Footman's Strap Mount The Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie downs and mounting heavy hoses and cables or deck mounted for life raft tie downs.

Footman's Strap Mount The Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie downs and mounting heavy hoses and cables or deck mounted for life raft tie downs.

{Standard Start-Up Kit - No Adhesive The 65109 Start Up Kit has a wide variety of Weld Mount parts designed to give the user the chance to try numerous applications at a low cost. Kit Contains: 1 pc AT-300 Adhesive Dispensing Gun 5 pc. AT-850 Adhesive Mixing Tips 50 pc. AT-5 White Tie Mount 2 pc. AT-113 Blarge Black Footman's Strap 4 pc. ST125-1420-12SS 1.00" Stainless Stud 1 Plano Storage Box 11" x 7.25" x 2.75"

AT-5 Large White Nylon Tie Mount - Qty. 500 The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Industrial Kit with AT-8040 Adhesive This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For Industrial Maintenance Shops. A Wide Selection Of Weld Mount Parts Are Supplied In A Heavy "Durham" Metal Box Which Is A Standard Rack Mounted System. The Kit Contains 1 Tubes Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastics And Rubber. AT-8040 Will Hold Even Our Heaviest Parts On An Overhead Or Vertical Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225 Degrees. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 1 year. The Weld Mount System Eliminates The Need To Drill And Tap, or Weld When Used On Metal Surfaces. Great for Mounting Wire and Conduit Runs, Electrical Boxes And Other Structural Applications. The AT-7001 Kit Contains: (1) AT-8040 - No Slide Multi Bonder Adhesive With 12 Minute Kick (10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive (1) AT-300 - Adhesive Dispensing Gun (30) AT-3B - Small Black Cable Tie Mount (100) AT-5B - Large Black Cable Tie Mount <(25) AT-5 - Large White Cable Tie Mount (25) AT-7 - Aluminum Base Swivel Wire Tie Mount (25) AT-9 - Aluminum Wire Tie Mount (2) AT-113 - Large Footman's Strap White (2) AT-113B - Large Footman's Strap Black (6) ST125-1420-12SS - 0.75" Long Stud With 1/4 x 20 Threads 1.25" Base (6) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base (6) ST125-1024-12SS - 0.75" Long Stud With #10 x 24 Threads 1.25" Base (6) ST125-1024-20SS - 1.25" Long Stud With #10 x 24 Threads 1.25" Base (2) SHC-1000 - Single Hose Clamp 1.00" (2) DHC-1000 - Double Hose Clamp 1.00" (1) Storage Box - Durham Manufacturing 18.5' x 12.5" x 3.25" Step By Step Instructions

Industrial Kit - No Adhesive This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For Industrial Maintenance Shops. A Wide Selection Of Weld Mount Parts Are Supplied In A Heavy "Durham" Metal Box Which Is A Standard Rack Mounted System. The Weld Mount System Eliminates The Need To Drill And Tap, or Weld When Used On Metal Surfaces. Great for Mounting Wire and Conduit Runs, Electrical Boxes And Other Structural Applications. The AT-7008 Kit Contains: (10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive (1) AT-300 - Adhesive Dispensing Gun (30) AT-3B - Small Black Cable Tie Mount (100) AT-5B - Large Black Cable Tie Mount (25) AT-5 - Large White Cable Tie Mount (25) AT-7 - Aluminum Base Swivel Wire Tie Mount (25) AT-9 - Aluminum Wire Tie Mount (2) AT-113 - Large Footman's Strap White (2) AT-113B - Large Footman's Strap Black (6) ST125-1420-12SS - 0.75" Long Stud With 1/4 x 20 Threads 1.25" Base (6) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base (6) ST125-1024-12SS - 0.75" Long Stud With #10 x 24 Threads 1.25" Base (6) ST125-1024-20SS - 1.25" Long Stud With #10 x 24 Threads 1.25" Base (2) SHC-1000 - Single Hose Clamp 1.00" (2) DHC-1000 - Double Hose Clamp 1.00" (1) Storage Box - Durham Manufacturing 18.5' x 12.5" x 3.25" Step By Step Instructions

AT-3 Small White Nylon Tie Mount - Qty. 500 The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

AT-5B Large Black Nylon Wire Tie Mount - Qty. 500 The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

AT-14 1 to 1 Adhesive Gun Plunger f/AT-2010, AT-4020 & AT-6030 Adhesives AT-14 is specifically for Weld Mount AT-2010, AT-4020 and AT-6030 adhesives.

Executive Adhesive & Fastener Kit w/AT-8040 Adhesive This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Contains 1 Tube Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastic Or Rubber. AT-8040 Will Hold Even Our Heaviest Parts on a Vertical or Overhead Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225°. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 1 year. The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc. The AT-1001003 Kit Contains: (1) AT-8040 - No Slide Multi Bonder Acrylic Adhesive <(1) AT-300 - Dispensing Gun (10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive (100) AT-5 - Large White Cable Tie Mount (50) AT-3 - Small White Cable Tie Mount (4) AT-113 - Large Footman's Strap (10) PS62-832-16SS - 1.00" Long Panel Stud (4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base (4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base (4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base (4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base (1) Plano Storage Box 14" x 9" x 2.75" Step By Step Instructions

Executive Fastener Kit - No Adhesive This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Does NOT Contain Acrylic Adhesive The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc. The AT-1001008 Kit Contains: (1) AT-300 - Dispensing Gun (10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive (100) AT-5 - Large White Cable Tie Mount (50) AT-3 - Small White Cable Tie Mount (4) AT-113 - Large Footman's Strap (10) PS62-832-16SS - 1.00" Long Panel Stud (4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base (4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base (4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base (4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base (1) Plano Storage Box 14" x 9" x 2.75" Step By Step Instructions

White Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.