Stop Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

Stop Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

Cap Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

"L" Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

Teak Edge Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

"L" Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

3/4" Teak Bulkhead Molding 3/4" Track Corner Cap/Hand Hold Bulkhead Molding 3/4" inside track Use with 60825

Quarter Round Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

Edge Molding Outside Corner Edge Molding Inside radius: 2" Outside radius: 2-1/2"

Edge Molding Inside Corner Edge Molding Inside radius: 1-3/4" Outside radius: 2-1/4"

Teak Deck Steps 8-3/4"L x 3-1/2"W x 1/2"H

Teak LED Dome Light - 5" Lens  These LED Dome Lights feature a solid teak base with a lacquer coated brass trim ring. Prewired with integral on/off toggle switch. Low current consumption of 0.068 amps @ 12 volts, they give off very little heat and have extremely long service life. These vibration resistant LED Dome Lights feature 18 white LEDs per light. Surface mounts with #8 FH fasteners (not included). WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Standard Pin Rail 3-9/16"H x 7/8"D x 5'L 5' length

GP1040-15 SystemPod Pre-Cut for Raymarine c95/c97/e95/e97 & 1 Instrument for 9.5" Wide Guard NavPod GP1040 Series for 9.5" Guard SystemPods for Sail are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic. A SystemPod is best mounted on a Single Bend AngleGuards. SystemPods for Power are for mounting on a SK135 Stachion Kit can be used to mount a SystemPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SystemPod for overhead mounting applications. Sizing: Overall Size: 9.5"H x 20.75"W x 6"D Usable Face: 7.375"H x 17.5"W x 5"D Max Cutout: 7"H x 17"W Instrument Cutout: 3.6" All SystemPods include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets *See Literature tab for an image with dimensions

GP1523 SystemPod Pre-Cut for Raymarine a75/a77/a78 Mounted In Center for 9.5" Wide Guard GP1500 Series for 9.5" Guard, SystemPods for Sail are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic. A SystemPod is best mounted on a Single Bend AngleGuards. SystemPods for Power are for mounting on a SK135 Stachion Kit can be used to mount a SystemPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SystemPod for overhead mounting applications. All SystemPods include Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Stainless steel mounting hardware and mounting gaskets *See Literature tab for an image with dimensions