|
Polished Stainless Steel Table Pedestal 3" OD x 25-1/2" L
All of TACO's Z76-Series table pedestal columns are tapered on the bottom for a secure fit into the base while also allowing for easy removal and storage.
Features:
Available in satin anodized aluminum rib design or polished stainless steel
Available in three different lengths
Custom heights available based upon minimum order quantities
5-year limited warranty
Specifications:
Finish: Polished
Taper: Single
Material: Stainless Steel
Length: 25-1/2"
|
93.25 |
|
|
Stainless Steel Bow Eye - 3/8" x 4-1/4"
These Bow Eyes are for use as a tie-down point on your boat’s bow. The 3/8" shafts have rolled threads. Constructed of corrosion resistant machined 304 stainless steel. Includes adjustable finish nuts, which provide superior performance over crimp ring style stern eyes. Can be used in conjunction with Lift Eyes (048330 or 048350) for a more robust lifting assembly.
|
15.60 |
|
|
Compression Handle Stainless Steel Non-Locking 3" OD - 1/4 Turn
Features:
Stainless Steel
Non-Locking
3" OD
Compression Handle
1/4 Turn
|
59.99 |
|
|
Compression Handle - 316 Stainless Steel - Non-Locking - 3" OD
Compression handles reduce and eliminate noise and rattle from hatches when the boat is underway. The handle uses acompressed gasket to create a water-tight seal for compartments or hatches.
Outer Diameter: 3"
Cut-Out:2-1/2"
Surface Depth: 1/8" - 5/8"
Fastener: Included
|
83.77 |
|
|
304 Stainless Steel Basket Strainer Only Size 4 for 1/2" Strainer
Features:
Perko 049300499D 304 stainless steel strainer basket for #4 (1/2"-NPT)
Basket Measures 1-13/16"- DIA. X 4-1/16"-High
Overall height with a hoop on top is 5-5/8"
|
57.78 |
|
|
Polished Stainless Steel 2-19/64’’ Rub Rail End Cap
Caps rub rail to finish end of rail and ensure that inserts stay intact.
Features:
Caps rub rail to finish end of rail
Ensures inserts stay intact
Offers a finished look
Stainless Steel Marine Grade 316
Polished
5-Year limited warranty
|
68.28 |
|
|
RH5165
Standard Angle 30° Short Tube
Medium size Short Swivel Base for Stand-Up Rods with Curved Butts. Has 2" OD x 6-1/2" long tube.
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
128.84 |
|
|
RH5167V
Vertical 0° Short Tube
Medium size Short Swivel Base for Stand-Up Rods with Curved Butts. Has 2" OD x 6-1/2" long tube.
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
128.84 |
|
|
Swivel Base Rod Holders
RH5169
Half Angle 15° Short Tube
Medium size Short Swivel Base for Stand-Up Rods with Curved Butts. Has 2" OD x 6-1/2" long tube.
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
128.46 |
|
|
12x12 Polished Stainless Steel Trim Tab Kit
Improve fuel economy and passenger comfort with Uflex electromechanical trim tabs. Featuring electropolished stainless steel planes and low consumption, high speed, composite actuators, these tabs are built to last in the most demanding sea conditions.
Uflex trim tabs have been specifically designed for easy installation using a quick connect bracket actuator, requiring only one small hole per tab through the transom. The patented transom mounting bracket encapsulates the wiring to ensure protection against any wiring damage.
|
1136.96 |
|
|
Polished Stainless Steel Vault Pro - Center Drain Plug & Garboard Assembly
The revolutionary stainless steel Vault center drain plug with a gasket and stainless steel garboard. Specifically designed to replace the shorter and far more expensive T-handle center drain plug.
Features:
Triangular ergonomic cap - no tools required
8” total length for better reach
NPT thread and a backup O-ring for a water-tight fit
The matching garboard utilizes a gasket in place of messy silicone sealants
*Sold as an Individual
|
78.72 |
|
|
Stainless Steel Retractable Transom Tie-Down - 40" - Pair
This stainless steel retractable transom tie-down is one of the best ways to secure your boat to the trailer. The RT40 swivels to ensure that webbing is pulled in a straight line to the boat transom eye. It also features an easy squeeze release mechanism which enables you to quickly and conveniently secure the boat. The optional mounting bracket may be required depending on your trailer. Adjustable up to 48". Sold in pairs.
|
124.43 |
|
|
"ZERO EMI” Recessed 3.5” LED Light - Polished Stainless Steel Bezel - 12VDC
“ZERO EMI” Indoor / Outdoor Recessed 3.5” LED Light 2700K 85 CRI Dimmable LED Replaces 50W Halogen
NO EMMISSIONS
All light, no EMI! With Zero radio emissions these lights can’t interfere with your communication and navigation equipment. Powerful without the hot spots. The 0A series produces a soft, high color rendering light that fills the area. Comes in Polished, Brushed and White finish with frosted lens. Digitally dimmable designed into the electronics means you will not need special circuitry. Three screw mounting compatible with the most popular models. Warm White or Warm White/Red available. Two or Three wire configurations. Simply reverse polarity to switch between colors or wire both white and red directly.
Features:
Zero AIS & VHF Interference
Lower profile design then other halogen and LED offerings.
600 Lumen, 2700K Warm White, >85CRI
IP65 Indoor/Outdoor
|
67.18 |
|
|
“ZERO EMI” Recessed 3.5” LED Light - Polished Stainless Steel Bezel - 12VDC
“ZERO EMI” Indoor / Outdoor Recessed 3.5” LED Light 2700K 85 CRI Dimmable LED Replaces 50W Halogen
NO EMMISSIONS
All light, no EMI! With Zero radio emissions these lights can’t interfere with your communication and navigation equipment. Powerful without the hot spots. The 0A series produces a soft, high color rendering light that fills the area. Comes in Polished, Brushed and White finish with frosted lens. Digitally dimmable designed into the electronics means you will not need special circuitry. Three screw mounting compatible with the most popular models. Warm White or Warm White/Red available. Two or Three wire configurations. Simply reverse polarity to switch between colors or wire both white and red directly.
Features:
Zero AIS & VHF Interference
Lower profile design then other halogen and LED offerings.
600 Lumen, 2700K Warm White, >85CRI
IP65 Indoor/Outdoor
|
74.41 |
|
|
“ZERO EMI” Recessed 3.5” LED Light - Warm White, Blue with Polished Stainless Steel Bezel - 12VDC
“ZERO EMI” Indoor / Outdoor Recessed 3.5” LED Light 2700K 85 CRI Dimmable LED Replaces 50W Halogen
NO EMMISSIONS
All light, no EMI! With Zero radio emissions these lights can’t interfere with your communication and navigation equipment. Powerful without the hot spots. The 0A series produces a soft, high color rendering light that fills the area. Comes in Polished, Brushed and White finish with frosted lens. Digitally dimmable designed into the electronics means you will not need special circuitry. Three screw mounting compatible with the most popular models. Warm White or Warm White/Red available. Two or Three wire configurations. Simply reverse polarity to switch between colors or wire both white and red directly.
Features:
Zero AIS & VHF Interference
Lower profile design then other halogen and LED offerings.
600 Lumen, 2700K Warm White, >85CRI
IP65 Indoor/Outdoor
|
74.41 |
|