RAM Composite Handlebar Swivel Base The RAM high strength composite rail mount consists of a locking tooth system with a standard diamond plate end. The mount will accommodate rails up to 1" in diameter. The hole pattern found on the diamond base adapter will connect to most RAM cradles. Installation Instructions: To mount to a circular rail, simple press the plastic "U" clamp around the rail and then connect and tighten the small nut and bolt to close the U clamp. Next connect the diamond plate to the mounted clamp at the required angle and screw in the other bolt through the diamond plate. Now you are ready to connect any of the RAM composite or any other cradle with two holes positioned 1.912" center to center. Placing a rubber lining (not included) between the tube and the mount for a tube with a diameter less than 1" will help the base grab the rail. Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag. You cannot rotate the diamond plate on the U clamp when the cradle is connected.

RAM® Torque™ 3/4" - 1" Diameter Handlebar/Rail Base with 1" Ball, Medium Arm and X-Grip® for Larger Phones Take your mobile entertainment on the road with the new RAM® Torque™ handlebar and rail mounting base. We’ve paired a B-sized 1” rubber ball base that accommodates bars 3/4” – 1” in diameter with a B-sized standard length arm the dynamic X-Grip® for larger phones. Sizing inserts are included to provide a snug fit and offer additional protection for the rail. The mount utilizes nylon-insert locknuts to prevent loosening in high vibration environments. This low-profile mount is the perfect way to secure your personal electronics and small accessories in any high-vibration environment. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size. Mounting Base Dimensions: Accommodates rails 3/4" to 1" in diameter Cradle Dimensions Minimum Width = 1.75" (Minimum Height = 5.5") Maximum Width = 4.5" (Minimum Height = 3.25") Depth = 0.875" Features: 1. Rustproof 2. High strength composite and stainless steel construction 3. Spring loaded cradle expands and contracts for perfect fit of your device 4. Rubber coated tips will hold device firm and stable 5. Socket technology allows for multiple adjustment angles and articulation of device 6. Includes Tether for open cockpit and extreme environments 7. Lifetime warranty 8. Made in U.S.A. Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Ball Size: 1" Rubber Ball "B" Size 

RAM® Torque™ 3/4" - 1" Diameter Handlebar/Rail Base with 1" Ball, Medium Arm & X-Grip® for Phones Take your mobile entertainment on the road with the new RAM® Torque™ handlebar and rail mounting base. We’ve paired a B-sized 1” rubber ball base that accommodates bars 3/4" - 1" in diameter with the dynamic X-Grip® for phones. Sizing inserts are included to provide a snug fit and offer additional protection for the rail. The mount utilizes nylon-insert locknuts to prevent loosening in high vibration environments. This low-profile mount is the perfect way to secure your personal electronics and small accessories in any high-vibration environment. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size. Mounting Base Dimensions: Accommodates rails 3/4" to 1" in diameter Cradle Dimensions Minimum Width = 1.875" (Minimum Height = 4.25") Maximum Width = 3.25" (Minimum Height = 2.25") Depth = 0.875" Features: 1. Rustproof 2. High strength composite and stainless steel construction 3. Spring loaded cradle expands and contracts for perfect fit of your device 4. Rubber coated tips will hold device firm and stable 5. Socket technology allows for multiple adjustment angles and articulation of device 6. Includes Tether for open cockpit and extreme environments 7. Lifetime warranty 8. Made in U.S.A. Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Ball Size: 1" Rubber Ball "B" Size 

RAM Mount Universal X-Grip™ Holder Handlebar Rail Mount Part #: RAM-B-149Z-UN7U The RAM-B-149Z-UN7U consists of a double socket arm, handlebar rail mount with zinc coated u-bolt base and universal spring loaded X-Grip™ holder for cell phones. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at the both ends of the socket arm; this with a twist of the arm knob, allows you can move the suction cup X-Grip™ mount to your optimum viewing position. The spring loaded X-Grip™ holder expands and contracts, allowing for a perfect custom fit of your cell phone. Sometimes, its all about the design. If you are looking for a compact mount for your cell phone without that cookie cutter shape, you've found it. The RAM X-Gripȁ has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The perfect compliment to the modern sleek interior of today's vehicles, the RAM X-Grip™ is the cell phone holder evolved. Compatible and interchangeable with a wide range of popular RAM Mounting products, this elegant holder is ready to compliment your phone and become the most useful accessory in your vehicle. Compatible Devices: Apple iPhone 4S WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 4 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3G WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone (1st Generation) Apple iPod touch (All Models) Apple iPod (G1-G5) Samsung Galaxy S7 Samsung Galaxy S7 Edge All devices that maintain the following dimensions below: Holder Dimensions: Minimum Width = 0.875" (Devices at 0.875" must be a minimum of 4" in height to fit into holder) Maximum Width = 3.25" Depth = 0.875" Features: 1. Spring loaded holder expands and contracts for perfect fit of your device 2. Rubber coated tips will hold device firm and stable 3. Versatility of holder allows for attachment to many RAM-to-RAM ball mounts 4. Single socket technology allows for multiple adjustment angles and articulation of device Material: High Strength Composite, Rubber Tips & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM® Torque™ 3/4" - 1" Diameter Handlebar/Rail Base with 1" Ball, Short Arm and X-Grip® for Phones We’ve paired a B-sized 1” rubber ball base that accommodates bars 3/4" - 1" in diameter with the dynamic X-Grip®. Sizing inserts are included to provide a snug fit and offer additional protection for the rail. The mount utilizes nylon-insert locknuts to prevent loosening in high vibration environments. This low-profile mount is the perfect way to secure your personal electronics and small accessories in any high-vibration environment. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size. Mounting Base Dimensions: Accommodates rails 3/4" to 1" in diameter Cradle Dimensions Minimum Width = 1.875" (Minimum Height = 4.25") Maximum Width = 3.25" (Minimum Height = 2.25") Depth = 0.875" Features: 1. Rustproof 2. High strength composite and stainless steel construction 3. Spring loaded cradle expands and contracts for perfect fit of your device 4. Rubber coated tips will hold device firm and stable 5. Socket technology allows for multiple adjustment angles and articulation of device 6. Includes Tether for open cockpit and extreme environments 7. Lifetime warranty 8. Made in U.S.A. Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Ball Size: 1" Rubber Ball "B" Size 

RAM® Torque™ 3/4" - 1" Diameter Handlebar/Rail Base with 1" Ball, Medium Arm and Diamond Ball Base Take your mobile entertainment on the road with the new RAM® Torque™ handlebar and rail mounting base. We’ve paired a B-sized 1" ball base that accommodate bars 3/4" to 1" in diameter with a B-sized standard length arm and diamond base so that you can connect any of the RAM Mounts cradles or anything else with the AMPS hole pattern. Sizing inserts are included to provide a snug fit and offer additional protection for the rail. The mount utilizes nylon-insert locknuts to prevent loosening in high vibration environments. This low-profile mount is the perfect way to secure your personal electronics and small accessories in any high-vibration environment. Mounting Base Dimensions: Accommodates rails 3/4" to 1" in diameter  Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size 

RAM® Torque™ 3/4" - 1" Diameter Handlebar/Rail Base with 1" Ball, SHORT Arm and Diamond Plate Take your mobile entertainment on the road with the new RAM® Torque™ handlebar and rail mounting base. We’ve paired a B-sized 1" ball base that accommodate bars 3/4" to 1" in diameter with a B-sized short length arm and diamond base so that you can connect any of the RAM Mounts cradles or anything else with the AMPS hole pattern. Sizing inserts are included to provide a snug fit and offer additional protection for the rail. The mount utilizes nylon-insert locknuts to prevent loosening in high vibration environments. This low-profile mount is the perfect way to secure your personal electronics and small accessories in any high-vibration environment. Mounting Base Dimensions: Accommodates rails 3/4" to 1" in diameter  Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size 

RAM® Torque™ 3/4" - 1" Diameter Handlebar/Rail Base with 1" Ball, SHORT Arm and Level Cup™ Take your drink on the road with the new RAM® Torque™ handlebar and rail mounting base. We’ve paired a B-sized 1" ball base that accommodate bars 3/4" to 1" in diameter with a B-sized short length arm and Level Cup™ Drink Holder & Koozie. Mounting Base Dimensions: Accommodates rails 3/4" to 1" in diameter  Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size 

RAM® Torque™ 3/4" - 1" Diameter Handlebar/Rail Base with 1" Ball, SHORT Arm and GoPro®/Action Camera Mount The RAM® Torque™ handlebar and rail mounting base has a 1” rubber ball and accommodates bars 3/4” to 1” in diameter. Sizing inserts are included to provide a snug fit and protection of the rail. The mount utilizes nylon-insert locknuts to prevent loosening in high vibration environments. Included is a short double socket arm and a GoPro/Action Camera mount. Mounting Base Dimensions: Accommodates rails 3/4" to 1" in diameter  Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size 

Ram Mounts Looking for all the Ram Mount products we carry them. You can find them all right here in our Ram Mount Store Aqua Box Mount section. With everything from camera mounts to vehicle mounts including cell phone mounts, you will have plenty of choices to consider and options to choose from. Ram Mounting Systems is a quality manufacturer of all kinds of different mounts for your watercraft. You can get cell phone mounts and drink cup mounts here, along with GPS mounts and fishing rod holders. There are even iPad/iPhone/iPod mounts so you do not have to worry about having your electronics safe but close at hand.   If you have a kayak we have kayak mounts, too, and you can even do some work or surf the internet with laptop mounts to choose from. Of course, you want to make sure you choose a good marine electronics mount for your equipment, so you do not risk losing anything vital. Tablet mounts, swing arm mounts, surface mounts, and suction cup mounts are all available, and we have seat mounts, as well. You can even choose from motorcycle mounts, and rail/handle bar mounts to ensure you have everything you need your all of your future adventures.

1.5" Ball "Rugged Use" Mount f/Garmin echo 200, 500c, & 550c The RAP-101U-G4 consists of a 2.5" diameter round base with the universal AMPS hole pattern, double socket arm and round adapter base that attaches directly to the back of the Garmin echo. Designed into the mount is a 1.5" diameter patented rubber ball and socket system with adjustment points at both socket ends of the arm; this with RAM's rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. Included is hardware that is used to attach the Garmin echo to the RAM Mount. Material: High Strength Composite Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Seat Tough-Wedge Accessory with 1" Ball Base The Tough-Wedge™ is a seat wedge mount that fits in the gap between the vehicle seat and center console; allowing easy access and operation of your mobile device. The Tough-Wedge™ can also be used for back-seat applications, inserted into the pockets located on the back of the front seats. For capturing video on the go, place the Tough-Wedge™ in your backpack with a RAM camera mount. The included diamond adapter contains the industry standard AMPS hole pattern that allows attachment to a variety of RAM mounts. Hardware included to attach the Tough-Wedge™ to the mount. The 1" diamond ball base is compatible with all RAM-B size single and double socket arms. Tough-Wedge™ Dimensions: Length: 13.25" Height: 8.25" Depth: 1" Inside Wedge Depth: 0.375" - 0.875"

B Size 1" Composite Fishfinder Mount for the Lowrance Hook2 Series Designed for light duty salt water use, this B size (1”) composite drill-down kit for the Lowrance Hook² allows users to swap out the factory mounting solution with a RAM® Mounts solution. Simply attach the included adapter to the Lowrance Hook² and you’re ready to connect the double socket arm and round base featuring the AMPS hole pattern. Made of high strength composite and powder coated marine grade aluminum, this kit is designed to keep your Hook² secure and stable in rugged environments on your kayak or inflatable. Material: High Strength Composite and Marine Grade Aluminum Ball Size: 1" Rubber "B" Ball Size

Power-Grip™ XL Universal Scanner Gun Holder The RAM® Power-Grip™ XL universal scanner gun holder is designed for use with several large form factor scanner guns and is RAM® Mounts Compatible™ with a full range of ball and socket forklift mounting systems. Using high-strength composite materials, the RAM® Power-Grip™ XL secures scanner guns even when not in use. When required, easily remove the scanner gun to quickly scan the desired item. This holder features two attachment points. First, the hole pattern on the back of the holder allows for the connection of the RAM-202U or the RAM-D-254U (hardware is included for these attachments). Second, the hole pattern on the bottom of the holder allows for the connection of a 2” x 3” plate – RAM-202U-23 or RAM-D-202U-23 – or a drill-down mount (hardware is not included for these attachments). To enable use on the go, integrated holes on both sides of the holder allow for the use of a lanyard or the GDS® Shoulder Strap. Elastomeric fins grip the handle of the scanner gun to ensure a secure fit, and can be easily replaced if required.  Internal Dimensions: Width = 3.96" Length = 2.66" Depth = 7.43" Features: Unique open bottom design enables scanning while in the holder Replaceable elastomeric fins grip the handle of the scanner tight to ensure the most secure fit, and can be easily replaced if required Form fitted cradle supports and protects device without vibration High strength materials ensure product longevity Integrated lanyard holes Lifetime warranty (excludes fin grips) Included: RAM® Power-Grip XL™ Holder Hardware for attaching to compatible RAM® Mounts Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag. The holder includes a four of two nuts and bolts to connect to any compatible RAM mounts. 

Swivel Base Rod Holders RH570XL Stainless Steel Side Mount w/ Swivel Base Extra Long This holder is 4" longer than the standard length allowing the bent butt to sit deeper in the holder thus reducing the leverage and stress on the mounting surface. Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.