Vehicle Base Ford F-150 (2004-2010)
Ford F-150 (2004-2010)
Lincoln Mark LT (2005-2010)
This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation.
Placement of Mount:
Passenger side floor board, under seat
Drilling Requirements:
No - uses existing seat bolts
Seat Configuration:
Bucket/bench
Pole:
Purchased Separately
Weight:
9.1 lbs.
Material:
Powder Coated Steel
Features:
Quick installation with no drilling needed. Rock solid construction with a lifetime warranty.
The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics.
Tough-Tray Dimensions:
Tray Depth: 10.0"
Tray Thickness: 2.125"
Tray Width (Expansion): 10" to 16"
Side Clamp Arm Height: 0.5" (min) to 1.75" (max)
Material:
High Strength Composite
The RAM RAM-VP-SW1-89, combination swing arm/tele-pole system, will connect to any RAM vehicle base without a welded female tele-pole. Included is a tele-pole with a height range from 11.5" to 17"; it can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray.
The double swing arm with rotating plate, allows you to twist and tilt the viewing angle of your laptop, tablet, UMPC, monitor, or any other connected electronic device, when mounted on your RAM Vehicle Mount. Taking the highly successful RAM Vehicle Mounts to the next level, this rotating swivel arm gives you even more viewing positions for your mounted electronic device while holding everything firmly in place. The length of the double swing arm is 12".
Material:
Powder Coated Marine Grade Aluminum
|
248.86 | |
No-Drill™ Vehicle Base f/ '10-13 Ford Transit Connect + More
Compatible Vehicles:
Ford
Transit Connect (2010-2013)
Transit Connect Wagon Premiun (2013)
Transit Connect XL Van (2013)
Transit Connect XLT Van (2013)
Transit Connect XLT Wagon (2013)
Dodge
Grand Caravan (2008-2009 2012-2016)
Grand Caravan AVP (2013)
Grand Caravan Crew (2013)
Grand Caravan RT (2013)
Grand Caravan SE (2013)
Grand Caravan SXT (2013)
RAM C/V Tradesman Van (2014-2015)
Chrysler
Town & Country (2008-2009 2012-2016)
Placement of Mount:
Passenger side, front, where seat rail frame attaches to floor board
Drilling Requirements:
No - attaches to seat studs
Seat Configuration:
Bucket
Pole:
Purchased Separately
Weight:
4.5 lbs.
Material:
Powder Coated Steel
|
47.48 | |
RAM® No-Drill™ Vehicle Base for 2019 Ford Ranger
The RAM® No-Drill™ laptop mounting base features a stabilizer foot and heavy-duty steel base custom-designed to fit the 2019 Ford Ranger perfectly. Using the passenger side seat rail bolts as attachment points, existing hardware is used to secure the mounting base in the vehicle.
Specifications:
Placement of Mount: Passenger side, in front, where seat frame meets floor board
Drilling Requirements: No. Utilizes existing vehicle mounting points and hardware
Seat Configuration: Bucket
Pole: Purchased Separately
Material: Powder Coated Steel
Features:
Custom, No-Drill™ mounting base offers lowest profile in the industry
Manufactured from high strength steel with a durable powder coat finish
If required, high quality fastening hardware is included
Mounts using existing seat bolts, no drilling required
|
54.61 | |
RAM POD I Universal No-Drill Vehicle Mount with 18" Flex Rod & Diamond Adapter Base
Part #: RAM-B-316-1-238U
The RAM POD I, No-Drill vehicle mount, consists of a 1" ball and diamond base with 18" rigid flex rod. The flex rod base is designed to connect to a vehicle seat rail bolt in cars, trucks, fleet vehicles and suvs. The flex rod can hold light to medium weight items in your vehicle safely and securely.
Material:
High Strength Composite and Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
35.32 | |
RAM POD I Universal No-Drill Vehicle Mount Connecting to No Ball Base
Part #: RAM-B-316-1U
The RAM-B-316-1U, universal RAM-POD I vehicle mount, consists of a single open socket arm, connected to a 18" long flexible rod. This RAM POD I allows you to mount a light to medium weight item in a car safely and securely.
Installation Instructions:
At right angles to the base of the flexible 18" long leg is a foot with a mounting hole. Simply place the hole into the passenger seat mounting bolt and adjust the mount to the required height with the flexible leg. The rigid flexible arm will hold everything you need safely and securely.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note: The "U" in the part number reflects product packaged in poly bag.
|
31.39 | |
POD I Universal No-Drill™ Vehicle Mount with 24" Rigid Aluminum Rod & 1.5" Diameter Ball Round Adapter Base
The RAM POD I, universal no-drill™, vehicle mount is the latest in the Mobile In-Car range from RAM. This RAM POD I allows you to mount a light to medium weight item in a car safely and securely.
Features:
Installation Instructions: At right angles to the base of the flexible 24" long leg is a foot with a mounting hole. Simply place the hole into the passenger seat mounting bolt and adjust the mount to the required height with the flexible leg. The rigid flexible arm will hold everything you need safely and securely.
Material: Powder Coated Marine Grade Aluminum
Ball Size: 1.5" Rubber Ball Size
Note: The "U" in the part number reflects product packaged in poly bag
|
55.67 | |
No-Drill™ Laptop Mount for the Ford F-250, F-350, F-450, F-550, F-650, F-750 & Excursion
This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens). The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics.
Placement of Mount:
Passenger side floor board, in front of seat
Drilling Requirements:
No - attaches to seat studs
Seat Configuration:
Bucket/Bench
Material:
High Strength Composite and Powder Coated Steel
Compatibility
Ford
F-250 (1997-2016)
F-350 (1997-2016)
F-450 (1997-2016)
F-550 (1997-2016)
F-650 (1997-2019, 2021)
F-750 (1997-2019, 2021)
Excursion (2000-2005)
|
254.30 | |
RAM Universal No-Drill RAM POD III Vehicle Mount with Double Socket Arm & 2/2.5" Round Bases (AMPs Hole Pattern)
The RAM-316-3-202U consists of the RAM POD III No-Drill vehicle base, three rigid aluminum rod legs, double socket arm and two 2.5" round bases that contain the universal AMPs hole pattern. The base of the mount connects to your seat rail without any drilling necessary. The rigid aluminum rod legs can be bent to position your device to its optimum viewing location. The mount is designed with a RAM 1.5" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The universal AMPs hole pattern found on the round base adapter will connect to many RAM cradles.
Leg Lengths:
18", 20" and 30"
Installation Instructions:
At right angles to the base of two legs are feet with mounting holes. Simply place the holes into the passenger seat mounting bolts and adjust the mount to the required height with the rigid aluminum rod legs. The third leg on the RAM POD III should also be adjusted to help support the mount. The rigid aluminum rod arms will hold everything you need safely and securely.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1.5" Rubber Ball Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
136.92 | |
RAM Mount POD III Universal No-Drill Mount w/Double Socket Arm, 2.5" Round Base & 3.625" Square Base RAM Universal No-Drill RAM POD III Vehicle Mount with Double Socket Arm, 2.5" Round Base (AMPs Hole Pattern) & 3.625" Square Base (VESA 75mm X 75mm Hole Pattern)
The RAM-316-3-2461U consists of the RAM POD III No-Drill vehicle base, 3 rigid aluminum rod legs, double socket arm, 2.5" round base that contain the universal AMPs hole pattern and 3.625" square base that contains the VESA hole pattern. The base of the mount connects to your seat rail without any drilling necessary. The rigid aluminum rod legs can be bent to position your device to its optimum viewing location. The mount is designed with a RAM 1.5" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The square base includes a 75mm X 75mm VESA hole pattern with 1.5" rubber ball positioned 0.88" from the center of one edge.
Leg Lengths:
18", 20" and 30"
Installation Instructions:
At right angles to the base of two legs are feet with mounting holes. Simply place the holes into the passenger seat mounting bolts and adjust the mount to the required height with the rigid aluminum rod legs. The third leg on the RAM POD III should also be adjusted to help support the mount. The rigid aluminum rod arms will hold everything you need safely and securely.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1.5" Rubber Ball Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
140.00 | |
RAM POD III Universal No-Drill Laptop Mount w/Tough-Tray
The RAM-316-3SW1U consists of the RAM POD III No-Drill vehicle base, three rigid aluminum rod legs, ratchet swing arm and RAM Tough-Tray. The base of the mount connects to your seat rail without any drilling necessary. The rigid aluminum rod legs can be bent to position your device to its optimum viewing location. The mount is designed with a RAM 1.5" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles.
The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, smartphones or other electronics.
Leg Lengths:
18", 20" and 30"
Installation Instructions:
At right angles to the base of two legs are feet with mounting holes. Simply place the holes into the passenger seat mounting bolts and adjust the mount to the required height with the rigid aluminum rod legs. The third leg on the RAM POD III should also be adjusted to help support the mount. The rigid aluminum rod arms will hold everything you need safely and securely.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1.5" Rubber Ball Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
197.77 | |
No-Drill™ Laptop Base for the Ford F-150 & Lincoln Mark LT
The RAM® No-Drill™ laptop mounting base features a heavy-duty steel mounting base custom designed to fit this vehicle perfectly. Using the front bench or passenger side seat rail bolts as attachment points, existing hardware is used to secure the laptop mount base in the vehicle.
Placement of Mount:
Passenger side floor board, under seat
Drilling Requirements:
No - uses existing seat bolts
Hole Pattern:
Seat Bolt Distance: 11.5" center to center
Pole:
Purchased Separately
Material:
Powder Coated Steel
Features:
Quick installation with no drilling needed. Rock solid construction with a lifetime warranty.
Compatible Vehicles:
Ford
F-150 (2004-2014)
F-150 Crew Cab (2010)
F-150 FX2/FX4 (2012-2014)
F-150 Harley Davidson (2012)
F-150 King Ranch (2012-2013)
F-150 Lariat (2012-2013)
F-150 Limited (2012-2013)
F-150 Platinum (2012-2013)
F-150 Raptor (2013)
F-150 Regular Cab (2011)
F-150 STX (2012-2013)
F-150 Super Cab (2011)
F-150 Super Crew (2011)
F-150 SVT (2013)
F-150 SVT Raptor (2012)
F-150 XL (2012-2013)
F-150 XLT (2013)
Lincoln
Mark LT (2005-2011)
Note:
If you are installing this product into a 2009-2010 F-150 with the slide out cup holder, the RAM-VB-109A is the preferred kit. The standard RAM-VB-109 kit will install but limit the use of the cup holder. To use the RAM-VB-109 with the slide out cup holder, pull the cup holder all the way out if you plan to use it prior to installation. Once installed, the cup holder will not be able to slide back under the center console. The RAM-VB-109A has an adjustable riser that can be positioned so that the cup holder is not interfered with. For base model trucks without the slide out cup holder, the standard RAM-VB-109 kit is ideal.
|
81.37 | |
RAM® No-Drill™ Vehicle Base for '20-22 Ford Police Interceptor Utility
The RAM® No-Drill™ laptop mounting base features a heavy-duty steel mounting base with a universal design to fit the 2020-2022 Ford Police Interceptor Utility. Using the passenger side seat rail bolts as attachment points, existing hardware is used to secure the mounting base in the vehicle. Compatible with RAM® Tele-Pole™ mounting systems to complete your in-vehicle solution.
Features:
RAM® No-Drill™ base offers low-profile mounting; designed specifically for the 2020-2022 Ford Police Interceptor Utility
Compatible with RAM® Tele-Pole™ mounting systems
Requires no drilling into the vehicle and installs on the passenger side using the existing seat bolts
Made of powder-coated steel
Backed by a lifetime warranty
Specifications:
Hardware Included: Foot Stabilizer
Hole Pattern: Seat Bolt Distance 12" Center to Center
Materials: Powder Coated Steel
|
40.13 | |
Vehicle Base
Compatible Vehicles:
DODGE RAM 1500-5500 (2008-2011)
This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation
Placement of Mount:
Passenger side, front, where seat rail frame attaches to floor board.
DRILLING REQUIREMENTS:
No - attaches to seat studs
Seat Configuration:
Bucket
Pole:
Purchased Separately
Weight:
2.1 lbs.
Material:
Powder Coated Steel
Dimensions:
A = 14.75", B = 3.8", C = 1.75", Hole Center = 13.25"
Features:
Quick installation with no drilling needed. Rock solid construction with lifetime warranty. Low profile keeps mount away from passenger leg space. Won?t interfere with levers or factory-installed console or 4WD lever. Designed to accommodate trucks with PTO
Swing Arm
The RAM RAM-VP-SW1-89, combination swing arm/tele-pole system, will connect to any RAM vehicle base without a welded female tele-pole. Included is a tele-pole with a height range from 11.5" to 17"; it can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray.
The double swing arm with rotating plate, allows you to twist and tilt the viewing angle of your laptop, tablet, UMPC, monitor, or any other connected electronic device, when mounted on your RAM Vehicle Mount. Taking the highly successful RAM Vehicle Mounts to the next level, this rotating swivel arm gives you even more viewing positions for your mounted electronic device while holding everything firmly in place. The length of the double swing arm is 12".
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1.5" Rubber Ball "C" Size
Note:
Part number reflects product packaged in clear clam shell for store shelf display.
Laptop Mount Tray
The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics.
Tough-Tray Dimensions:
Tray Depth: 10.0"
Tray Thickness: 2.125"
Tray Width (Expansion): 10" to 16"
Side Clamp Arm Height: 0.5" (min) to 1.75" (max)
Material:
High Strength Composite
Note:
Part number reflects product packaged in clear clam shell for store shelf display. The Tough-Tray is compatible with laptops that have 17" screens. If the Tough-Tray Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-n-Motion kit.
|
237.17 | |
Compatible Vehicles:
Ford Edge (2007-2011)
Ford Fusion (2013-2014)
This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens). The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics.
Material:
High Strength Composite and Powder Coated Steel
Notes:
If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit.
|
222.16 | |
No-Drill™ Vehicle Laptop System f/97-15 Ford Expedition
This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12" to 18". Dual swing arms provide articulation and 12" of reach for passenger and driver access to the mounted device. Rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation.
The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens). The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics.
Compatible Vehicles:
Ford Expedition (1997-2015)
Ford Expedition King Ranch EL (2013)
Ford Expedition Limited (2013)
Ford Expedition Limited EL (2013)
Ford Expedition Ranch EL (2013)
Ford Expedition XLT (2013)
Ford Expedition XLT EL (2013)
Ford F-150 (1997-2003)
Ford F-150 Heritage (2004)
Ford F-250 Light Duty (1997-2004)
Ford Windstar (2004-2007)
Specs & Features
Placement of Mount: Passenger side floor board, under seat
Drilling Requirements: No - uses existing seat bolts
Seat Configuration: Bucket/Bench
Material: High Strength Composite and Powder Coated Steel
Notes:If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit.
One 4" riser is included with this vehicle base. Step feature allows minimized amount of intrusion of passenger leg space. This base will not interfere with factory installed console in most installations.
|
266.34 | |