Submersible Pressure Transducer 0-3 PSI Maretron’s submersible pressure transducers indicate tank levels and can be installed directly in the tank. Please follow these instructions to mount and connect a submersible pressure transducer to an NMEA 2000® network via a Maretron FPM100 Fluid Pressure Monitor. Maretron recommends one of two methods for mounting a submersible pressure transducer in a tank: 1) without a restraining tube, and 2) with a restraining tube. The submersible pressure transducers are designed for a tank with a 5-hole SAE J1810 fitting at the top. Install the mounting plate with cord grip onto the transducer cable, with the rounded hex section of the cord grip facing away from the transducer. Lower the pressure transducer into the tank such that the transducer lies at the lowest point of the tank and tighten the cord grip to secure the cable. On a tank with a flat bottom, the transducer may slide from side to side with the motion of the vessel but will not rotate due to the stiffness of the cable. It is also possible to mount the pressure transducer inside a restraining or focus tube (sold separately, Maretron part number TFT-5H). Pressure Transducer Mounting Connect the two wires of the pressure transducer to a free pressure monitoring channel. Connect the red wire from the pressure transducer to the channel's positive (+) terminal and connect the black wire from the pressure transducer to the negative (-) terminal of the channel. The example in Figure 1 shows the pressure transducer connected to switch channel 0, with the white wire connected to "P0+" and the brown wire connected to "P0-." Submersible pressure transducers have a small plastic vent tube in the connecting cable. Use a Maretron DSM Series Display (firmware 1.4.7 or higher) or a PC running Maretron’s N2KAnalyzer software (version 1.4.19 or higher) to configure the connected channel(s) on the FPM100. Supply power to the NMEA 2000 network and verify that the pressure channel indicates a valid pressure reading. Specifications: Operating Range: 0 to 3 PSI (0.207 bar) Depth Range (Water): 83.1” (2.11 m) Depth Range Diesel (820 kg/m3): 101.3” (2.57 m) Depth Range Gasoline/Petrol (750 kg/m3): 110.8” (2.81 m) Cable Length: 17 ft (5.18 m) Sensor Type: Gauge (Vent Tube) Output: 4 – 20 mA current loop, loop powered Excitation Voltage: 8 VDC to 28 VDC Compatible Fluids / Gases: Diesel, Diesel Exhaust Fluid (DEF), Gasoline/Petrol, Hydraulic Fluid, Kerosene, Motor Oil, Fresh Water, Sea Water, Waste Water Operating Temperature: 14 degrees F to 158 degrees F (-10 degrees C to 80 degrees C) Storage Temperature: -4 degrees F to 176 degrees F (-20 degrees C to 80 degrees C) Accuracy: ±0.3% Full Scale typ. at 25°C Total Error Band (TEB): ±1.0% Full Scale typ. (-10 degrees C to 70 degrees C) Non-Linearity, Hysteresis (NLH): ±0.2% Full-Scale typ. Best Straight Line (BSL) at 25°C Temperature Compensation: 23 degrees F to 122 degrees F (0 degrees C to 50 degrees C) Accuracy: ±1% Full Scale Linearity: 0.5% Full Scale Repeatability: 0.05% Full Scale Full-Scale Thermal Error: 0.04% Full Scale/°F (0.07% Full Scale/degrees C) Long-Term Stability: 0.2% Full Scale/year Response Time: 150ms Proof Pressure: 2 × Full Scale Burst Pressure: 3 × Full Scale Reverse Voltage Protection: ± 30V for 3 minutes Construction: 316L stainless steel body and diaphragm, polyether polyurethane cable, chloroprene boot EMC Compatibility: 10 Volts/meter per EN 61000-4-3 Weight: 24.8oz (703g)

Submersible Pressure Transducer - 0-1.5 PSI The submersible pressure transducers are used together with Maretron's Fluid Pressure Monitor (FPM100), which allows tank fluid level to be broadcast over an NMEA 2000® network where it can be monitored from any compatible NMEA 2000® display. When used together with Maretron displays, alerts can be set to inform the user of low or high tank levels. Users can be notified through emails or text messages about their tank levels when not onboard the vessel. Additionally, the tank levels can be stored using Maretron's data recorder (VDR100) for later analysis.

Submersible Pressure Transducer - 0 to 5 PSI The submersible pressure transducers are used together with Maretron's Fluid Pressure Monitor (FPM100), whichallows tank fluid level to be broadcast over an NMEA 2000® network where it can be monitored from any compatible NMEA 2000® display. When used together with Maretron displays, alerts can be set so the user can be informed of low or high tank levels. And when not on-board the vessel, users can be notified through emails or text messages about theirtank levels. Additionally, the tank levels can be stored using Maretron's data recorder (VDR100) for later analysis. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Galley Maid Pressure Gauge 0-60 PSI Picture is a representation of a 0 to 60 PSI gage.

Pressure Transducer - 0 to 5000 PSI This pressure transducer is designed to connect to the NMEA 2000® network via a Maretron FPM100 Fluid Pressure Module. Specifications: Range: 0 to 5000 PSI (344.74 bar) Accuracy: +/- 0.5% Full Scale Type: Absolute (no vent tube) Installation: All Maretron pressure transducer assemblies are equipped with a 1/4 in. NPT male threaded fitting. Install the pressure transducer to a 1/4 in. NPT female fitting on the system or tank is to be monitored with a maximum torque of 150 in-lbs (16.95 Nm). If you are monitoring a system where pressure spikes or transients will occur, or where the pressure will exceed the maximum pressure rating of the pressure transducer, install a Pressure Snubber (PT-SNUB-01) onto the system being monitored first, then install the pressure transducer to the female port on the pressure snubber.

Pressure Transducer 0 to 50 PSI All Maretron pressure transducer assemblies are equipped with a 1/4” NPT male threaded fitting. Install the pressure transducer to a ¼” NPT female fitting on the system or tank to be monitored with a maximum torque of 150 in-lbs (16.95 Nm). If you are monitoring a system where pressure spikes or transients will occur, or where the pressure will exceed the maximum pressure rating of the pressure transducer, install a Pressure Snubber (PT-SNUB-01) onto the system being monitored first, then install the pressure transducer to the female port on the pressure snubber. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Pressure Transducer 0 to 1.5 PSI For use with FPM100 Fluid Pressure Monitor WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Pressure Transducer 0 to 5 PSI - for FPM100 Fluid Pressure Monitor WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Pressure Transducer 0 to 3 PSI - for the FPM100 Fluid Pressure Monitor WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

2" Oil Pressure Gauge (0-100 PSI) A pressure gauge operates by sending a low amperage current through the gauge's meter to ground via a sending unit with variable resistance. The resistance of the sending units increase or decrease with the changes in pressure, temperature, etc... As the sender's resistance varies, the amount of current allowed to flow through it to ground changes and the meter deflects, showing the change in pressure. Includes fire orange pointer, black aluminum bezel, flat glass lens, case with locator keyway to ensure proper installation and perimeter lighted black dial with stylish white graphics. Available for MG systems, J1939 CAN Bus or J1939 Stand-Alone systems and mechanical types. 2" - Hole Size: 2.0625" (53mm) Specifications: Standard (100-200°F) Scratch Resistant Lens Black Aluminum Bezel Orange Contoured Pointer

Jabsco 30472-1000 Pressure Gauge 0-60 Psi  

Marine Navigation & Instruments, Supplies and Equipment With a wide variety of Marine Navigation equipment and Instruments, we can help you find your location on the waterways, avoid hazards, and be respectful of other boaters. The accessories you have on your boat are important, but very few of them are as valuable as the AIS systems, autopilots, black box modules, and other options you can choose from when you want to make sure you can find your way there and back again while staying away from areas that could mean running aground or experiencing other dangers. We offer many types of navigation equipment, including cameras - network video, ice flashers, and marine monitors.   Depending on where you are going to be boating and what you plan to do with your time on the water, you can also find a fishfinder/sounder - color or a fishfinder/sounder - mono that will be right for you, along with GPS - chartplotters, GPS - fishfinder combos, or a GPS - track plotter. Network accessories and network capable displays are available, and we have a selection of night vision, software, transducers and transducer accessories, and weather fax equipment. If you need radar - stand alone options or radar domes / arrays, look no further than right here, where the selection is good and so are the prices.

i40 Bidata Display w/Thru-Hull Transducers Compact and feature-packed instruments, the i40 series instruments are smart choice for boaters looking high performance and great value. The i40 series is simple to operate thanks to the use of just three control buttons, i40 has extra-large digits and razor-sharp LCD displays and red backlighting for outstanding visibility in all lighting conditions. These SeaTalk® compatible instruments offer full integration with Raymarine autopilots and navigation equipment. The ultra-sleek design of i40 line is designed to complement our full line of a-Series, c-Series and e-Series Multifunction displays, and looks great on the helm of any boat. All i40 Instruments come with a low-profile surface mounting kit and silicone rubber sun cover. An optional bracket mounting kit is also available separately. i40 Instruments are designed to operate from 12V DC power, and are ultra-efficient drawing less than 0.4 watts for superior run-time and excellent green credentials. The i40 instruments are all covered by Raymarine's industry leading 2-year warranty, upgradeable to 3-years at no charge by registering online with 90 days of purchase. i40 Bidata Instrument The Raymarine i40 Bidata offers all of the functionality of the Depth and Speed instruments combined in a single space-saving display. Like the other i40 Instruments, the Bidata is available as a complete system with depth and speed transducers or as a display-only solution for remote readout of depth and speed at another location. The i40 Bidata's depth capabilities include easy-to-read displays of current speed, maximum speed, average speed, distance log, trip log as well as water temperature. Bidata also offers depth-related alarms and adjustments including shallow depth alarm, deep depth alarm, shallow anchor alarm, and deep anchor alarm, and depth offset controls. Its speed capabilities include displays of current speed, maximum speed, average speed, distance log, trip log as well as water temperature. i40 Key Features Ultra-modern design complements Raymarine's latest a-Series, c-Series and e-Series Multifunction display and instrument systems. High contrast LCD displays with large digits for excellent visibility. Red backlighting for outstanding night-time visibility. Simple SeaTalk networking with other Raymarine instruments, autopilots and MFDs. Built-in transducer connections simplify installation. Small form factor saves space at the helm without sacrificing features. Supplied with: i40 Bidata display E26009 Low profile thru-hull depth transducer E26008 Low profile thru-hull speed and temp transducer i40 Suncover

i50 SeaTalkng Instruments - Depth w/Nylon Thru-Hull Transducer The all-new i50 Instruments from Raymarine offer boaters an excellent combination of great looks, high performance and extreme value. Designed to accommodate either stand-alone or fully integrated installations, the i50 instruments feature Raymarine's exclusive SeaTalkng networking for simple installation and bullet-proof reliability. Each instrument offers extra-large digits, razor-sharp LCD displays and red backlighting for outstanding visibility in all lighting conditions. i50 Digital Instrument displays are fully compatible with our i70 Color Multifunction Instrument too. Boaters can now customize their systems with any combination of monochrome LCD, color LCD and analog instruments as needed. Raymarine also offers the p70 and p70R Color Autopilot controllers which also match with our instruments and multifunction displays. For the ultimate in flexibility the i50 Instruments support SeaTalkng 0 CANBUS networking, as well as our original SeaTalk 1 networking. This makes upgrading older instruments a breeze. Connect your analog depth, speed and wind transducers directly to respective instrument display, or use the displays as repeaters for SeaTalkng smart transducer data: the choice is yours. The ultra-sleek design of i50 line is designed to complement our full line of a-Series, c-Series and e-Series Multifunction displays, and looks great on the helm of any boat. Each instrument comes with a low-profile surface mounting kit and silicone rubber sun cover. An optional bracket mounting kit is also available separately. i50 Instruments are designed to operate from 12V DC power, and are ultra-efficient drawing less than 1W as repeaters, or 2.4W while hosting a transducer. All of the i50 Instruments are waterproof to IPX6 standards. The i50 instruments are all covered by Raymarine's industry leading 2-year warranty, upgradeable to 3-years at no charge by registering online with 90 days of purchase. i50 Depth Instrument The i50 Depth Instrument offers accurate and reliable displays of depth, max depth and minimum depth. Shallow and deep depth alarms will keep you alert, along with a shallow and deep anchor alarms. Red backlighting for outstanding night-time visibility. SeaTalkng and SeaTalk-1 connectivity for maximum flexibility Connect additional i50 depth displays Built-in depth transducer connection i50 Key Features Ultra-modern design complements Raymarine's latest a-Series, c-Series and e-Series Multifunction display and instrument systems. Large, crisp LCD displays with high contrast for excellent visibility. Red backlighting for outstanding night-time visibility. SeaTalkng and SeaTalk-1 Networking for maximum flexibility. Fully compatible with i70, p70 and p70R Color Instruments and Autopilots. 110mm x 115mm footprint is identical to older Raymarine ST60+ instrumentation making upgrading easy

i40 Depth w/Thru-Hull Transducer Compact and feature-packed instruments, the i40 series instruments are smart choice for boaters looking high performance and great value. The i40 series is simple to operate thanks to the use of just three control buttons, i40 has extra-large digits and razor-sharp LCD displays and red backlighting for outstanding visibility in all lighting conditions. These SeaTalk® compatible instruments offer full integration with Raymarine autopilots and navigation equipment. The ultra-sleek design of i40 line is designed to complement our full line of a-Series, c-Series and e-Series Multifunction displays, and looks great on the helm of any boat. All i40 Instruments come with a low-profile surface mounting kit and silicone rubber sun cover. An optional bracket mounting kit is also available separately. i40 Instruments are designed to operate from 12V DC power, and are ultra-efficient drawing less than 0.4 watts for superior run-time and excellent green credentials. The i40 instruments are all covered by Raymarine's industry leading 2-year warranty, upgradeable to 3-years at no charge by registering online with 90 days of purchase. i40 Depth Instrument Raymarine's i40 Depth Instrument is available as a complete system with a thru-hull transducer, transom mount or as a display-only kit enabling you to monitor your boat's depth at a remote location. The i40 Depth Instrument offers easy-to-read displays of current depth, and minimum depth recorded. The unit also offers a convenient shallow depth alarm, deep depth alarm, shallow anchor alarm, and deep anchor alarm. The i40 Depth Instrument offers convenient depth offset controls allowing you to calibrate the readout to compensate for projections (rudders, props, skegs etc.) or to display the depth from the waterline of the vessel. i40 Key Features Ultra-modern design complements Raymarine's latest a-Series, c-Series and e-Series Multifunction display and instrument systems. High contrast LCD displays with large digits for excellent visibility. Red backlighting for outstanding night-time visibility. Simple SeaTalk networking with other Raymarine instruments, autopilots and MFDs. Built-in transducer connections simplify installation. Small form factor saves space at the helm without sacrificing features.