External smartAIS Alarm & Mute Switch Kit for WatchMate XB-8000 The WatchMate XB-8000 smartAIS has the ability to trigger an external alarm that can be mounted anywhere onboard. If the XB-8000 detects a risk situation due to a potential collision, anchor drag, or a MOB activation, it alerts you with an alarm on your mobile device. It simultaneously sounds the external alarm which operates even if your mobile device is turned off. The alarm is designed to be easily mounted and can be connected directly to the XB-8000 without the need for external relays or other components. By simply rotating the sound output vane you can control the volume level. It is easily configured to make a steady continuous or pulsing tone like a truck backup alarm. It is heavy-duty and very robust. Its terminals are via screw down or you can use 6.35mm (1/4") quick disconnects. This alarm can be used with both 12 and 24 VDC systems. It also has reverse polarity protection to prevent damage due to incorrect wiring. Mute Switch for XB-8000 The Switch is used to mute the Alarm. Its 304 stainless steel body is durable and waterproof making it ideal for mounting both internally or externally. It is designed to be used with 12 and 24 VDC systems. Alarm Specifications: Rated voltage: 12-32 VDC (reverse polarity protected) Maximum voltage: 32 VDC Maximum current: 35 mA Frequency: 2.9 kHz (+/- 0.5) Configuration: Makes either a steady or pulsed sound (choose S or P terminal) Sound pressure: 85 steady, 80 pulsed dBA/30cm Volume adjustment: Twist front vane holes to closed to reduce volume Pulse rate: 0.8 - 1.2 pulse/sec Size: Diameter: 43.5mm (1 3/4"), Height: 34.5mm (1 3/8") Mounting hole: 29mm (1 3/16") Switch Specifications: Voltage Range:10-32 VDC LED Color: Blue Button & Body: 304 Stainless Steel Contact Materia: lSilver Alloy Cable:150mm (6”) Tinned Panel Thickness: 1 10mm Operating Temp: -20C +55C Insulation Resistance: ≥ 1000MΩ Contact Resistance: ≤ 50mΩ Degree of Protection: IP65

Helm Switch Kit R001441 includes - rocker switch face plate and four screws (Replacement for P7817800AJ)

External GPS Antenna with 8" Cable for Cortex M1 & 10M Coax Cable External GPS Antenna for Cortex M1 with 8" (200mm) cable. This multi-constellation GNSS Antenna is designed as an external antenna for the Cortex Hub, WatchMate Vision, or XB series of AIS transponders . It is IP67 and UV stable for use in a harsh marine environment. GNSS (Global Navigation Satellite System) includes GPS, GLONASS, Bei Dou and Gallileo positioning networks. Features: Small SMA connector for easy installation Pre-wired 200mm (8”) RF cable for easy servicing Two mounting configurations (deck or under deck) UV stable housing provides good color stability Specifications: UV stable plastic with a zinc-plated alloy base Dimensions: 60mm x 19mm Loom: 200mm Color: White Mounting: Bulkhead, pole, deck, and underdeck mounting

High Water Bilge Alarm with Switch & Gauge - 24V Using a compact float switch and dash mounted alarm, Rule provides boaters with a warning to high bilge water levels. Ideal for larger yachts and commercial vessels larger than 26' with unmanned compartments that have to comply with CFR 182.530. A bright LED indicator light provides a visual alarm when ambient noise levels exceed alarm volume. Constantly monitor your bilge for water and stay compliant to Coast Guard regulations with a Hi-Water Bilge Alarm from Rule. Features: Visible and audible alarm to monitor bilge water levels Includes mercury-free float switch and dash mounted alarm Complies with CFR 182.530 24V WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

9" x 12" Standard Trim Tab Kit w/Standard Integrated Switch Kit- 12V  Lenco Electric Complete Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Standard Trim Tab blades are 12 Gauge - 304 SS with a 5/8" flared trailing edge and 1/8" diameter hinge pin. Kits include standard actuators with 5/16" SS bolts. Lenco Trim Tab Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. Kit includes:  Self-contained sealed keypad Control box 36" Pigtail Specifications: Suggested Boat Length: 16' to 25' Length of Tab: 9" Width of Tab: 12" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: Standard Tactile Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

9" x 12" Standard Trim Tab Kit w/LED Integrated Switch Kit- 12V  Lenco Electric Complete Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Standard Trim Tab blades are 12 Gauge - 304 SS with a 5/8" flared trailing edge and 1/8" diameter hinge pin. Kits include standard actuators with 5/16" SS bolts. Lenco Trim Tab Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. Kit includes:  Self-contained sealed keypad Control box 36" Pigtail Specifications: Suggested Boat Length: 16' to 25' Length of Tab: 9" Width of Tab: 12" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: LED Indicator Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 12" Edge Mount Trim Tab Kit w/Standard Tactile Switch Kit  - 12V  Lenco Electric Complete Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs. Lenco Trim Tab Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. Kit includes:  Self-contained sealed keypad Control box 36" Pigtail Specifications: Suggested Boat Length: 17' to 30' Length of Tab: 12" Width of Tab: 12" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: Standard Tactile Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 12" Edge Mount Trim Tab Kit w/LED Indicator Switch Kit  - 12V  Lenco Electric Complete Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs. Lenco Trim Tab Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. Kit includes:  Self-contained sealed keypad Control box 36" Pigtail Specifications: Suggested Boat Length: 17' to 30' Length of Tab: 12" Width of Tab: 12" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: LED Indicator Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 12" Standard Trim Tab Kit w/LED Integrated Switch Kit - 12V  Lenco Electric Complete Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Standard Trim Tab blades are 12 Gauge - 304 SS with a 5/8" flared trailing edge and 1/8" diameter hinge pin. Kits include standard actuators with 5/16" SS bolts. Lenco Trim Tab Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. Kit includes:  Self-contained sealed keypad Control box 36" Pigtail Specifications: Suggested Boat Length: 17' to 30' Length of Tab: 12" Width of Tab: 12" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: LED Indicator Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Edge Mount Trim Tab Kit w/Standard Tactile Switch Kit Lenco Electric Edge Mount Trim Tab Kits make your boat ride smoother, dryer, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ball screw design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs. Suggested Boat Length:16'-25' L" x W": 9" x 12" Hinge Height: 2" Minimum Transom Height: 13.5" Kit Contents 2 each of 12-gauge stainless steel trim tab blades 2 each of #15054-001 actuator with 6' leads & Deutsch plugs 2 each of #30133-103 20' actuator extension wiring harnesses 2 each of #15085-001 (116) upper mounting brackets with gland seal 2 each of #50014-001 (119) lower mounting brackets 1 each of the Lenco owner's / installation manual All necessary stainless steel mounting hardware Specifications: Blades: 12 Gauge Stainless Steel Finish:Smooth Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Standard Tactile Switch Kit With Built-In Retractor For Single Actuator Systems / 12-Volt Lenco Trim Tab Standard Tactile Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. The switch itself is completely waterproof, and has an over-molded connector to eliminate water intrusion. The standard tactile switch is built to all the same exacting standards as the indicator switches. Kit Contents Key Pad Control Box 36" Power Pigtail WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Edge Mount Trim Tab Kit w/LED Indicator Switch Kit Lenco Electric Edge Mount Trim Tab Kits make your boat ride smoother, dryer, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ball screw design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs. Suggested Boat Length:16'-25' L" x W": 9" x 12" Hinge Height: 2" Minimum Transom Height: 13.5" Kit Contents 2 each of 12-gauge stainless steel trim tab blades 2 each of #15054-001 actuator with 6' leads & Deutsch plugs 2 each of #30133-103 20' actuator extension wiring harnesses 2 each of #15085-001 (116) upper mounting brackets with gland seal 2 each of #50014-001 (119) lower mounting brackets 1 each of the Lenco owner's / installation manual All necessary stainless steel mounting hardware Specifications: Blades: 12 Gauge Stainless Steel Finish:Smooth Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat LED Indicator Switch Kit With Built-In Retractor & Self-Check Features For Single Actuator Systems / 12 & 24-Volt Lenco Waterproof Trim Tab Tactile Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. The Lenco indicator switch is the most advanced trim tab switch available. The switch itself is completely waterproof, and has an over-molded connector to eliminate water intrusion. L.E.D. indicator lights let you know exactly where your trim tabs are at all times. A backlit keypad automatically illuminates graphics for night viewing. A photo eye reads ambient light and adjusts the indicator intensity for optimum viewing in all lighting conditions. The standard tactile switch is built to all the same exacting standards as the indicator switches. Kit Contents Self-contained sealed Key Pad Control box 36" Power Pigtail. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 12" Standard Trim Tab Kit w/Double Rocker Switch Kit - 12V  Lenco Electric Complete Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Standard Trim Tab blades are 12 Gauge - 304 SS with a 5/8" flared trailing edge and 1/8" diameter hinge pin. Kits include standard actuators with 5/16" SS bolts. Lenco Trim Tab Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. Kit includes:  (1) Switch Kit (2) 12-Gauge Stainless Steel Standard Finish Blades (2) 15054-001 Actuators with 6 foot Leads and Deutsch Connectors (2) 30133-103 Actuator Extension Wiring Harnesses- 20 foot length (2) 15085-001 Upper Mounting Brackets with Gland Seal (2) 50014-001 Lower Mounting Brackets Lenco Owner's/ Installation Manual Stainless Steel Mounting Hardware Specifications: Suggested Boat Length: 17' to 30' Length of Tab: 12" Width of Tab: 12" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: Double Rocker Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

LED Indicator Two-Piece Tactile Switch Kit with Pigtail for Single Actuator Systems This LED tactile switch kit has a shortened bezel for consoles which require less depth to mount. Functionality is built into the externally mounted control box and must be mounted separately. LED indicator lights let you know exactly where your trim tabs are at all times. A backlit keypad automatically illuminates graphics for night viewing. A photo eye reads ambient light and adjusts the indicator intensity for optimum viewing in all lighting conditions. Features Include Simple, quick, Plug & Play installation Instant response Built-in retractor Low profile design Self-contained, sealed key pad & solid state control box with waterproof Plug & Play Deutsch connectors 36" power pigtail for control box 2 1/16" hole cut-out size, overall key pad size of 2.75" x 2.75" 2.33" clearance required from the back of the key pad's mounting location 2 high-intensity LED Indicator displays show the exact position of your trim tabs at all times Photo Eye for optimum viewing in all light conditions Backlit key pad for optimum viewing at night Self-Check feature ATTENTION: REPLACEMENT KEY PADS & CONTROL BOXES FOR 2016 & PRIOR SWITCHES ARE NOT COMPATIBLE WITH THIS SWITCH KIT. Replacement parts are available and are sold separately.  Specifications 3 Year Warranty System Type:Single Actuator Compliance:CE Certified WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

LED Indicator Two-Piece Tactile Switch Kit w/Pigtail f/Dual Actuator Systems This LED tactile switch kit has a shortened bezel for consoles which require less depth to mount. Functionality is built into the externally mounted control box and must be mounted separately. LED indicator lights let you know exactly where your trim tabs are at all times. A backlit keypad automatically illuminates graphics for night viewing. A photo eye reads ambient light and adjusts the indicator intensity for optimum viewing in all lighting conditions. Features Include Simple, quick, Plug & Play installation Built-in retractor Low profile design Self-contained, sealed key pad & solid state control box with waterproof Plug & Play Deutsch connectors 72" power pigtail for control box 2 1/16" hole cut-out size, overall key pad size of 2.75" x 2.75" 2.33" clearance required from the back of the key pad's mounting location 2 high-intensity LED Indicator displays show the exact position of your trim tabs at all times Photo Eye for optimum viewing in all light conditions Backlit key pad for optimum viewing at night ATTENTION: REPLACEMENT KEY PADS & CONTROL BOXES FOR 2016 & PRIOR SWITCHES ARE NOT COMPATIBLE WITH THIS SWITCH KIT. Replacement parts are available and are sold separately.  Specifications 3 Year Warranty System Type: Dual Actuator Compliance: CE Certified WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 12" Edge Mount Trim Tab Kit w/Double Rocker Switch Kit  - 12V  Lenco Electric Complete Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs. Lenco Trim Tab Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. Kit includes:  Self-contained sealed keypad Control box 36" Pigtail Specifications: Suggested Boat Length: 17' to 30' Length of Tab: 12" Width of Tab: 12" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: Double Rocker Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.