" Create a proper bonding and grounding system using Dynaplate grounding shoes to reduce the risk of serious hull damage and electrical shock associated with boat lightning strikes by providing a direct, controlled high-capacity path for lightning dissipation. SSB and AM radio transmitters rely upon a proper size ground to operate to their designed capacity. A Dynaplate grounding shoe helps provide a large solid surface (the water surrounding the boat) to "push off" from. This is technically known as "counterpoise" and is the other necessary half of the antenna system. The bronze Dynaplate material also serves as the next sacrificial metal on the galvanic scale after the zincs, providing another buffer against corrosion of stainless steel parts. Features: Easy to clean with wire brush Conforms to ABYC standards Mounting hardware included Gold plated mounting bolt Bronze mounting nuts Copper washers WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Black Pinfish Rectangular Trap - 18" x 12" x 8" Features: Heavy-duty vinyl dipped steel mesh Black color offers camouflage Easy access door on rectangular traps Adjustable entry on flat bottom trap 1264-Saltwater Safe

Bait Quarters 18" x 18" - 20 Gallons A handy natural container for bait or for storing your game fish. Tie a Bait Quarters to a dock or boat slip and keep any fish healthy for extended periods. The cleverly designed buoyant top keeps the lid handy for easy access. Weighted bottom maintains a cylindrical shape even in stiff currents. A Velcro latch keeps pesky birds out. The soft 3/8 white nylon mesh is strong enough to keep fish yet gentler than traditional wire or metal boxes. Made from non-corrosive materials for a lifetime of fresh or saltwater use. Collapses for easy storage. Check state regulations for use guidelines. Features: Convenient Usage - floating design provides easy access off a boat or at the pier 3/8 Soft Nylon Mesh - fish friendly will not rough up fish like wire mesh cages or metal boxes Non-Corrosive Materials - ideal for fresh or salt-water use Velcro Latch Lid - keeps pesky birds out - and bait or game fish in Convenient Storage - collapses for easy storage

F-10 Twin Eye Fender 18" x 50" - White Polyform has been producing the F Series fender for over 50 years and there is no comparison when it comes to quality, range of sizes, and protection offered.   The F Series fender has offered protection to the world's finest yachts and fishing vessels.  Why?  Because the owners and captains of these prestigious boats know that they can rely on Polyform’s F Series fenders to offer the size, strength, and dependability to protect their vessels from the rigors of the sea and weather. If you want the ultimate protection for your boat, Polyform F Series fenders are the only choice!  Classic European twin-eye style boat fenders for the most discerning eye. Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced ropeholds Designed for use by trailered boats and in permanent protected moorings Twin-eye design for vertical or horizontal use Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 18" x 50" (45.7 x 127cm) Eye Diameter - 1" (2.54cm) Circumference - 56.6" (143.7cm) Volume - 33.8 gallons (154.4L) Boat Size - 60' - 70' (18.3 - 21.3M) Weight - 19.95lbs *Sold as an Individual

F-10 Twin Eye Fender 18" x 50" - Black Polyform has been producing the F Series fender for over 50 years and there is no comparison when it comes to quality, range of sizes, and protection offered.   The F Series fender has offered protection to the world's finest yachts and fishing vessels.  Why?  Because the owners and captains of these prestigious boats know that they can rely on Polyform’s F Series fenders to offer the size, strength, and dependability to protect their vessels from the rigors of the sea and weather. If you want the ultimate protection for your boat, Polyform F Series fenders are the only choice!  Classic European twin-eye style boat fenders for the most discerning eye. Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced ropeholds Designed for use by trailered boats and in permanent protected moorings Twin-eye design for vertical or horizontal use Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 18" x 50" (45.7 x 127cm) Eye Diameter - 1" (2.54cm) Circumference - 56.6" (143.7cm) Volume - 33.8 gallons (154.4L) Boat Size - 60' - 70' (18.3 - 21.3M) Weight - 19.95lbs *Sold as an Individual

D-Vec Boat Bag - Large - 18" x 12" x 12" - Grey/Blue  From top to bottom, Daiwa’s Boat Bag is meticulously designed and constructed of only the best materials. Beginning with the outer material, the Boat Bag features an incredibly durable and waterproof marine-grade vinyl. Not water-resistant, but waterproof. The marine quality, the double-zippered top is further protected by a storm flap, enhancing the Boat Bag’s ability to repel water. Below, you’ll appreciate the non-slip, thick EVA padded bottom. The padding adds cushioning for more delicate items like a camera or smartphone.  Size: 18" x 12" x 12"

F-10 Twin Eye Fender 18" x 50" - Blue Polyform has been producing the F Series fender for over 50 years and there is no comparison when it comes to quality, range of sizes, and protection offered.   The F Series fender has offered protection to the world's finest yachts and fishing vessels.  Why?  Because the owners and captains of these prestigious boats know that they can rely on Polyform’s F Series fenders to offer the size, strength, and dependability to protect their vessels from the rigors of the sea and weather. If you want the ultimate protection for your boat, Polyform F Series fenders are the only choice!  Classic European twin-eye style boat fenders for the most discerning eye. Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced ropeholds Designed for use by trailered boats and in permanent protected moorings Twin-eye design for vertical or horizontal use Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 18" x 50" (45.7 x 127cm) Eye Diameter - 1" (2.54cm) Circumference - 56.6" (143.7cm) Volume - 33.8 gallons (154.4L) Boat Size - 60' - 70' (18.3 - 21.3M) Weight - 19.95lbs *Sold as an Individual