14-M360-2DDI-Y - MEGA 360 & 2D/MDI 14-Pin Y-Cable This Y cable allows for the connection of a MEGA 360 Imaging transducer and a 14-pin HW / MDI+ transducer (including Built-in MEGA Imaging) to the same compatible Humminbird fish finder.  Combines MEGA 360 Imaging transducer and 14-pin Dual Spectrum / MEGA Imaging+ transducers (including Built-in MEGA Imaging) into one 14-pin plug for connection to the same, compatible SOLIX fish finder, or HELIX fish finder with additional AD HELIX M360 adapter. For use when connecting a MEGA 360 Imaging transducer to a compatible SOLIX or HELIX fish finder, in conjunction with a Built-in MEGA Imaging transducer or external 14-pin HW /MDI+ transducer. If this cable is being used with a HELIX fish finder, then the #720106-1 AD HELIX M360 adapter must be attached between this y-cable and the HELIX unit, to the single plug end of the Y cable. Compatible with Built-in MEGA Imaging transducers on select Minn Kota trolling motors 30" (76 cm) cable on Dual Sprectrum CHIRP side of cable 10' (3 m) cable on the MEGA 360 side Waterproof, screw-on, 14-pin connectors 1-Year Limited Warranty

Y-Valve The Jabsco Y-Valve is designed to provide flexibility of onboard waste management by diverting waste either into an onboard holding tank or directly overboard where legal to do so. Check local and Federal regulations to determine where direct overboard discharge of untreated waste is permitted. No overboard discharge of untreated waste is allowed within three miles of shore. Some near shore areas and inland areas are designated as "No-Discharge Zones" where the discharge of any onboard waste, even treated waste is strictly prohibited. Many of these areas require a waste retention system that can be positively secured in an onboard retention mode. The Jabsco Y- Valve accommodates this requirement by providing the ability to add a padlock that secures the selector handle in either direction to ensure waste is directed to an onboard holding tank. The Y-Valve may also be used to direct waste from a holding tank to an onboard waste discharge pump for holding tank evacuation or, alternatively, to a waste deck plate for removal by a shoreside pump-out facility. The Y- Valve may also be used in a bilge pumping system to select between two separate bilge pickups in different bilge compartments providing for evacuation of two separate bilge areas with only one bilge pump. Features: Chemical and corrosion resistant polypropylene and stainless steel construction Selector lever can be padlocked (lock not included) and/or sealed in either position Ports can be rotated so discharge plumbing can be routed away in parallel, at 900 or in opposite directions, or either up or down without disassembly Valve is supplied with both 1-1/2" (38 mm) ports (fitted) and extra 1" (25 mm) straight inlet port Optional shaft extension allows valve to be mounted through a bulkhead up to 1-3/4" thick with only the selector handle exposed Self cleaning design provides trouble free operation Molded in flow direction indicator arrows Easy access to three sturdy mounting feet for quick and simple installation Easy access to valve by removal of just three hex head machine screws, top cover and diverter assembly lift away from the body WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

9-M360-2-DDI-Y - MEGA 360 & 2D/MDI 7-Pin Y-Cable This Y cable allows for the connection a MEGA 360 Imaging transducer and an external 7-pin HW / MDI+ transducer to the same compatible HELIX fish finder.  Combines MEGA 360 Imaging transducer and 7-pin Dual Spectrum/MEGA Imaging+ transducers into one 7-pin transducer plug for connection to the same, compatible HELIX fish finder. For use when connecting a MEGA 360 Imaging transducer to a HELIX fish finder, in conjunction with an external 7-pin HW / MDI+ transducer. This cable should not be use to connect a HELIX fish finder with both MEGA 360 Imaging and Built-In MEGA Imaging on Minn Kota trolling motors. Please refer to #720108-1 14 M360 2DDI Y for this specific rigging need. Is not compatible with Built-in MEGA Imaging transducers on select Minn Kota trolling motors 30" (76 cm) cable on Dual Sprectrum CHIRP side of cable 10' (3 m) cable on the MEGA 360 side 1-Year Limited Warranty

Reverse "Y" Adapter The Reverse "Y" Adapter has two male plugs with special power isolation circuitry for added safety. When one plug is connected to a receptacle, the circuitry isolates the second plug. The reverse "Y" provides 50A 125/250V power when only two 30A 125V receptacles are available. Note: Reverse "Y" will NOT work with 50A, 125V, 3-wire inlets. Power is provided in both circuits to the 4-wire inlet, but the dock side receptacles limit the current in each circuit to 30A. The two 30A 125V receptacles must be supplied from a single power source providing from 208V to 250V between them for proper operation. Boat Side: Female Connector 50A 125/250V w/Sealing Collar System Attaches to boat inlet or cordset Dock Side: Male Plug 2-30A 125V Locking Attaches to dockside receptacle or cordset WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

14 M SILR Y - SOLIX®/APEX® Side Imaging Left-Right Splitter Cable  The 14 M ID SILR Y cable allows for two Side Imaging transducers to be connected to into a single sonar input on a Humminbird chartplotter. This y-cable utilizes the two Side Imaging transducer to act as independent port and starboard Side Imaging sonar sources when boat hulls and transducer obstructions require separate transducers for a clear picture on each side of the vessel. This rigging cable provides the ability to install a separate high-speed Humminbird 2D transducer for high-speed depth reading and sonar performance. Alternatively, this cable can also be used to add an accessory Airmar® 2D transducer to a Humminbird control head that also has a Side or Down Imaging transducer connected at the same time. This cable supports Transducer ID for automatic recognition and easy setup of Airmar® accessory transducers. Features: Compatible with: All SOLIX and APEX models Combines two Side Imaging transducers together, acting as independent port and starboard Side Imaging sonar sources and can then be connected to a single Humminbird control head. Includes transducer ID for Airmar® accessory transducers when used in combination with 14 M ID SIDB Y (#720111-1) Cable length: 30" (76 cm) 1-Year Limited Warranty

Diverter Y Valve with Fittings Raritan’s Diverter Y-Valve allows for easy installation as it can be configured using any port as input. Port connections are National Pipe Thread allowing the use of the many stock fittings available in local marine and hardware stores. The flexibility of configuring each port with a different fitting allows the installer to easily connect to hoses without having to run new lines or change runs just to enable the connection. The body is constructed of ABS and allows a full flow of water through the valve body. This full-flow design helps to eliminate some of the common problems caused by a restriction in the line created by Y-valves. The valves do allow re-configuration of which ports are open or closed in the event the valve must be rotated a certain way for proper installation. In addition, Raritan supplies labels to place on the mounting straps so that the port is clearly labeled as to where the flow is directed. To satisfy No Discharge regulations the valve must be directed to a holding tank while in a No Discharge Zone and the handle removed. The handle easily detaches by simply lifting it up. Features: Full flow Diverter Y Valve The valve body is constructed of durable, high-strength ABS Any port can be easily configured as an Input All female ports are standard 1 ½ National Pipe Thread (NPT) A removable handle helps satisfy No Discharge Zone requirements Mounting clamps are included for easy bulkhead mounting Labels included for clear port identification WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

RealVision 3D™ Bronze Thru-Hull Transducer Pair Pack - 12° - 8M Cable & Y-Cable Designed for inboard or outboard boats, the RV-212 Bronze Through Hull Transducer System lets you easily identify structures and locate fish with the life-like clarity of RealVision 3D™ sonar. The RV-212 system is a 4-channel, Wide Spectrum CHIRP transducer system with DownVision™, SideVision™, high frequency CHIRP fish targeting and RealVision 3D™ sonar inside. The transducer system has a built-in attitude and heading reference system (AHRS) that stabilizes the sonar imagery, automatically compensating for vessel motion. You’ll enjoy crystal-clear imagery in waves, swells, and while maneuvering. The RV-212 system also has a built-in fast response water temperature sensor for quick, accurate readings. Raymarine’s RV-212 Bronze Through Hull Transducer system pack contains a pair of RealVision 3D transducers with internal offset to accommodate hull deadrise angles from 1° to 12°. This completely eliminates the need for fairing blocks. The low-profile design slips effortlessly through the water without causing drag or cavitation. The near-flush RV-212 system works great on trailered boats too. The RV-212 system features rugged cast-bronze through hull bodies suitable for fiberglass or wooden hulls. One transducer transmits and receives to port and downwards, the other to starboard and downwards, ensuring a full 180° of underwater coverage even on boats with deep keels or other underwater protrusions. Each transducer features a 2M pigtail, joining y-cable and 8-meter extension cable, resulting in an overall cable length of 10M (33'.) What’s in the Box? RV-212P Bronze Port Transducer with 2M cable RV-212S Bronze Starboard Transducer with 2M cable RealVision 3D Transducer Y-Cable RealVision 3D 8M (26') Transducer Extension Cable Anti-rotation bolt kit Installation instructions

RealVision 3D™ Bronze Thru-Hull Transducer Pair Pack - 20° - 8M Cable & Y-Cable Designed for inboard or outboard boats, the RV-220 Bronze Through Hull Transducer System lets you easily identify structures and locate fish with the life-like clarity of RealVision 3D™ sonar. The RV-220 system is a 4-channel, Wide Spectrum CHIRP transducer system with DownVision™, SideVision™, high frequency CHIRP fish targeting and RealVision 3D™ sonar inside. The transducer system has a built-in attitude and heading reference system (AHRS) that stabilizes the sonar imagery, automatically compensating for vessel motion. You’ll enjoy crystal-clear imagery in waves, swells, and while maneuvering. The RV-220 system also has a built-in fast response water temperature sensor for quick, accurate readings. Raymarine’s RV-220 Bronze Through Hull Transducer system pack contains a pair of RealVision 3D transducers with internal offset to accommodate hull deadrise angles from 13° to 20°. This completely eliminates the need for fairing blocks. The low-profile design slips effortlessly through the water without causing drag or cavitation. The near-flush RV-220 system works great on trailered boats too. The RV-220 system features rugged cast-bronze through hull bodies suitable for fiberglass or wooden hulls. One transducer transmits and receives to port and downwards, the other to starboard and downwards, ensuring a full 180° of underwater coverage even on boats with deep keels or other underwater protrusions. Each transducer features a 2M pigtail, joining y-cable and 8-meter extension cable, resulting in an overall cable length of 10M (33'.) What’s in the Box? RV-220P Bronze Port Transducer with 2M cable RV-220S Bronze Starboard Transducer with 2M cable RealVision 3D Transducer Y-Cable RealVision 3D 8M (26') Transducer Extension Cable Anti-rotation bolt kit Installation instructions

9 M SILR Y Dual Side Image Transducer Adapter Cable f/HELIX  Y Cable - Separates Side Imaging into Left and Right Side Beams - for Side Imaging products only.  Allows the use of two side imaging transducers with one unit without the need for a transducer switch.  Y Cable - Separates Side Imaging into Left and Right Side Beams - for Side Imaging products only.  Allows the use of two side imaging transducers with one unit without the need for a transducer switch.  Used in applications where the a plastic thru the hull transducer is required on a boat with a deep V hull or the motor or other items on the transom of the boat may block one side of the transducer and distort readings.    30" length. Supports MEGA Side Imaging. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Garmin 12-Pin Transducer Y-Cable Port/Starboard - 10m Connect a port/starboard pair of thru hull or transom mount transducers to the sonar unit with this 12-pin Y-cable. This cable allows the use of two different transducers to produce the left and right SideVü images to avoid engine lower unit or keel/hull shadowing. The right-side (starboard) transducer is used for Traditional, ClearVü, and right- SideVü images plus water temperature and transducer ID. The left-side (port) transducer is used for left-SideVü images. Compatible with all 12-pin GT transducers. Connect a port/Starboard pair of thru-hull transducers to the sonar unit with this 12-pin Y-cable. The cable is approximately 10 meters (32.81 ft) long. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

14 M ID SIDB Y - SOLIX®/APEX® Side Imaging & 2D Splitter Cable  The 14 M ID SIDB Y cable allows for the installation of a separate 2D transducer paired with a Humminbird MEGA Imaging or non-MEGA Imaging transducer and connect both transducers to a single Humminbird control head. This y-cable provides the ability to install a separate high-speed Humminbird 2D transducer for high-speed depth reading and sonar performance. Alternatively, this cable can also be used to add an accessory Airmar® 2D transducer to a Humminbird control head that also has a Side or Down Imaging transducer connected at the same time. This cable supports Transducer ID for automatic recognition and easy setup of Airmar® accessory transducers. Features: Compatible with: All SOLIX and APEX models Combines a MEGA Side Imaging transducer (or non-MEGA Imaging) and accessory 2D transducer and allows them to be connected to a single Humminbird control head. Automatically provides Side Imaging, Down Imaging and temperature from the standard all-in-one transducer and sources 2D sonar and digital depth from the 2D accessory transducer, without the need to switch data sources manually Includes Transducer ID for Airmar® accessory transducers, which automatically recognizes transducer type for easy installation and setup. Cable length: 30" (76 cm) 1-Year Limited Warranty

V10 Series RCA Audio Y Cable - 2 Channel - 1 Female to 2 Males T-Spec's Y cable will send your musical signals cleanly across the veritable battlefield of induced noise and uncertain factory electronics in your vehicle, so you'll enjoy all of your music with none of the noise.  T-Spec RCA cables resist noise due to their shielded construction and the double twisted pair arrangement of the wire inside their jackets. Recycled copper often contains impurities that can impair a wire's conductivity, so T-Spec uses only oxygen-free non-recycled, virgin copper to maximize signal flow in their patch cables.  Each machined metal RCA plug features a patented 4-way split tip that guarantees the best possible electrical contact.  T-Spec's proprietary PVC jacket gives each cable great flexibility for easier installation, and the durability required for marine certification. Features: Double twisted-pair design minimizes noise from your system Oxygen-free virgin copper Split-tip RCA connectors for maximum contact area Ultra-flexible PVC blended jacket Marine compliant In the Box: 1 10" RCA Audio Y cable - 1 Female to 2 Males Instruction sheet *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

V10 Series RCA Audio Y Cable - 2 Channel - 1 Male to 2 Females T-Spec's Y cable will send your musical signals cleanly across the veritable battlefield of induced noise and uncertain factory electronics in your vehicle, so you'll enjoy all of your music with none of the noise.  T-Spec RCA cables resist noise due to their shielded construction and the double twisted pair arrangement of the wire inside their jackets. Recycled copper often contains impurities that can impair a wire's conductivity, so T-Spec uses only oxygen-free non-recycled, virgin copper to maximize signal flow in their patch cables.  Each machined metal RCA plug features a patented 4-way split tip that guarantees the best possible electrical contact.  T-Spec's proprietary PVC jacket gives each cable great flexibility for easier installation, and the durability required for marine certification. Features: Double twisted-pair design minimizes noise from your system Oxygen-free virgin copper Split-tip RCA connectors for maximum contact area Ultra-flexible PVC blended jacket Marine compliant In the Box: 1 10" RCA Audio Y cable - 1 Male to 2 Females Instruction sheet *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Manufacturers that start with the letter Y  

Bosworth 94 Y-Valve W/O Internal Thread   Bosworth Y-Valve Sea-Lect Gray Delrin In-Line 1” Smooth Hose Ports