Micropump S/K CA-I.SFS 81052 For Ca-I.Sfs.0

Micropump CA-I-SFS.A Pump Head A Mount

Micropump CA-I.SFS-DEMSE Pump Head/Eagle Drive

Manufacturers that start with the letter I  

Ulterra 80/MSI/IP Trolling Motor w/i-Pilot Link & Bluetooth - 24v-80LB - 60" Only Ulterra™ features Auto Stow/Deploy and Power Trim, as well as your choice of i-Pilot® or i-Pilot Link™, and a multi-function foot pedal. You can stow, deploy and trim Ulterra from the remote or the foot pedal, meaning you never have to touch your motor again — unless you want to high-five it. Now with Built-In MEGA Side and Down Imaging™ Sonar.  Auto Stow & Deploy: Stow or deploy Ulterra just by pushing a button on your i-Pilot or i-Pilot Link remote, foot pedal or Humminbird fish finder. Power Trim: Trim Ulterra up or down at the push of a button — on either the foot pedal, the i-Pilot or i-Pilot Link remote or a Humminbird fish finder. Adjust to changing fishing conditions without reaching down to your trolling motor. i-Pilot® Link™ Integrated GPS Trolling System: i-Pilot® Link™ gives you unprecedented control over your boat by linking your trolling motor to your Humminbird® fish finder. Control your trolling motor from Link's color touch-screen remote or the Humminbird. You can set Spot-Locks, record paths, follow depth contours, automatically navigate to your favorite spots, control speed and steering, and more. Spot-Lock with Jog: Spot-Lock will hold you in place with unparalleled GPS accuracy. Available on i-Pilot GPS system that is pre-installed, Spot-Lock gives you the power to stay right on top of any productive fishing spot, without touching your trolling motor. With the included heading sensor, you can use Jog to move your Spot-Lock location five feet in any direction. Activate Spot-Lock from the i-Pilot remote or Humminbird fish finder. AutoPilot™: Automatically navigate your boat in any direction you choose. Just point the head of your trolling motor in the direction you want to travel, activate AutoPilot™, and your trolling motor will keep you on that heading automatically, even correcting for wind, waves and current. Built-In MEGA Side and Down Imaging®:  With a transducer built right into the trolling motor, you get crystal clear Humminbird® MEGA Side Imaging and MEGA Down Imaging with a clean look and protected housing. Heel-Toe Electric Foot Pedal: Stow, deploy and adjust the trim on Ulterra — all from the foot pedal. You can even activate Spot-Lock with one tap. Includes 18' cord. Integrated Battery Meter: The i-Pilot remote can tell you the exact charge left in your trolling batteries, so you know how much time you have left on the water. Digital Maximizer™: Provides up to 5 times longer run time on a single battery charge. These variable speed trolling motors let you dial in your exact speed, and they deliver only as much power as you need, helping to conserve your battery for a full day of fishing. Weedless Wedge™ 2 Prop: With swept-back flared blades to power through anything without battery-draining chopping and hacking, the Weedless Wedge™ 2 is one of the most trusted props in fishing. Indestructible Composite Shaft — Guaranteed for Life: At the core of your Minn Kota trolling motor is an indestructible composite shaft. It's a Minn Kota exclusive, and we guarantee it for life. Mobile App Compatibility: Control i-Pilot directly from your Apple® or Android™ device with our mobile app. You get quick command of speed, steering, Spot-Lock and Advanced AutoPilot — plus the ability to update i-Pilot software. What's included: Ulterra 80 lb. 60" motor with Built-In MEGA Side and Down Imaging i-Pilot Link Remote Remote Charging Cable USB DC Adapter Lanyard, Heading Sensor 30' Ethernet Extension Cable Corded Foot Pedal MKP-33 Prop Mounting Hardware.

i-Pilot Replacement Remote - Legacy The updated i-Pilot includes additional recording capacity and a new remote with improved functionality and enhanced durability. The most significant enhancement to i-Pilot is the updated remote. The LCD screen and function icons are 20% larger and the keypad has improved visibility, durability, and tactile feel. The remote has a slimmer, more ergonomic design as well as an easy-access battery compartment. The i-Pilot is capable of storing a total of six Spot-Lock and six Record A Track locations compared to three locations each on the original version. Available for select saltwater and freshwater models, the new i-Pilot can be purchased already installed on select Minn Kota Terrova™, PowerDrive V2™, Riptide® ST or Riptide SP bow-mount trolling motors, or as an accessory. The remote can be purchased separately for use with the original i-Pilot systems but will not include the additional storage space. The following are the key features of i-Pilot: Spot-Lock works like an electronic anchor, holding the boat in place. If the boat drifts more than five feet from the Spot-Lock location, i-Pilot will activate the trolling motor to keep the angler on the designated spot. It automatically corrects for wind, waves, current and drift. The "recall" feature for Spot-Lock provides the ability to return to that specific location at a later time. Up to six Spot-Lock locations can be stored at a time. Record A Track allows an entire fishing track, up to a remarkable two miles in length, to be stored to memory (up to six separate tracks). When you want to retrace a course in either direction, i-Pilot's playback functions will automatically guide your boat along the track. Cruise Control maintains real-time on-the-water boat speed in one-tenth mile-per-hour increments. This precise speed control allows the angler to dial in bait presentations in trolling applications. Advanced AutoPilot™ utilizes GPS technology to maintain the boat path on a true heading while adjusting for wind, waves, current and side-drift. This results in improved and more accurate tracking compared to traditional compass-based systems. CoPilot™ is Minn Kota's wireless trolling motor control system and is integrated into the i-Pilot remote control. Anglers can control speed and steering from anywhere in the boat. ** Compatible with non-Bluetooth i-Pilot systems that have been manufactured in 2016 or earlier.  ** * Battery Included. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

i-Pilot System Remote Access w/Bluetooth NOTHING COMES REMOTELY CLOSE. The same i-Pilot that lets you lock onto a fishing spot, record and retrace paths, and command speed and steering just got better. Redesigned with a larger LCD screen, more options, and better controls, we've dialed in the technology that lets you dial in your boat position. Redesigned Remote We gave it a 33% larger LCD screen that's fully viewable in sunlight, expanded menu navigation, and more intuitive controls - making the i-Pilot remote better than ever. Bluetooth Communication The new i-Pilot system connects via Bluetooth, allowing for easy software updates to add new features to your system via your smartphone. i-Pilot Phone App Bluetooth communication allows new i-Pilot to pair with your smartphone, allowing for easy software updates and quick command of speed, steering, Spot-Lock, high speed bypass, and Advanced AutoPilot. Heading Sensor Select i-Pilot systems feature a new Heading Sensor, which recognizes changes in the boat's heading due to wind andcurrent, and communicates with the i-Pilot system to minimize boat swing for a more accurate, stronger hold. Reinvented Spot-Lock Enhanced with new hardware and software algorithms, Spot-Lock works holds you tighter to your fishing spot than ever before, making it the most accurate electronic GPS anchor ever. Spot-Lock Jog Move your Spot-Lock five feet forward, backward, left or right - just by pushing a button. Additional Features: iTrack Record/Playback: Store and retrace up to six 2-mile trolling paths to return to later Advanced AutoPilot: Stay on a heading automatically Cruise Control: Precisely dial in and adjust speed in 0.1 mile-per-hour increments CoPilot: Control and monitor speed, steering, prop on/off and high speed bypass *The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Johnson Outdoors, Inc. is under license. Other trademarks and trade names are those of their respective owners. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

i-Pilot Link Wirless Remote w/Bluetooth *Charging Cable sold Seperatly* NOW WE'RE REALLY TALKING. Redesigned with new features, a new remote, and Bluetooth connectivity, the new i-Pilot Link system communicates better than ever before to give you even more control of your trolling motor from your Humminbird or i-Pilot Link remote. Redesigned Remote A more compact remote with a bigger, full-color touchscreen featuring a fully-customizable menu. A keypad with commonly used navigation functions gives you the best of both worlds. Bluetooth Communication: The new i-Pilot system connects via Bluetooth, allowing for easy software updates to add new features to your system via your smartphone. i-Pilot Link Phone App Bluetooth communication allows new i-Pilot to pair with your smartphone, allowing for easy software updates and quick command of speed, steering, Spot-Lock, high speed bypass, and Advanced AutoPilot Heading Sensor A Heading Sensor recognizes changes in the boat's heading due to wind and current, and communicates with the i-Pilot Link system to minimize boat swing. Reinvented Spot-Lock Enhanced with new hardware and software algorithms, Spot-Lock works holds you tighter to your fishing spot than ever before, making it the most accurate electronic GPS anchor ever. Spot-Lock Jog Move your Spot-Lock five feet forward, backward, left or right - just by pushing a button. Circle Mode Cast to a spot while orbiting in a circle around it with Circle Mode. Just choose the spot and how far from it you want to be, and your boat will circle the spot while you drop the hammer. Humminbird Virtual Remote Control speed, steering, Spot-Lock, and Advanced AutoPilot, directly from a new virtual remote on the Humminbird screen. Additional Features: Cruise Control CoPilot iTrack Record/Playback BackTrack Advanced AutoPilot Follow the Contour Contour Offset GoTo Compatibility: i-Pilot Link is available pre-installed on: Ultrex™ Ulterra™ / Riptide® Ulterra™ Terrova® / Riptide® Terrova® The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Johnson Outdoors, Inc. is under license. Other trademarks and trade names are those of their respective owners. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

60" Post Guide-On with I-Beam Mounting Kit & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 60" Post Guide-Ons With I-Beam Mounting Kits and two Camo Wet Lands Post Guide-On Pads. These Post Guide-Ons allow you to see the location of your trailer when it's underwater. Designed for I-beam trailers and I-beam boat lifts, these guide-ons feature an innovative two-piece mounting clamp that works above or below the I-beam. Brackets will fit onto any height and virtually any width I-beam trailer frame. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware included Adjusts out to 19" on each side 1-1/2" square. 16 gauge pre-galvanized steel uprights 2-3/8" diameter white PVC posts Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post-guide-on covers: Camo Wet Lands Kit Includes: Part 27648: C.E. Smith 60" Post Guide-On With I-Beam Mounting Kit  Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

Terrova 112/MDI/IP Trolling Motor with i-Pilot Link & Bluetooth - 36V-112lb-60" Now with built-in MEGA-DI: You can’t mark fish if you can’t see fish. And the best view of what’s below comes from Humminbird’s  MEGA Imaging™. So get a Humminbird’s eye view with a MEGA DI transducer built right into the lower unit of our most powerful, trusted motors. No cluttered wires, no clamps, and a transducer that’s protected from the elements. Just plug your fish finder into your motor to see what’s down there. Then go catch it.  No External Transducer - Messy wiring on an externally mounted transducer doesn’t just look bad: the transducer and wires are more susceptible to damage. With Built-In MEGA DI, the transducer is housed in the indestructible lower unit and all wiring runs through the shaft, for a clean, uncluttered look that’s protected from the elements. Humminbird MEGA Imaging opened the eyes of anglers everywhere by taking fish finding into the megahertz frequency for the first time. Now your Minn Kota® motor can deliver crystal clear MEGA Down Imaging of what’s directly below the bow, just the way it was meant to be seen.  In addition to MEGA Down Imaging, the Built-In MEGA DI transducer will also provide a CHIRP Digital Sonar, for precise, crystal-clear returns of fish, structure, and the bottom at all water levels. Sweeping multiple frequencies across a broad spectrum, this powerful tool eliminates noise for precisely defined targets.  Features: Lift-Assist Design:  A spring-loaded assembly on the Terrova mount makes stowing the trolling motor effortless, every time. Stow/Deploy Lever:  Press this lever on the mount and fallaway ramps will effortlessly slide your trolling motor into the water. And when you're ready to move, Lift-Assist helps the motor stow effortlessly. i-Pilot® Link™ Integrated GPS Trolling System:  i-Pilot® Link™ gives you unprecedented control over your boat by linking your trolling motor to your Humminbird® fish finder. Control your trolling motor from Link's color touch-screen remote or the Humminbird. You can set Spot-Locks, record paths, follow depth contours, automatically navigate to your favorite spots, control speed and steering, and more. Spot-Lock with Jog:  Spot-Lock will hold you in place with unparalleled GPS accuracy. Available on the i-Pilot GPS that is pre-installed, Spot-Lock gives you the power to stay right on top of any productive fishing spot, without touching your trolling motor. With the included heading sensor, you can use Jog to move your Spot-Lock location five feet in any direction. Activate Spot-Lock from the i-Pilot remote or Humminbird fish finder. AutoPilot™: Automatically navigate your boat in any direction you choose. Just point the head of your trolling motor in the direction you want to travel, activate AutoPilot™, and your trolling motor will keep you on that heading automatically, even correcting for wind, waves, and current. Heel-Toe Electric Foot Pedal:  Stow, deploy and adjust the trim on Terrova - all from the foot pedal. You can even activate Spot-Lock with one tap. Includes 18' cord. Push-to-Test Battery Meter:  Press a button on the trolling motor head to get an instant status of the battery life you have left. Digital Maximizer™:  Provides up to 5 times longer run time on a single battery charge. These variable-speed trolling motors let you dial in your exact speed, and they deliver only as much power as you need, helping to conserve your battery for a full day of fishing. Weedless Wedge™ 2 Prop:  With swept-back flared blades to power through anything without battery-draining chopping and hacking, the Weedless Wedge™ 2 is one of the most trusted props in fishing. Indestructible Composite Shaft - Guaranteed for Life:  At the core of your Minn Kota trolling motor is an indestructible composite shaft. It's a Minn Kota exclusive, and we guarantee it for life. Mobile App Compatibility:  Control i-Pilot directly from your Apple® or Android™ device with our mobile app. You get quick command of speed, steering, Spot-Lock, and Advanced AutoPilot — plus the ability to update i-Pilot software.

Heading Sensor for BlueTooth i-Pilot This Bluetooth-enabled heading sensor contains a compass that detects your boat's heading and communicates it to your trolling motor to enable the Spot-Lock Jog feature, which lets you move your Spot-Lock 5' increments in any direction.   Available as an add-on accessory for PowerDrive and Riptide PowerDrive trolling motors that come pre-installed with Bluetooth i-Pilot systems (model year 2017 and after). This heading sensor comes standard with updated Ultrex, Ulterra, Terrova, Riptide Ulterra and Riptide Terrova trolling motors that come pre-installed with Bluetooth i-Pilot and i-Pilot Link systems. (model year 2017 and after). HEADING SENSOR ONLY.  Compatible with Bluetooth-enabled i-Pilot systems only. This remote will only work with i-Pilot systems that are equipped with Bluetooth.  It is NOT compatible with systems that do not use Bluetooth. Refer to original remote or product manual that came with trolling motor to ensure system compatibility. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Skylla-i Battery Charger 24/100 (3) 230V Battery Charger The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Features: Rugged - Aluminium epoxy powder-coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible - Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Please refer to the manual for a complete overview of the possibilities.  Synchronized parallel operation - Several chargers can be synchronized with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP cables. Note: Two output and three output chargers cannot be paralleled with each other. Please see the manual for details. The right amount of charge for a lead-acid battery: variable absorption time - When only shallow discharges occur the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. Preventing damage due to excessive gassing: BatterySafe mode - If to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-i will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use: Storage mode - The storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode float voltage is reduced to 2.2V/cell (26.4V for 24V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. To increase battery life: temperature compensation - Every Skylla-i comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations in battery temperature are expected. Battery voltage sense - To compensate for voltage loss due to cable resistance, the Skylla-i is provided with a voltage sense facility so that the battery always receives the correct charge voltage. Suitable for AC and DC supply (AC-DC and DC-DC operation) - The chargers also accept a DC supply. Use as a power supply - As a result of the perfectly stabilized output voltage, the Skylla-i can be used as a power supply if batteries or large buffer capacitors are not available. Li-Ion (LiFePO4) ready - Simple charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the galvanically isolated CAN bus port. Specifications: Input voltage (VAC): 230V Input voltage range (VAC): 185-265V Input voltage range (VDC): 180-350V Maximum AC input current @ 180 VAC: 20A Frequency (Hz): 45-65Hz Charge voltage 'absorption' (VDC): 28.8V Charge voltage 'float' (VDC): 27.6V Charge voltage ‘storage’ (VDC): 26.4V Charge current (A): 3 x 100A (max total output: 100A) Charge algorithm: 7-stage adaptive Battery capacity: 500-1000Ah Charge algorithm (LiFePO4): 3 stages, with on-off control or CAN bus control Temperature sensor: Yes Power supply mode: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) VE.Can communication port: Two RJ45 connectors, NMEA2000 protocol, galvanically isolated. Integrated 12V CAN-bus power supply, 30V DC maximum Synchronized parallel operation: Yes, with VE.Can Forced cooling: Yes Protection: Battery reverse polarity (fuse) / Output short circuit / Over temperature Operating temp. range: -20 to 60°C (Full output current up to 40°C) Material & Colour: aluminium (blue RAL 5012) Battery connection: M8 bolts 230 VAC-connection: screw-clamp 10mm² (AWG 7) Protection category: IP21 Weight: 16 lbs. (7 kg) Dimensions (hxwxd): 405 x 250 x 150 in (16.0 x 9.9 x 5.9mm) Please contact your dealer for any returns, repairs or support issues related to this product.

Discover Boating, the recreational boating industry's national awareness campaign, is holding an amateur video and photo contest called i-Discovered Boating to showcase Americans' love of the boating lifestyle.   Boaters across the U.S. are encouraged to submit videos and photos illustrating how they discovered boating for a chance to win up to $10,000 and to have their creation featured in a national advertising campaign for Discover Boating. Entries can be submitted at DiscoverBoating.com beginning May 25. All entries must be received by June 30. Winners will be unveiled July 15 on DiscoverBoating.com. "Every boater has a personal story on why they take to the water, whether it's a favorite family pastime, stress relief from the life on land or just the feeling of wind in their hair. It's these personal experiences that drive an estimated 70 million Americans to go boating each year," said Carl Blackwell, spokesman for Discover Boating, in a statement. "We hope to spread this passion for the boating lifestyle by providing a forum for boaters to share their unique perspective of how they discovered boating," he added.

60" Post Guide-On With I-Beam Mounting Kit Product Description These Post Guide-Ons allow you to see the location of your trailer when it's under water. Designed for I-beam trailers and I-beam boat lifts, these guide-ons feature an innovative two-piece mounting clamp that works above or below the I-beam. Brackets will fit onto any height and virtually any width I-beam trailer frame. Features: Mounting hardware included Adjusts out to 19" each side 1-1/2" square. 16 gauge pre-galvanized steel uprights 2-3/8" diameter white PVC posts Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) *Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

75" Post Guide-on These extra tall Post Guide-Ons allow you to see the location of your trailer when it's under water. Designed for I-beam trailers and I-beam boat lifts, these guide-ons feature an innovative two-piece mounting clamp that works above or below the I-beam. Fits on I-beams up to 4" wide with provided hardware. Features: Mounting hardware included Sold in pairs Adjusts out to 19" on each side Fits frames up to 3"W x 5-1/4" H 1-1/2" square, 16 gauge pre-galvanized steel uprights, 36" high 2-3/8" diameter white PVC posts WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.