Flojet 21004-205 Kit Diaphragm Bun Pp/5 Cam  

LUTZ 0110-205 Drum Pump Tube Lutz Drum and Container Pump MSL-PP-41-L-HC-39" for non-flammable liquids Lutz Drum Pumps model MSL-PP 41 is for use with acids and alkalis Applications: The robust Lutz pump tube with mechanical seal or sealless is suitable for pumping clean and dirty, thin-bodied and slightly viscous, aggressive and non-aggressive liquids out of drums and small or large containers. The pump tube is non-lubricated, thus preventing contamination of the liquids pumped.   Liquid examples: Acids, alkalis, galvanic fluids, phosphates, nitrates, sulphates, chlorates, etc.   Lutz Multipurpose Sealless Polypropylene Pump Tube Bearing Housing: ETFE / PTFE Drive Shaft: HC-4 (2.4610) Stainless Steel (316 Ti)< Impeller Code: Radial-Flow Impeller Impeller Material: PP Length: 39" Tube Housing: Polypropylene Tube Type: MSL-PP

LUTZ 0122-205, Drum Pump Tube FEATURES Pump Body:Kynar PVDF, 39 Inch Tube Impeller:ETFE Shaft:Hastelloy C Shaft Seal:The drive shaft of this pump tube is not sealed. The bearing housing unit behind the impeller is designed to prevent pumped liquid from rising between the shaft and the inner tube. APPLICATIONS Lutz pump tubes are immersible centrifugal pumps.  The drive shaft of this pump tube is not sealed.  The bearing housing unit behind the impeller is designed to prevent pumped liquid from rising between the shaft and the inner tube.  This device guides the liquid which penetrates between the drive shaft and the shaft bearing back into the container being drained. Features:  • Suitable for highly corrosive chemicals and neutral liquids in non-explosive areas  • Optional with electric or air driven motors  • No grease fillings  • Optimized drum drainage  • Modular, service friendly design    Applications:  The robust Lutz pump tube with mechanical seal or sealless is suitable for pumping clean and dirty, thin-bodied and slightly viscous, aggressive and non-aggressive liquids out of drums and small or large containers. The pump tube is non-lubricated, thus preventing contamination of the liquids pumped.    Liquid examples: Highly concentrated acids and alkalis, bromic acid, sulphuric acid, nitric acid, dimethyle phthalate, potassium bromate, hydrofluoric acid, etc.

Gianneschi SGM45 Brush GM4 7X14 (Cp25/1)

Gianneschi SGM45A Brushes For CP25/1

Flojet G57-5205 Pump Air 4.5/100 Santo 3/8 The Flojet G57-5205 Diaphragm Air Pump AOD is Air Powered and uses a 3/8” Hose Barb Snap-In Ports. The G57-5205 discharges 4.5GPM Max, Polypropylene, Santoprene Check Valve Seat and Diaphragm, 1/4” Hose Barb Straight Brass Air Inlet   Model No.: G57 Series Capable of Air or CO2 drive pressures up to 100PSI (6.9bar) Highest flow rate for any air pump of comparable size Robust Design with durable integral mounting Patented Shuttle Valve, eliminates stalling Capable of passing solids up to 3.2mm diameter easily with large clog-free Check Valves Corrosion Resistant materials capable of handling a wide range of chemicals Sanitary design with insert molded diaphragm (Santroprene only) Leak Resistant radial seals, no critical o-ring seals Quiet Operation with large exhaust muffler Ease of Installation with all quick disconnect ports Stall-proof design with patented shuttle valve   Automotive Cleaning and Recycling; Chemical Transfer and dispensing; Bag-In-Box chemicalsParts Washers; Car Wash Systems   Innovative compact design features a patented shuttle valve that eliminates stalling and provides a long life. Features a chemically resistant polypropylene body with a choice of EP/PP blend, FKM or FFKM elastomers, as well as quick disconnect liquid and gas port fittings for easy installation.

Hypro 9910-620561, Gasket   Replacement for: 9910-D115/9910-D115GR34/9910-D135 Models

Yanmar X0520505-01 Mechanical Seal

SEAWORTHY Prospec Electronics manufactures some of the world's best-known marine audio products such as SeaWorthy. A leader in the marine aftermarket, Prospec has grown to become known internationally exporting products to clients throughout the world. The innovative SeaWorthy line is so successful, within one year Prospec focused exclusively on the marine industry.

Aktivator-205 Clear 250ml Bottle Sika® Aktivator-205 is a solvent-based colorless clear adhesion promoter, which reacts with moisture and deposits active groups on the substrate. These groups act as a link between substrates and primers or sealants/adhesives. Sika® Aktivator-205 is designed for the treatment of bond faces prior to the application of Sikaflex® and Sikasil® adhesives and sealants.    Features: Enhanced adhesion on various substrates Short flash-off time Easy to use Transparent Areas of Application: Sika® Aktivator-205 is used to improve adhesion on non-porous substrates such as metals, plastics, ceramic screen prints, and painted surfaces. Seek manufacturer’s advice and perform tests on original substrates before using Sika® Aktivator-205 on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.

Handlebar Mount for Edge® 205, 305, 605 & 705 Secure your Edge® to the handlebar of your bike with this bike mount. Zip ties included. Compatible Devices: Edge® 205, 305, 605 & 705 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Turning Point Hub Kit: 205 Features Lifetime Warranty Never buy another hub kit system again Inner splines adapt to the engine Outer hub compatible with different props Reduce gear shock & engine/drive damage Save up to 30% when purchasing a replacement prop Eliminate propeller vibration & chatter Eliminate hub cracking & failure Corrosion resistant materials - brass splines Reduce gear shock & engine/drive damage WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

GP2050-10 SailPod Pre-Cut for Simrad NSE8 or B&G Zeus Z8 for 12" Wide Guard GP2050 Series for 12" Guard, SailPods for Sail are for mounting a single radar or chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. A single SailPod is best mounted on a Single Bend AngleGuards or use a Double Bend AngleGuards to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications. Sizing: Overall Size: 10.875"H x 15.125"W x 6.75"D Usable Face: 8.75"H x 12.75"W x 5"D Max Cutout: 8.375"H x 12.375"W All SailPods include Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners and wrench Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

GP2050-11 SailPod Pre-Cut for Garmin 8008/8208 for 12" Wide Guard GP2050 Series for 12" Guard, SailPods for Sail are for mounting a single radar or chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. A single SailPod is best mounted on a Single Bend AngleGuards or use a Double Bend AngleGuards to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications. Sizing: Overall Size: 10.875"H x 15.125"W x 6.75"D Usable Face: 8.75"H x 12.75"W x 5"D Max Cutout: 8.375"H x 12.375"W All SailPods include Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners and wrench Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets

GP2050-12 SailPod Pre-Cut for Garmin 820/82xs/840xs for 12" Wide Guard GP2050 Series for 12" Guard, SailPods for Sail are for mounting a single radar or chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. A single SailPod is best mounted on a Single Bend AngleGuards or use a Double Bend AngleGuards to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications. Sizing: Overall Size: 10.875"H x 15.125"W x 6.75"D Usable Face: 8.75"H x 12.75"W x 5"D Max Cutout: 8.375"H x 12.375"W All SailPods include Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners and wrench Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets